The state of strain at a point on a wrench has components ϵx = 120(10-6), ϵy = -180(10-6), γxy= 150(10-6). Use Mohr's circle to solve the problem. Determine the orientations of the element at which the principal strains occur. θp1= θp2=

Q: The strain at point A on the bracket has components P x = 300(10-6 ), Py = 550(10-6 ), gxy =…

A: Given data

Q: The force applied at the handle of the rigid lever causes the lever to rotate clockwise about the…

A:

Q: The strain components εx, εy, and γxy are given for a point in a body subjected to plane strain.…

A: Given : εx = -1100 με εy = 490 με γxy = 1500 μrad θ  = 34°

Q: a3) Determine the shear strain at corner D and the normal strain of the diagonal CA if the shape is…

A: Shear strain is the strain caused due to the applied force in the longitudinal direction.

Q: The state of strain at the point on the spanner wrench has components of Px = 260(10-6), P y =…

A: Given data: Normal strain in x direction, εx = 260 x 10-6 Normal strain in y direction, εy = 320 x…

Q: The rod has a circular cross-section with a moment of inertia I. If a vertical force P is applied at…

A: Given data: The moment of inertia of the rod is I. The modulus of elasticity of the rod is E.…

Q: The rubber band AB has an unstretched length of 1m. If it is fixed at B and attached to the surfaced…

A:

Q: A rod has a radius of 10 mm. If it is subjected to an axial load of 15 N such that the axial strain…

A: Given: The radius of the rod is R=10 mm The axial load on the rod is FX=15 N The axial strain in the…

Q: A specimen consists of a rigid member CBD and a flexible cable AB. A: Determine the normal strain in…

A:

Q: The polysulfone block is glued at its top and bottom to the rigid plates. If a tangential force,…

A: GIVEN :-y=3.56x14TO DETERMINE :-the shear strain at the corners A and B,

Q: The force applied at the handle of the rigid lever causes the lever to rotate clockwise about the…

A: for pt B  BD = AB*tan2o        = 3*0.0349        = 0.1047 m normal strain in wire BD will be

Q: The steel shaft has a radius of 15 mm. Determine the torque T in the shaft if the two strain gages,…

A: Write the given data:

Q: The strain gage is placed on the surface of the steel boiler as shown. If it is 0.5 in. long,…

A: Given data: Surface of the steel boiler l = 0.5 in. Elongation of gauge, Δl = 0.2 x 10-3 in. Boiler…

Q: Q4) The 60° strain rosette is mounted on a beam. The following readings are obtained from each…

A:

Q: The 60o strain rosette is mounted on the surface of the bracket. The following readings are obtained…

A:

Q: Determine the shear strain gxy at corners D and C if the plastic distorts as shown by the dashed…

A: The FBD of the system is as follows:

Q: The distributed loading is applied to the rigid beam, which is supported by the three bars. Each bar…

A: Due to the distributed load the bars will experience equal force. Let the force in each bar be F.…

Q: F7-25. When force P is applied to the rigid arm ABC, point B displaces vertically downward through a…

A: The normal strain of the wire CD = change in the length of wired CD/Initial length of CD. The given…

Q: The A-36 steel bar consists of two segments, one ofcircular cross section of radius r, and one of…

A: The strain energy stored in circular section,

Q: 7-77. The wire AB is unstretched when e-45°. If a load is applied to the bar AC, which causes e to…

A: Given data: The angle of wire is θ = 47°. The unstretched length of wire is, Increased in length of…

Q: *2-4. The two wires are connected together at A. If the force P causes point A to be displaced…

A: CA=AB=300 mm In the right angle ∆AA"A' cos30°=A'A"2A'A"=1.732 mm

Q: If the normal strain is defined in reference to the final length Δs′, that is,P= = lim Δs′S 0 aΔs′ -…

A: Given ε'=lim∆s→0∆s'-∆s∆s'

Q: The strain at point A on the bracket has normal components 250x10-6 and 550x10-6 in x and y…

A:

Q: If the force P causes the rigid arm ABC to rotate clockwise about pin A through an angle of 0.02°,…

