The steel tube below has an inside diameter of 2.75”, and an outside diameter of 3”. If the tube is fixed at C, and subjected to the 20 lb horizontal force acting on the wrench as shown, determine the principal stresses in the point A, which is located on the surface of the tube

Q: The block is subjected to axial loa normal tension developed at poir the distribution of the normal…

A:

Q: Determine the stress components acting on the inclined plane AB. Solve the problem using the method…

A:

Q: Air pressure in the cylinder is increased by exerting forces P = 2 kN on the two pistons, each…

A: Given Data: The outer radius of the cylinder is: rO=47 mm The force exerted on the walls is: P=2…

Q: The state of stress at the point can also be represented in termsof the maximum in-plane shear…

A: False, The state of stress at the point cannot be represented in terms of the maximum in-plane shear…

Q: If the force P equals 2500 lbs. Determine the maximum tensile stress in the section of the hook…

A:

Q: a) the principal stress and planes and (b) the maximum in-plane shear stress, average stress and its…

A:

Q: Determine the normal and shear stresses at point B. 5-10 min 180 mm 180 mm 60 mm - 30 KN

A: Given data dimension of cross section = 180mm× 60 mm find the normal and shear stress at point B.

Q: Q1/ The copper pipe has an outer diameter of 3.0 in. and an inner diameter of 2.8 in. If it is…

A:

Q: Steel wire AB and aluminum wire CA support the 400 kg mass as shown. Determine the required diameter…

A:

Q: Q2: If the block is subjected to the centrally applied force of 600 kN, determine the average normal…

A: Given: the block is subjected to applied force =600 kN we have to find the average normal stress in…

Q: For the given state of stress, determine the normal and shearing stresses exerted on the oblique…

A:

Q: N THE SYSTEM SHOWN AS BELOW, A FORCE OF 200 N AFFECTS ON THE PIPE SWITCH. CONSISTING AT POINTS A AND…

A:

Q: 1. The steel water pipe has an inner diameter of 12 in. and wall thickness 0.25 in. If the valve A…

A: To find: The longitudinal and hoop stress developed in the wall of the pipe, also draw the stress on…

Q: d2 mm 60 mm FAN dlmm 10 mm 40 mm The shaft shown is subjected to the axial force(F) of 30 kN. If the…

A:

Q: Determine the stress components acting on the plane AB. Solve the problem using the method of…

A:

Q: 3-Determine the maximum vertical force P that can be applied to the bell crank so that the average…

A:

Q: Rods AB and BC have diameters of 4 mm and 6 mm, respectively. If the 3 kNforce is applied to the…

A:

Q: 1. The cylindrical pressure vessel has an inner radius of 1.25 m and a wall thickness of 15 mm. It…

A: Given data :- The inner radius = 1.25 m                         The thickness of wall = 15 mm…

Q: a force q of magnitude 3kips is applied to machine element ab. the uniform thickness of the element…

A: Given data Force (Q) = 3 Kips Thickness (t) = 0.8 in

Q: 9-74 If the box wrench is subjected to the 50 lb force, determine the principal stresses and maximum…

A:

Q: Rods AB and BC have diameters of 4 mm and 6 mm, respectively. If the 3 kN force is applied to the…

A: Given, The diameter of AB(dAB) = 4 mm The diameter of BC(dBC) = 6 mm Load (P) = 3 kN For Member…

Q: The bar has a diameter of 40 mm. Determine the state of stress at point A and show the results on a…

A: Section properties can be determined as

Q: The steel pipe has an inner diameter of 2.75 in. and an outer diameter of 3 in. If it is fixed at C…

A: Write the given data: Understand the effects of the 20 lb force on the member CD as shown in the…

Q: The solid bar has a diameter of 50 mm. The two forces and the x-y-z coordinate system which is…

A:

Q: A basketball has a 300-mm outer diameter and a 3-mm wall thickness. Determine the normal stress in…

A: Outer diameter, D = 300 mm  Wall thickness, t = 3 mm  Inner diameter, d = D - 2t = 300 - (2*3)  d =…

Q: 5. Two forces act on the solid circular rod (r=.005 m) as shown. Using Mohr's circle, determine the…

A: Draw mohr circle and find principal stresses and maximum shear stress.

Q: The clamp presses the smooth surface at E when tightening the screw. If the tension in the bolt is…

A: Given data as per question Tension in the bolt =40 kN   Support reaction are shwn on FBD (a)Internal…

Q: The steel rod has a circular cross section. If it is loaded by a 500 lb vertical force as shown,…

A:

Q: 4-The long bolt passes through the 30-mm-thick plate. If the force in the bolt shank is 8 kN,…

A:

Q: The solid cylinder having a radius r is placed in a sealed container and subjected to a pressure p.…

A: Explanation: ◆ The solid cylinder is subjected to a pressure p inside the sealed cylinder.  ◆ The…

Q: The solid bar has a diameter of 50 mm. The two forces and the torque Tx are acting at the origin of…

A:

Q: The cross-sectional area of the bar ABCD is 600 mm². Determine the maximum normal stress in the bar?

A: Assume that the bar ABCD is The load acting on the bar is P The maximum normal stress then act on…

Q: The thin-walled pipe has an inner diameter of 0.5 in. and a thickness of 0.025 in. If it is…

A: Given: The thickness of the wall is t=0.025 in. The inner diameter of the wall is d=0.5 in. The…

Q: Determine state of stress at the remaining points (P2, P3 and P4). Calculate the maximum principal…

A: Given: Outer Diameter of the Pole do=115 mm=0.115 m inner Diameter of the Pole di=100 mm=0.1 m To…

Q: | Determine the stress components acting on the inclined plane AB. Solve the problem using the…

A: We have to solve the equilibrium methods

Q: The sign is supported by a hollow structural tube of 15 in. outer diameter and 0.5 in. wall…

A:

Q: Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 40 kN if it…

A:

Die Stock

Die stock is expressed as the type of component which is utilized for fitting purposes while creating or shaping uniform threads on tubes, pipes, or screws. The die stock (die handle) has three screws around the adjustable part of a particular machine that helps to locate the die. Also, die stock can endure on a variety of hex and split adjustable dies of several dimensions. One of the primary reasons for using die stock in industries is because die stock can be operated by hands. Commonly, it is made up of high carbon steel.