The shaft in Figure below consists of a 3-in. -diameter aluminum segment that is rigidly joined to a 2-in. -diameter steel segment. The ends of the shaft are attached to rigid supports, Calculate the maximum shear stress developed in each segment when the torque T = 10 kip.in is applied. Use G=4×106 psi for aluminum and G = 12×106 psi for steel. Aluminum 3-in. diameter 6 ft T Steel 2-in. diameter 3 ft-

The shaft in Figure below consists of a 3-in. -diameter aluminum segment that is rigidly joined to a 2-in. -diameter steel segment. The ends of the shaft are attached to rigid supports, Calculate the maximum shear stress developed in each segment when the torque T = 10 kip.in is applied. Use G=4×106 psi for aluminum and G = 12×106 psi for steel. Aluminum 3-in. diameter 6 ft T Steel 2-in. diameter 3 ft-

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.11.5P: A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used...

See similar textbooks

Similar questions

A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
The propeller shaft of a large ship has an outside diameter 18 in. and inside diameter 12 in,, as shown in the figure. The shaft is rated for a maximum shear stress of 4500 psi. If the shaft is turning at 100 rpm, what is the maximum horsepower that can be transmitted without exceeding the allowable stress? If the rotational speed of the shaft is doubled but the power requirements remain unchanged, what happens to the shear stress in the shaft?
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
Solve the preceding problem for a W 200 × 41,7 shape with h = 166 mm, h = 205 mm. rw = 7.24 mm, tE= ILS mm,andV = 38 kN.
A plumber's valve wrench is used to replace valves in plumbing fixtures. A simplified model of the wrench (see figure part a) consists of pipe AB (length L. outer diameter D inner diameter dy), which is fixed at A and has holes of a diameter dhon either side of the pipe at B. A solid, cylindrical bar CBD (lengths, diameter^) is inserted into the holes at B and only one force F = 55 lb is applied in the -Z direction at C to loosen the fixture valve at A (see figure part c). Let G = 11,800 ksi, v = 0.30, L = 4 in., a = 4.5 in., d2= 1.25 in., dx= 1 in., and dh= 0.25 in. Find the state of plane stress on the top of the pipe near A (at coordinates A" = 0,Y = Q,Z = d->12), and show all stresses on a plane stress element (see figure part b). Compute the principal stresses and maximum shear stress, and show them on properly rotated stress elements
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 70 mm and G = 33.29 GPa. For the steel segment BC, the diameter is 40 mm and G = 84.85 GPa. Given that a = 2.03 m and b = 1.38 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 64.59 MPa in the bronze and 84.39 MPa in the steel. Round off the final answer to two decimal places. d A Bronze B Steel b. Add your answer
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 66 mm and G = 34.74 GPa. For the steel segment BC, the diameter is 45 mm and 6 = 84.1 GPa. Given that a = 2.18 m and b = 1.43 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 65.48 MPa in the bronze and 81.24 MPa in the steel. Round off the final answer to two decimal places. d ... A Bronze B Steel b–
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 74 mm and G = 33.05 GPa. For the steel segment BC, the diameter is 47 mm and G = 84.69 GPa. Given that a = 2.18 m and b = 1.33 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 60.08 MPa in the bronze and 82.03 MPa in the steel. Round off the final answer to two decimal places
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 68 mm and G = 34.84 GPa. For the steel segment BC, the diameter is 40 mm and G = 83.59 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 69.92 MPa in the bronze and 87.06 MPa in the steel. Round off the final answer to two decimal places. d ... A Bronze B Steel b.
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T in kN-m that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel. Answer in 2 decimal places