The space between two parallel plates is filled with oil. Each side of the plate is 60 cm. the thickness of oil film is 12.5 mm. The upper plate, which moves at 2.5 metre per sec requires a force of 98.1 N to maintain the Speed. Determine

The space between two parallel plates is filled with oil. Each side of the plate is 60 cm. the thickness of oil film is 12.5 mm. The upper plate, which moves at 2.5 metre per sec requires a force of 98.1 N to maintain the Speed. Determine

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Can anyone answer this?
A water tank is being towed on an uphill road that makes an angle of 14 deg with the horizontal with constant acceleration of 3.5 m/s^2 in the direction of motion. Determine the angle the free surface of water makes with the horizontal. ( With Free Body Diagram)
The space between two flat plates is filled with oil .Each plate has 60cm x 40 cm x 10 cm) and the oil film thickness is 1 mm. When the plate are inclined 60° to the horizontal as shown in fig.(1). Find the velocity of the upper plate? The relative density of the upper plate is 50 and the angular deformation of fluid is 500 1/s.
The 25-cm diameter ram in a hydraulic lift slides in a 25.015-cm diameter cylinder. The viscosity of the oil filling the gap is 0.04 N⋅s/m2. If the speed of the ram is 15 cm/s, determine the frictional resistance force when a 3 m length of the ram is engaged in the cylinder. The answer provided is Fshear ressistance = 188N I just can not seem to figure this out please help.
5.Some oil is full of the space by two parallel plates. The lower plate is stationary, while the upper one moves parallel to it with a velocity U=2.5m/s due to a force F=98.1N corresponding to a square with length L= 60cm. h=12.5mm. Determine the dynamic viscosity of oil. y → U > F h
2. Cylindirical cup below is open at its top and totally filled with water. It is rotated with a contant angular velocity = 36.5 rad/s. Calculate volume and depth of water retained in the cup after this rotation. Hint: Volume of paraboloid is equal to the half volume of a cylinder with the same height. 0.4 m 0 0.08 m M X @₂=0
Two plates are separated by 30 mm space. The lower plate moves at velocity of 2 m/s while the upper plate moves at a velocity of 8 m/s. Oil (S=0.48) which fills the space. The oil viscosity is equal to 0.003 m Is. The variation in velocity of the oil is linear. What is the shear stress in the oil (N/m2)? upper plate -8 m/s OIL 30 mm 2 m/s lower plate ENG LIS
Spaces h1=15 mm and h2=20 mm wide between upper and lower stationary plates and a very thin moving plate is filled with crude oil (oil =7.18x10-3 Pas) and water (water =1.00x10-3 Pas), respectively. What force is required to drag the plate of 0.5 m2 area between the surfaces at a speed of v=0.15 m/s. Assume linear velocity profile
The water level in the 1.8 m high and 1 m diameter cylindrical tank in the figure is 1.4 m. If this tank is rotated around its own axis at what speed will the axial depth be zero? (In other words, what is the number of revolutions at which a dry area will begin to form at the bottom of the tank?) Take the gravitational acceleration as 10 m / s2 and π as 3.
Throughout, take the acceleration due to gravity to be 10 m/s? and water to have density of 1000 kg/m³. Question 1 A large block of mass 1100 kg is towed at a constant speed UB up an inclined plane at 6° to the horizontal, as shown in Fig. 1. The towing force applied on the block has magnitude 1165 N. The block slides over an oil film with a constant thickness of 3 mm. The oil has density 900 kg/m and dynamic viscosity 0.1 Pa.s. The area of the block in contact with the oil is 15 m2. UB F=1165 N m=1100 kg oil film 3 mm contact area: 15 m² 6° Figure 1 (i) Sketch, with appropriate labels, the forces acting on the block in the direction parallel to the inclined plane. (ii) Determine the magnitude of the drag force acting on the bottom surface of the block. (iii) Assuming a laminar velocity profile in the oil film, determine the speed of the block Ug. (iv) Verify that the flow of oil is laminar as assumed in (iii). (v) Determine the power requirement to tow the block. (vi) To reduce the…
The minimum pressure on an object moving horizontally in water (Ttemperatu at10 degree centrigrade) at (48 + 5) mm/s, at a depth of 1 m is 80 kPa (absolute). Calculate the velocity that will initiate cavitation. Assume the atmospheric pressure as 100 kPa (absolute).
What is the pressure at the bottom of 0.5m height fluid if the container moves 5m/s2 upward? Fluid has a density of 2000kg/m3 a. 13665Pab. 13258Pac. 14810Pad. 16145Pa