A: Given data: Rotated angle, θ = 0.020 Drawing the rotation of the arm ABC: here, δB = displacement…

Q: The bolt has a diameter of 10 mm, and the arm AB has a rectangular cross section that is 12 mm wide…

A: Diameter of bolt, d=10 mm,Cross section of rectangular plate, A=12 mm× 7 mmTension in the bolt,…

Q: Part of a control linkage for an airplane consists of a rigid member CB and a flexible cable AB. If…

A: Given Data∆AB=0.00317 mm AC=600mm BC=800mm

Q: A square piece of material is deformed into the dashed position. -15.18 mm В 15.24 mm 15 mm 89.7° A-…

A: Shear strain and average normal strain diagonal AC.

Q: The state of strain at the point on the support has components of ex = 350( 10-), ey = 400( 10-6),…

A: Given Data:- εx=350×10-6εy=400×10-6γxy=-675×10-6 To- Find:- a) In-Plane Principal Strains b) Maximum…

Q: he center portion of the rubber balloon has a diameter of d 100 mm. If the air lessure within it…

A: Given data : original diameter=100 mmfinal diameter=125 mm

Q: The triangular plate is fixed at its base, and its apex A is given a horizontal displacement of 5…

A: The diagram of the triangular plate is given as,       The distance OA is written as,…

Q: The strain at point A on the bracket has normal components 300x10-6 and 550x10-6 in x and y…

A:

Q: The state of strain on an element has components εx=−270(10−6)εx=−270(10−6),…

A:

Q: 10-9. The state of strain at the point has components of e, = 180(10“ ), e, = -120(10“), and y,y =…

A: Given: The strain along x-direction, εx = 180x10-6 The strain along y-direction, εy = -120x10-6 The…

Q: The state of plane strain on the element is e̟ = -300(10-°), €y = 0, and Yy = 150(10-°). Determine…

A: Given Data ex=-300(10-6)   ey=0    Yxy=150(10-6) Ans(A) Relation between the component of state of…

Q: 7- The state of strain at the point has components in the X-axis = -210x10-6, in the y-axis =…

A:

Q: The bar DA is rigid and is originally held in the horizontal position when the weight W is supported…

A: First, draw the free body diagram of the system: Use the proportion to evaluate the value of δED:…

Q: A sheet of copper is stretched biaxially in the xy-plane. If the strains in the sheet are e, = 0.40…

A: Stress in x-direction, σx = 63.3 MPa. Stress in y-direction, σy = 55.2 MPa.

Q: 1.The force applied at the handle of the rigid lever causes the lever to rotate clockwise about the…

A: Draw the diagram in that the lever is rotated by 2 degrees clockwise.

Q: PROBLEM 1. The state of strain at a point on an experimental aircraft wing has components, E. = 300…

A:

Q: The material distorts into the dashed position shown. Determine the average normal strains along…

A: Draw the schematic diagram of the given fig.

Q: The strain at point A on the bracket has normal components 750x106 and 150x106 in x and y…

A:

Q: The material distorts into the dashed position shown. Determine the average normal strains Px, Py…

A: Find out the normal strain in x-direction εx=A'F'-AFAF=150-150150=0 Find out the normal strain in…

Q: 6. Determine the lateral strain, in mm/mm, in the 5 mm diameter aluminum T6 rod when P = 8 kN. Use L…

A:

Q: The force applied at the handle of the rigid lever causes thelever to rotate clockwise about the pin…

A:

Q: Question 1: The state of strain at the point on the pin leaf has components of Ex = 200(106), E =…

A: Write the given data. εx=200×10-6εy=180×10-6γxy=-300×10-6 Calculate the principle strains.…

Q: The strain components e x, e y, and γ xy are given for a point in a body subjected to plane strain.…

A:

Q: (a) Determine the shear strain at corner A if the plate distorts as shown by the dashed line. (b)…

A:

Q: Q3- a) Determine the shear strain yxy at corners D, (Y,), if the defamation is shown by the dashed…

A: Solution: