2 PoinQuestion 7 of 15The steel plate shown below is put in into a rigid chamber, such that spacings of size s = 0.00188 m. To fit the plate, it is heated. It can be assumed that theplate can move frictionless along its edges. If x 4 m and y=2m,E = 200 GPaV = 0.28a = 11.7 x 10 rcFor which temperature increase along the y-axis is the upper spacing just closing in degree celsius?Select the correct response

Answered: Image /qna-images/answer/93d752a8-1a39-47fe-9c13-2efa1b5c39e1.jpg

The steel plate shown below is put in into a rigid chamber, such that spacings of size s 0.00188 m. To fit the plate, it is heated. It can be ass plate can move frictionless along its edges. If x- 4 m and y-2m, E - 200 GPa V - 0.28 a - 11.7 x 10 rC For which temperature increase along the y-axis is the upper spacing just closing in degree celsius?

The steel plate shown below is put in into a rigid chamber, such that spacings of size s 0.00188 m. To fit the plate, it is heated. It can be ass plate can move frictionless along its edges. If x- 4 m and y-2m, E - 200 GPa V - 0.28 a - 11.7 x 10 rC For which temperature increase along the y-axis is the upper spacing just closing in degree celsius?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A HA He 1 m L 1 m
The steel plate shown below is put in into a rigid chamber, such that spacings of size s = 0.003 m. To fit the plate, it is heated. It can be assumed that the plate can move frictionless along its edges. If x = 4 m and y = 2 m, E = 200 GPa !! V = 0.28 = 11.7 x 10 FC Which temperature increase along the x-axis is required to just close the spacing on the right in degree celcius? Select the correct response 85.470 O 64.103 040.171 32.051
Q1. An aluminum rod is rigidly attached between a steel rod bronze rod as shown in figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will n exceed a stress in steel of 90 MPa, in aluminum of 140 MPa bronze of 120 MPa. Aluminum Вronze A= 300 Steel A=100 A=200 ЗР 2P 5P 2.5m 2.0 m 1.5 m
2. A rod is composed of an aluminum section rigidly attached between steel and bronze sections as shown in the figure. Axial loads are applied at the positions indicated. The cross-sectional area of the rod is 300sq.mm. Express your answer in MPa. Determine the stress in the steel. b. a. Determine the stress in the aluminum. Determine the stress in the bronze. C. STEEL ALUMINUM BRONZE 56kN 14kN -0.6m- -0.9m- -0.76m-
DEFORMATION DUE TO AXIAL FORCES PROBLEM 1: CE Brd Exam The rigid block shown weighs 176.4 kN. It is held in position shown with stress in the supporting rods shown initially zero. If the former is to remain horizontal when released, 1a. Find the ratio of forces in bronze and steel a. 0.389 c. 0.397 1b. Find the stress in the bronze rod. b. 0.344 d. 0.416 а. 31.92 MPа с. 28.73 МPа 1c. Find the the elongation of steel rod. b. 53.34 MPa d. 39.67 MPa a. 0.615 mm b. 1.83 mm c. 2.31 mm d. 2.12 mm 0.6 m BRONZE A=900mm STEEL STEEL A=600mm A=600mm 1 m E-200GPA E-83GPA E=200GPA W = 176.4 kN
The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontal before the load P is applied. Determine the maximum value for P If the stress must not exceed: 160 MPa for steel and 80 MPa for Bronze. Then determine the vertical movement of P. BRONZE L-5 m A 500 mm E-80 GPa STEEL L-4 m A-400 mm E-200 GPa 3 m. 5 m. VP
Mechanics of Deformable Bodies Problem: The figure shows the upper half of a built up girder( the cross section is symmetric about the neutral axis). All rivets used in fabrication have a diameter of 22 mm. The moment of inertia of the entire cross sectional area of the girder about the neutral axis is l=4770x10⁶mm⁴. The working stresses are 100 MPa for rivets in shear and 280 MPa for bearing of the web plate. If the maximum shear force carried by the girder is 450 kN, determine the largest allowable spacing of rivets that join the angles to the web plate.
3) An bronze rod is rigidly attached between a aluminum rod and a steel rod as shown. Axial loads are applied at the positions indicated. Find the maximum allowable value of P that will not exceed a stress in steel of 140MPA, in aluminum of 90MPA or in bronze of 100MPа. Aluminum A = 500mm? Bronze A = 200mm? Steel A = 150mm2 2P ЗР L st = 1.2m L br = 2m Lal = 3.5m
Problem 1 A bar obtained by bonding together pieces of aluminum (E, = 70 GPa) and brass (E, = 105 GPa) has the cross section shown below. Considering that the allowable stress (both in compression and tension) of aluminum and brass are 120 MPa and 180 MPa, respectively, determine the largest moment M that can be applied about the horizontal axis. 8 mm 8 mm - 32 mm 8 mm 32 mm 8 mm - Brass - Aluminum Duoblesna 1
Three aluminum rods support the rigid L-shaped bracket BCF as shown in the figure. Determine the stress in rod DE (express answer in MPa) if rod FG is cooled by 50°C. All three rods have the same cross-sectional area of 1000 mm^2. Use 73.1 GPa and 23 x 10^-6/°C for the modulus of elasticity and the coefficient of thermal expansion of aluminum, respectively.
A vibration isolation support consists of a rod A of radius R₁ and a tube B of inner radius R₂ bonded to an 80-mm-long hollow rubber cylinder with a modulus of rigidity G = 10.93 MPa. Determine the required value of the ratio R2/R1 if a force P = 13 kN is to cause a 2-mm deformation of rod A. B R₁ R₂ .. 80 mm The required value of the ratio R2/R₁ is 1.422
Question # 4: Determine the state of stress at point A on the cross section of the beam at section a-a. Show the results in a differential element at the point. a a 0.5m 0.5m 30 kN 2 m 100mm 50mm A 10mm 10mm 180mm Section a-a 10mm