Answered: The size of square footing required to…

The size of square footing required to carry a load of 30000 kg-f using Terzaghi's method is 30000 kg-f p- 1850 kg/m' - 35° C=0 N = 57.8, N, = 41.4 N,- 42.4, FOS = 3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1. For the truss shown below, determine the minimum cross-sectional area in bars BD, CD, and CE if t...

Q: Determine the resultant (in newton) of the forces acting on the pin as shown in the figure if the fo...

A: Determine resultant,R=?

Q: A wood cone, 700 mm diameter and 1000 mm high floats in water with its vertex down. If the specific ...

Q: Q: Find the reactions of the beam shown 36 kN 52 kN 35 kN/m E B 150 kN-m 3 m 3 m 3 m 6 m

A: Given, A beam, Length= L= 15m Two point loads= 52kn, and 36kn Free body diagram of beam:-

Q: Determine the moment of the 210-lb force about polnt A and about point O. 37" 24" 40 F- 210 lb

A: This question is related to the Engineering Mechanics.

Q: 4.0 N force is applied as shown in the figure below. Find the torque produced by this force with res...

Q: 1.) If the specific weight of a liquid is 7000 N/m3, what is its mass density? 2.) If 300 ft3 of oi...

Q: Properties of T-Section Br = 180 mm T= 16 mm Tw = 12 mm D = 210 mm Properties of C-Section Br = 105 ...

Q: 8 KN 15 KN/m 12 KN/m A E 2m 3m 3m 2m

Q: cantiliver shown in the diagram has a length L1=9 m and subjected to a uniformly distributed load q2...

Q: please show complete solution and fbd

A: Cable: - It is defined as flexible structures which are used to support transverse loads due to whic...

Q: In raising the 52-m pole from the position shown, the tension Tin the cable must supply a moment abo...

A: This question is related to the Engineering Mechanics from Civil Engineering.

Q: The lower lumbar region A of the spine is the part of the spinal column most susceptible to abuse wh...

Q: For a given section of road, relationship between speed and density is obtained asu = 53 – 0.43 k, w...

Q: Find the Normal Stresses experienced by the Steel, Aluminum, and Bronze section of the given body. T...

Q: difference in elevation between points at designated short measured intervals along an estableshed l...

A: Differential leveling

Q: Question 26 of 46 While digging a small hole prior to planting a tree, a homeowner encounters rocks....

Q: An experimental device imparts a force of magnitude F = 67 lb to the front edge of the rim at A to s...

Q: At Q = 2000 gpm: = head provided by pump 1 = 75 ft H2 = head provided by pump 2 = 125 ft ni = effici...

Q: If the longitudinal main reinforcement in beam used is D-16 mm, the size of stirrup should be

Q: To close a gate valve it is necessary to exert two forces of 60 lb at opposite sides of a handwheel ...

A: Given data, Handwheel diameter = 3 ft Force = 60 lb Bar length = 4 ft To draw FBD and force require...

Q: Determine the moment of P about point B and about point

Q: 8 KN 15 KN/m 12 KN/m A E 2m 3m 3m 2m Properties of T-Section Br = 180 mm T= 16 mm Tw = 12 mm D = 210...

Q: A steel rod, circular in cross-section, tapers from 30 mm diameter to 15 mm diameter over a length o...

Q: Determine the equivalent state of stress on an element if it is oriented 30° clockwise from the elem...

A: Given data - The element is oriented 30* We have to use stress transformation equation and Tu = 900 ...

Q: 6.) A quart of a certain fluid weighs about

A: Given mass=3.25slugsV=1ft3so,Specific weigth =WV=3.25slugs×32.21=104.65lbft3

Q: Problems 6-7: Use the SCS (soil conservation service) curve number (CN) handout Given a 7 mi fully p...

Q: Determine the tension in each of the three ropes supporting the crate. Z. 2 ft 4 ft y 1.6 ft В 4 ft ...

Q: A man exerts a force Fon the handle of the stationary wheelbarrow at A. The weight of the wheelbarro...

Q: I. Problem Solving. Box your final answer. 1. Find the (a) maximum tensile and compressive bending s...

Q: (a) Determine the total and effective principal stresses. (b) Recommend the shear strength parameter...

Q: Item 2 Determine o". Determine the equivalent state of stress on an element if it is oriented 30° Ex...

A: Given - To find -

Q: Determine the magnitude of the resultant force in kilonewton. F1 = 907 N F2 = 1,253 N F3 = 981 N 01 ...

A: Given : F1 = 907 NF2 = 1253 NF3 = 981 Nθ1 = 48°x...

