The solid steel rod (1) has an allowable shear stress of 13 ksi. The brass tube (2) has an allowable shear stress of 5 ksi. The diameter of the rod is d₁ = 0.500 in. The outside diameter of the tube is D₂ = 1.750 in., and its wall thickness is t₂ = 0.125 in. The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at B. Determine the largest torque Tmax that can be applied at the upper end of the steel rod. Rod (1) Tube (2) B D₂ Answer: Tmax = i Fixed plate End plate lb-in.

The solid steel rod (1) has an allowable shear stress of 13 ksi. The brass tube (2) has an allowable shear stress of 5 ksi. The diameter of the rod is d₁ = 0.500 in. The outside diameter of the tube is D₂ = 1.750 in., and its wall thickness is t₂ = 0.125 in. The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at B. Determine the largest torque Tmax that can be applied at the upper end of the steel rod. Rod (1) Tube (2) B D₂ Answer: Tmax = i Fixed plate End plate lb-in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An axial element that is subjected to force P is connected by two plates and 4 bolts as shown in the figure. The ultimate shear stress of the pins is τy = 21 ksi. The pins diameter is d = 1.25 in. The factor of safety is 1.64 .Determine the maximum allowable force (P) that can be applied to the following connection. An axial element that is subjected to force P is connected by two plates and 4 bolts as shown in the figure. The ultimate shear stress of the pins is τy = 21 ksi. The pins diameter is d = 1.25 in. The factor of safety is 1.64 .Determine the maximum allowable force (P) that can be applied to the following connection. Using the equation FS=T failure/T actual
B2
Two bars are connected with a welded butt joint as shown. The bar dimensions are b = 200 mm and t = 50 mm, and the angle of the weld is a = 45°. The bars transmit a force of P = 301 kN. What is the magnitude of the average shear stress that acts on plane AB? Weld В P A Answer: T= i MPа
Include the FBD of the Problem
ll ? The rod BD is made of material with G1= 135 GPa has a diameter 16 mm is bonded to the tube CA at point B, the tube made of material with G2=230o GPa has an outer diameter 37 mm and wall thickness of 7 mm. li T1=803 N.m and T2=1445 N.m, answer the following questions: B T2 Nm 04 m 0.1 m 0.3 m TI N-m The polar moment of inertia of the rod BD is Your answer The polar moment of inertia of the tube CA is
The copper pipe [G = 6,000 ksi] has an outside diameter of 3.375 in. and a wall thickness of 0.250 in. The pipe is subjected to a uniformly distributed torque of t = 85 lb-ft/ft along its entire length. Using a = 2.5 ft, b = 3.5 ft, and c =7.0 ft, determine (a) the maximum shear stress in the pipe. (b) the rotation angle pc at the free end of the shaft. b B C Answers: (a) Tmax psi i rad (b) ¤c = i
strictly don't copy the answer
How did it solve the rivets? Kindly explain it with solution
The principal strains at a point on the aluminum surface of a tank are P1 = 630(10-6) and P2 = 350(10-6). If this is a case of plane stress, determine the associated principal stresses at the point in the same plane. Eal = 10(103) ksi,nal = 0.33.
Tind the stresses in the steel and aluminum rods when the temperature rises to 60 C° and the distributed load is 10 kN/m. Given: Steel Rod E = 200 GPa L = 1.499 m 10KN/m esmott A = 80 mm? oc= 12 x 10-6 1/°c Gap 1 mm Aluminum Rod Steel Rod Aluminum Rod E = 70 GPa L = 1.5 m A = 200 mm? x= 22 x 10-6 1/°c Figure (2) !! 2 m 2 m
O d. NA = 0.374 , Ng = 2.611 Clear my choice The pipe assembly shown is subjected to a force F = 12 kN and P = 6 kN. It is made of steel with Sy = 250 MPa. Determine the safety factor at point H using the maximum shear stress theory. 1.2 m 0.65 m d= 176 mnm D- 200 mm Cross section Select one: O a. NH =4.07 360=5355 Od.N-8576 solid rounc bar deep wich a 2 5-mm radiu 1:14 AM fla )) ENG 22/4/2021
How many 8-mm diameter rivets is needed to fasten member DC to the gusset plate at Cif the member DC has thickness of 8 mm and the working stresses are 15 MPa for shear in the rivets and 20 MPa for bearing due to the rivets. Express your answer to the nearest whole number being the safe value of the rivets to be used. * Sm 40 RN 35 AN