the stops, as shown in the figure below. With an outside atmospheric pressur should the water pressure (in kPa) be to lift the piston? Po 0.0 g

Q: The diesel engines operates with low pressure than petrol engine a. FALSE b. TRUE

A:

Q: Compression takes place on both sides of the piston in two cylinders is known as a. single stage…

A: Here, whenever a single cylinder is used and compression takes place on both sides of cylinder. Then…

Q: At critical pressure, value of Hg-Hf is *

A: At critical pressure, value of Hg-Hf is Answer: 0 (zero)

Q: Give a concise introduction on Self pressurizing reservoirs

A: Self pressurizing reservoirs :-

Q: The rotary compressor gets its name from the fact that it has an off-center piston of rotor which…

A: This question is based on the concept of conpressors.

Q: In a double acting reciprocating pump, the piston carries suction and expulsion at the not same…

A: Yes, it is true.

Q: Write the classification of air compressor based on the principle of operation.

A: The four most common sorts of air compressors are: Rotational Screw Compressor. Reciprocating Air…

Q: Give a concise introduction on Douglass pressurized reservoirs.

A: DOUGLASS PRESSURIZED RESERVOIR :- Douglass pressurized reservoir is a tank which has immense…

Q: iscuss what is the effect of efficiency on compressor temperature and duty.

A: A compressor is a device that reduces the volume of a material (typically a gas) to raise its…

Q: What is the angle between the cylinders of this compressor?

A: The above given figure is that of a V shaped compressor.The angle between the cylinders of the…

Q: Explain about ball valve and also write the working pressure and temperature limit of ball valve.

A: A ball valve is the quarter turn valve which uses a hollow, perforated and pivoting ball to control…

Q: n of refrigeration me

A: given: one ton of refrigeration means?

Q: 1. (- If you shoot, using a 0.45 caliber pistol, a SolaneTM LPG tank, will it explode Moreover, why…

A: 1. Shooting a fuel tank with a 0.45 calibre handgun will not cause it to explode. If it is a…

Q: For the container shown in the previous problem, how do the pressures at points A, C, D compare…

A: At the free surface f the liquid in a container there is atmospheric pressure.But for the other…

Q: Which of the following statements are true? Select all that apply. O a. Pressure increases in a…

A: Find the effect of pump and turbine on pressure and velocity.

Q: A pipe has a Re of 1000, what is the friction factor?

A:

Q: Which type of compressor uses V-belt to create compression in the compresso

A: V-belt: These types of belt are most widely used in factories and workshops where a great amount of…

Q: What is fan static pressure?

A: Fan static pressure:-static pressure is the most important parameter which defines the performance…

Q: An Hcylinder has the following markings on it DOT 3AA 5000 menyfactare 10% more when Infull service…

A: Given : 25 LPM To find: How long it will last

Q: 5. Why does pressure increase when the piston rod is fully extended or retracted? *****

A: Piston rod-In large two-stroke engines, piston rods are frequently utilised. The cross head and the…

Q: Which one of the following is true to reduce the work input to a compressor O increase the pressure…

A:

Q: To determine: The type of change in suction pressure when evaporator experiences a heat-load…

A: Given data : Suction pressure  Heat load increase

Q: Question 3 A four-cylinder of 1.6 liters S.I engine (S4PH with BSFC = 0.5 lb/HP- hour) has the…

A: Given dataN=4BSFC=0.5Injector size =240 cc/minQ'=240 cc/minP'=43.5 psiP=50 psi ***As per company…

Q: Determine the type of steam, given: Temperature: 52°C Enthalpy: 2590 k/kg O wet Vapor Superheated…

A: Given that, From the steam table, write the properties of steam.

Q: Give all the parts of a simple vertical fire tube boiler

A:

Q: Give an example of Reducing the Air Pressure Setting.

A: The setting of reducing air pressure is concerned with the setting of the air compressor. Air…

Q: On the low-pressure side of a double diaphragm seal system, the transmitter measures a pressure of…

A: Given: There are double diaphragm seal system. On the side of low pressure there are a pressure of…

Q: id you get the specific heat of water?

A: Specific heat of water

Q: What are the results and discussions in discussing the function of each component of the valve…

A: A valve is a mechanism or natural item that opens, closes, or partially obstructs numerous passages…

Q: In a pressure regulator, the ________ is attached to one end of the poppet to provide a surface for…

A: Pressure Regulator, A pressure regulator is a device which controls the pressure of liquids or gases…

Q: Which one of the following is true to reduce the work input to a compressor O increase the pressure…

A: The expression for the Work absorbed by the compressor is given below as- W=2nRT1n-1pxp1n-1n-1…

Q: what is Cp of the air Properties and Compressor

A:

Q: The compressor which is is used in our experiment is a. Two Stage reciprocating compressor in which…

A: Basic knowledge of 2 - stage reciprocating air compressor.

Q: 3- List two reason, to keep low pressure drop across the production system. 5- W... a

A: Pressure drop is the most common and significant problem observed in production system. It basically…

Q: QUESTION 15 Determine the type of steam. given: Temperature: 95°C Pressure: 100 kPa O superheated…

A: The pressure is equal to the 1 bar pressure and the temperature of the water is 95oC. As we know the…

Q: How many piston does a two stroke engine have

A: A two stroke engine with single cylinder will have one piston and it takes two strokes of the single…

Q: The minimum pressure at which the valve starts opening is called O a. breaking pressure O b.…

A:

Q: When performing a coolant pressure test, Technician A says to pressurize the system to the pressure…

A:

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.