Q: A spherical tank with 10 inches inside diameter contains oxygen gas at 2,500 psi. Calculate the requ...

A: Inner diametr of spherical tank, d =10 inchesPressure of oxygen gas, P =2500 psiAllowable stress, σ ...

Q: A saturated compressible clay layer of thickness h is sandwiched between two sand layers, as shown i...

A: Given-Thickness of clay layer=hpore water pressure, u=25 kPavertical stress,σ=150 kPaadditional vert...

Q: (a) Draw the Mohr circle that describes the 2D stress state and find the maximum shear stress that a...

Q: From the system of forces shown in Figure. Each square is 1 ft. on a side. a. Determine the resultan...

Q: TRAIN PROBLEMS S=D TYPE 9, TD FORMULAI A tnain (s 20om long om long. rins at 50m/s. Find t?

A: Introduction : The given question is related with mechanics topic . In this question we are provided...

Q: A cylindrical piece of steel 80 mm dia and 120 mm long is subjected to an axial compressive force of...

A: As per the question , Axial force=50000kg So in the cylindrical piece strain will develop because of...

Q: Determine the force P required to maintain the 205-kg engine in the position for which @=36° The dia...

Q: Determine the magnitude Pof the vertical force required to lift the wheelbarrow free of the ground a...

Q: The following are the moments acting on a structural member. The limiting moment (in kNm) for collap...

A: Given data, to find the limiting moment for collapse condition

Q: A man exerts a force F on the handle of the stationary wheelbarrow at A. The weight of the wheelbarr...

Q: Calculate the amount of soil that need to be excavated for wall footing that has a depth of (h). Foo...

A: Que:- Calculate the amount of soil that needs to be excavated for wall footing that has a depth of (...

Q: For a colony of 10000 persons having sewage flow rate of 200 1/capita/day, BOD of applied sewage is ...

Q: Discuss ductile detailing for columns subjected to bending and axial loads as per IS: 13920 specific...

A: Solution: Ductile Detailing for columns subjected to Bending and axial load As per IS:13920 The req...

Q: A wastewater treatment plant processes its mixed sludge by employing the gravity thickening followed...

A: Hazen William equation for Head loss due to friction in a pipeline hf=10.67*Q1.852*LC1.852*d4.8704 F...

Q: A simple circular curve has a radius of 300 m and 60° deflection angle. Compute the following: a. it...

A: Given, Radius of the curve= R= 300m, Deflection angle= ∆= 60° Note :- as per our company gui...

Q: 2 m 1.5m

A: P=40kN to find stress in rod A and elongation in rod B

Q: a circular curve is to be constructed with a 225 ft radius and an interior angle of 55 degree. deter...

A: Given - Radius of circular curve = 225 ft Interior angle = 55 degree The separation between the st...

Concept explainers

Load and resistance factor design

Load and resistance factors design (LRFD), also known as Limit state design (LSD), refers to the design method used in building engineering. A boundary condition is a condition of a structure where it can no longer meet the relevant design requirements. The condition may refer to the load level or other actions on the structure, while the terms refer to the integrity of the structure, suitability for use, durability, or other design requirements. A structure designed for LRFD is limited to keeping track of all possible actions during its design time and is always ready for use, with the appropriate level of reliability in each boundary condition. LRFD-based construction codes clearly define the appropriate levels of reliability in their instructions.

