The simple truss is loaded by a system of forces as shown in the figure. The truss is supported by a pin at D and a roiler at C. If P = 800 ib, then the force developed in the member (FE) is. I500 Ib 3ft FL 3 ft 3 ft E D 3 ft P. Select one: Oa 1200 lo -Tension 06 1000 b -Compression 2:2100 b-Tenson

Answered: Image /qna-images/answer/ec722c93-caa3-4aeb-a27e-97ab801f92cd.jpg

Answered: The simple truss is loaded by a system of forces as shown in the figure. The truss is supported by a pin at D and a roiler at C. If P = 800 ib, then the force…

Related questions

Question

The simple truss is loaded by a system of forces as shown in the figure. The truss is supported by a pin at D and a roller at C. IfP= 800 lb, then the force developed in the member (FE) is.
500 lb
3 ft
-3 ft-
E
DI
31-
3 ft
VP
Select one:
Oa 1200 ib- Tension
05 1000 16 - Compression
O C 2100 lb-Tension
Cd 1020 lb- Compression

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

See solution Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by stepSolved in 2 steps with 2 images

See solution

Check out a sample Q&A here

Knowledge Booster

Similar questions

A walkway suspended across a hotel lobby is supported at numerous points along its edges by a vertical cable above each point and a vertical column underneath. The steel cable is 1.27 cm in diameter and is 5.45 m long before loading. The aluminum column is a hollow cylinder with an inside diameter of 16.14 cm, an outside diameter of 16.24 cm, and unloaded length of 3.25 m. When the walkway exerts a load force of 8,400 N on one of the support points, how much does the point move down? mm
A woman is standing erect and with her elbow flexed 90°. She has an 80 N load in her hand and it has a 0.25 m lever arm to the elbow. Her biceps creates 800 N of force and it has a 0.02 m lever arm to the elbow. The type of contraction in the biceps is: Group of answer choices concentric isometric really big eccentric
WL is not 3580, and Fp is not 12000
Determine the force in member BE of the loaded truss. Enter a positive number if in tension, negative if in compression. 11' B 14' 15° 15° F E 11' 15° 1.0 L 1.7L 15° 45° A Answer: BE = i !L 45° D
Answer the following questions. 1. Calculate the elongation of the cable due to load, if a steel cable of 4cm diameter is used to lift a load of 350kg. Given that and the length of cable is 10m and E=3x10'kg/cm. 2. A tensile test was conducted on mild steel bar. The load at elastic limit was 200KN and the diameter of the steel bar was 3cm. What will be the value of stress? 3. A steel bar 600mm long and having 30mm diameter, is turned down to 25mm diameter for one fourth of its length. It is heated at 30 C above room temperature, clamped at both ends and then allowed to cool to room temperature. If the distance between the clamps is unchanged, the maximum stress in the bar ( a = 12.5 x 10" per C and E = 200 GN/m) is 4. Determine the yield stress of a steel rod 15 mm diameter, if the yield load on the steel rod is 70KN. 5. Where do the maximum BM occurs for the below diagram. 10 KN 2M OM
Draw the shear and bending-moment diagrams for the beam and loading shown and determine the maximum normal stress due to bending. 2 kN 1 m 3 kN/m 4 m 1 (for solid circle of radius c) = n/4 c B 140 mm TOT 160 mm
3. The center of gravity A В C D of the following structures is indicated by x. Which of the following structures is the most stable?
A single non-reinforced concrete column with a rectangular cross-section of 12.0 * 18.0 cm is used to support a large platform a) What is the maximum weight of the platform if we want to maintain a safety factor of at least 10.0? The ultimate compression strength of concrete is 172MPa b)If the column were to break under the weight, where would it most likely break, at the top or bottom?