The single stage, axial flow turbomachine shown in figure 3 involves water flow at a volumetric flowrate of 14m³/s .The rotor revolves at 600 rpm. The inner and outer radial of the annular Flow path throug the stage are 0.46 and 0.61 m, and B2=25°. The flow entering the rotor row and leaving the stator row is axial viewed from the stationary casing. Is this device a turbuine or a pump? Estimate the amount of power transferred to or from the fluid. [M Rotor ,Stator Q=14 m³ /S U2 fo=0.61 m 0.46 m 600 rpm

The single stage, axial flow turbomachine shown in figure 3 involves water flow at a volumetric flowrate of 14m³/s .The rotor revolves at 600 rpm. The inner and outer radial of the annular Flow path throug the stage are 0.46 and 0.61 m, and B2=25°. The flow entering the rotor row and leaving the stator row is axial viewed from the stationary casing. Is this device a turbuine or a pump? Estimate the amount of power transferred to or from the fluid. [M Rotor ,Stator Q=14 m³ /S U2 fo=0.61 m 0.46 m 600 rpm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4. A bladed fan rotor with an outside diameter of 12 in. and a 5 in. inside diameter runs at 1725 rpm. The width of each rotor blade is 1 in., from the blade inlet to outlet. The volume flow rate is steady at 230 ft/min. and the absolute velocity of the air at the blade inlet is purely radial, V₁. The blade discharge angle at the outlet is 30° as shown. (a) What would be a reasonable blade inlet angle, and (b) what is the power required to run the fan. (Pair = 2.38 × 10-3slugs ft3 309 1725 rpm 12 in. Q-230 ft/min
1 The internal and external diameters of the impeller of a centrifugal pump are 200 mm and 400 mm respectively. The pump is running at 1200 rpm. Forward blades make an angle of 150o at exit and at inlet the angle is 20o. The blade thicknesses at the inlet and outlet are 100mm and 70mm respectively. The hydraulic efficiency of the pump is 87%. Assume the water enters the impeller radially. i Draw neatly the outlet velocity diagram and the inlet velocity diagram. ii Find the Euler power of the pump. iii Find the net Head of the pump. Ans: (ii)140.65W; (iii) 43.42m
Q3// the steam from the nozzle of single wheel impulse turbine discharges with velocity of 600 m/s at angle of 20°. The blade wheel rotates at 3000 rev/min and the mean blade radius is 590mm. the axial velocity of steam at exit from the blade (f.) is 164 m/s and the blades are symmetrical, calculate for 1 kg/s of steam: 1. The blades angles. 2. The blade power. 3. The blade efficiency. 4. The blade velocity coefficient. Answer (28°,126.3 kW, 70% ,0.799)
3. A centrifugal pump impeller runs at 1400 rpm, and vanes angle at exit is 25 degrees. The tangential velocity at exit is 29.33 m/s. Whirl velocity at impeller tip is 23.75 m/s. The impeller has an internal diameter of 0.2 m. Assuming a constant radial flow through the impeller at 2.6 m/s. Calculate: a. The vanes angle at exit b. The angle made by the absolute velocity of water at exit with tangent c. The inlet vane angle d. The work done per kg of water e. Draw the velocity triangle of the system f. Find the impeller external diameter
The first compressor blade pair in a turbojet is to be designed with symmetric blading. If the inflow to the compressor has a gas speed measured as 108m/s, for this speed the shaft is designed to rotate at 262rad/s, and the mean blade radius of this first blade row is 0.51m, to what angle should the first stator be set? Express your answer in degrees.
2. A wind turbine has the maximum power output at the rated speed of 12 m/s and a rotor diameter of 82 meters. The cut-in and cut-out speeds for this type of wind turbine are 4 m/s and 23 m/s, respectively. The table below shows the annual wind data near a potential site for setting up a wind farm using this type of wind turbine and the power coefficient of the wind turbine at the specific wind speed. The air density is 1.22 kg/m³. Wind speed (m/s) Power coefficient 7 Hours 1190 5 0.25 3000 10 0.5 2400 15 0.25 1700 20 0.1 400 25 50 30 20 (a). What is the maximum power output of this wind turbine, assuming Betz limit? (b). What is the average power output if the wind turbine is installed at this site?. (c). What is the capacity factor of the wind turbine at this site? (d). If a wind farm consisting of 100 such wind turbines is built at the site, how much energy does this wind farm generate in a year (in the unit of kWh)? (e). Is this a good site for using this particular type of wind…
3. A centrifugal pump has d1 = 7 in., d2 = 13 in., b1 = 4 in., b2 = 3 in., 1 = 25, 2 = 40 and rotates at 1160 rev/min. If the fluid is gasoline at 20C and the flow enters the blades radially, Estimate the theoretical (a) flow rate, in gpm; (b) the water horsepower; and (c) the head in ft. b. flow rate Answer : _______________ gpmc. water horsepower Answer : _______________ HPd. head Answer : _______________ ft
Q3.A Francis turbine has the dimensions of r=1.42 m, r,=2.00 m br=2.20 m and by=0.731m. Rotation speed of the turbine is 180 rpm. Three angles of velocities at the inlet and outled of the blade are defined as oaz= 35° and al=25° The flow rate of turbine is 340 m/s and the total head of the turbine is 80 m. Neglecting losses, www a) Draw the velocity three anges at inlet and outlet of the blade. b) Calculate blade angles at inlet and outlet of the blade, Power. Net head of turbine. c) Losses in water channel (Penstock). Note: Point (2) presents inlet and while point (1) presents outlet section of blade. Adjustable guide vane Blade n
A pump draws water from open reservoir A at 20 ft above pump centerline and lifts to an open reservoir B at 280 ft above pump centerline. The loss of head at the suction is 3 times the velocity head at the 6 inches suction pipe and at the discharge is 20 times the velocity head at the 4 inches discharge pipe. The pump discharge is 200 GPM. a. The total dynamic head in ft. b. The water power in horsepower
Q1): Impulse turbine diameter = 3.2m O1 = O2 Angular velocity = 25 rad/s Absolute velocities V1 = 140m/s and V2 = 110m/s Power developed by the wheel = 300kw Calculate: Jet 25mmd VI V: 1. the blade velocity. 2. the force exerted and 3. the angle O.
In a medical water treatment station, there is a centrifugal pump. The pump delivers a flow rate of 0.003 m3/s. The pump radius is 0.3 m. The water enters axially and leaves the impeller relative to radial blades at the exit. Theoretically using Euler turbomachine equation, what should be the rotation speed for the pump to develop a head of 9 mH2O? Give your answer in rotation per minutė (rpm).
An inflow to a turbine with a discharge of 20 m³/s leads to a ration speed of 150 rpm. The blades inlet edges have an angle of 120° to the direction of whirl. The outer diameter of the runner is 1.5 m and the runner inlet width is 1.0 m. 5. (a) To plot the velocity triangle at the blade outlet edge. (b) Assume design operating conditions and no velocity of whirl at outlet, calculate the power delivered by the runner. (c) The elevation difference between the head race and the tail race is 23 m and the head available to the turbine is 20 m, what is the hydraulic efficiency of the turbine and overall efficiency? (d) If a model of 1/10 full scale is constructed to operate under a head of 10 m, what must be its speed, power, water consumption and overall efficiency to run under the similar conditions to the prototype?