Question

The size of square footing required to carry a load of 30000 kg-f using Terzaghi's method is
30000 kg-f
p= 1850 kg/m'
O = 35°
C= 0
N = 57.8, N, = 41.4
N, = 42.4, FOS = 3
d =1 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A rectangular footing has dimensions shown and is acted upon by a dead load of 570.00 kN and a live load of 621.00 kN. The column dimension is 366x576 mm where the shorter dimension is parallel to B. The thickness of the footing is 476mm. f'c=28 MPa and fy=420 MPa for diameter 20mm bars. A=2.5m and B=4.5m Calculate the ratio of the Ultimate Shear Force to Shear Capacity in two- way shear. Answer is 0.9238 (Complete Solution)
A rectangular footing has a dimensions shown and is acted upon by a dead load of 722 kN and a live load of 620 kN. The column dimension is 326 x 662 mm where he shorter dimension is parallel to B The thickness of the footing is 408mm. f'c=28 MPa and fy=420 MPa for diameter 20mm bars. A=3.1m and B=5.1m
A rectangular footing has dimensions shown and is acted upon by a dead load of 382 kN and a live load of 536 kN. The column dimension is 307x560 mm where the shorter dimension is parallel to B. The thickness of the footing is 656mm. fc=28 MPa and fy=420 MPa for diameter 20mm bars. A=2.6m and B=5.2m
A 4.7 m square footing is proposed to be used to support a 635 mm x 635 mm RC column loaded with 665 kN dead load and 843 kN live load. The bottom of the footing is 2 m below the ground. Assume soil weighs 19 kN/m3 and the allowable soil bearing pressure is 331 kPa. The thickness of the footing is 462 mm. f'c = 21 MPa and fy = 420 MPa. It is to be reinforced with 20 mm diameter. Use 24 kN/m³ as the unit weight of concrete. Use an effective depth measured from the top of the footing until the center of the bottom-most bar Calculate the number of bars required in one direction. Provisions are given below for the minimum area of main reinforcements Reinforcement Type fy. MPa As.min. mm² Deformed Bars 420 MPa Reinforcement Greater of: 0.0018×420 f₂ 0.0014A -A₂
A square footing has the following properties. The footing will carry a gross load of 60,000lb. Using factor of safety of 3.0, determine the size of the footing. (answer3.25’)Given: ∂ = 110 pcf Df = 2ftc = 0 B = 3.0 ftØ = 350 FS = 4.0
A rectangular footing has dimensions shown and is acted upon by a dead load of 584 kN and a live load of 412 kN. The column dimension is 399x719 mm where the shorter dimension is parallel to B. The thickness of the footing is 696mm. fc=28 MPa and fy=420 MPa for diameter 20mm bars. A=2.8m and B=5.7m Calculate the number of bars along the long direction
A 3.2 m square footing is proposed to be used to support a 373 mm x 605 mm RC column loaded with 637 kN dead load and 856 kN live load. The bottom of the footing is 1.7 m below the ground. Assume soil weighs 19 kN/m3 and the allowable soil bearing pressure is 343 kPa. The thickness of the footing is 464 mm. fc = 21 MPa and fy = 420 MPa. It is to be reinforced with 20 mm diameter. Use 24 kN/m³ as the unit weight of concrete. Note: For two-way shear, use an effective depth measured from the top of the footing until the top of the bottom-most bar (d3) What is the ratio of the Demand Shear Force and the Capacity in Two Way Shear? (Vu/phiVn) Answer in 4 decimal places (1.6125, 1.5140, 0.8461, etc.) You Answered Correct Answer 1.3809 margin of error +/- 1%
3. A square footing that carries an axial load of 150000kg has its bottom resting on a ground water table at a depth of 2.5m from the ground surface. Take PDRY = 1860kg/m3 and PSAT = 1950kg/m3, c = 1600kg/m2, ø = 30degrees. Use the approximate formulas for the determination of the bearing capacity factors. a.Compute the required width of the footing using a factor of safety of 2. b.Compute the ultimate bearing capacity of the soil. c.Compute the net factor of safety. d.Compute the net soil pressure.
A rectangular footing has dimensions shown and is acted upon by a dead load of 1200 kN and a live load of 1600 kN. The column dimensions is 300x600 where the shorter dimension is parallel to B. The thickness of the footing is 500mm. f'c = 28 MPa and fy = 420 MPa for diameter 20mm bars. A = 2.4m and B = 4.2m Calculate the Following: A.) Critical Ultimate Shear Strength and Shear Force of the footing for beam shear action, kNB.) Critical wide beam nominal shear stress, MPaC.) Ultimate Shear Strength of the footing in punching shear action, kN Please answer it ASAP and correctly for upvotes.
A rectangular footing is designed to carry an allowable load of 580kN with its weight inclusive. The bottom of the footing is 1m below the ground surface and the water table coincides with the bottom of the footing. Assume general shear failure. Given, γ=18kN/m^3, c = 25kPa, γ_sat=21.5kN/m^3. Use Nc = 35, Nq = 22, Ny = 19. Determine the width B of the footing using FS = 3.0 if B/L = 0.5
2) A square footing carries an allowable load of 59130kg including its own weight. The bottom of footing is 1.0m below ground surface and water table coincide with bottom of footing. Assume General shear failure. Unit Weight = 1846kg/cu.m c= 1605kg/sqm Nc = 35 Nq=22 Ny=19 1.0m Sat unit wt = 1956kg/cu.m
A rectangular footing has dimensions shown and is acted upon by a dead load of 653 KN and a live load of 647 kN. The column dimension is 269x677 mm where the shorter dimension is parallel to B. The thickness of the footing is 442mm. f'c=28 MPa and fy=420 MPa for diameter 20mm bars. A=2.9m and B=4.8m Calculate the ratio of the Ultimate Shear Force to Shear Capacity in one-way shear. Consider critical case only.