The shaft as shown in the figure is supported by bearings at A and B. The bearings exert only vertical reactions. The pulley wheel on the end of the shaft applies a vertical force F = 49.4 kN. What is the max bending moment in the shaft? Input your answer as a value only in kNm to one decimal place without +/-sign. 250 mm F 800 mm- B

The shaft as shown in the figure is supported by bearings at A and B. The bearings exert only vertical reactions. The pulley wheel on the end of the shaft applies a vertical force F = 49.4 kN. What is the max bending moment in the shaft? Input your answer as a value only in kNm to one decimal place without +/-sign. 250 mm F 800 mm- B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Choice the correct answer.
Buppose that A-00 KN. (Foure 1) Figure -20AN 10 1 of 1 Part A Determine the magnitude of the resultant force Express your answer to three significant figures and include the appropriate units. Pw- Bubmit Y Part B Value ()- Request Answer A Determine the direction of the resultant force, measured counterclockwise from the positive axi Express your answer using three significant figures. VAX i vec Pearson Units
Q3/ For the plate shown in figure below find * (a) ΣΑ YA 7 8 5 إجابتك
(b) The water is siphoned out of the tank shown in Figure 4 (b). Determine the flow rate from the tank and the pressures at points (1) and (2).
Select the correct statements regarding the addition of moments. (Select 3) Moments have directions, so a negative value implies it is along the opposite direction from the reference direction. All the moments need to have the same reference point/pivot in order to add together. Calculate each moment by multiplying each force with its distance to the reference point, and add all values together, regardless of their direction. You have to define the reference direction first, either clockwise or counter-clockwise.
Q.3) Determine Ixx and lyy for the composite section shown below. 50 mm 25 mm 30 mm 25 mm 50 mm 50 mm
How do you find the point of application?
1 The 45° strain rosette is mounted on a surface of the bracket as shown in Figure Ql. The bracket is made from steel with Eseel = 120 GPa and poison ratio, v = 0.28. The following readings are obtained for each gauge under loadings: Ea=[X+Y] (10*) Es = -200(10-6) E= -180(106) Important note : X=100 Y=60 (a) Prove that &=Ea and &= E,. (b) Determine the shear strain, y and the normal strain, &, and E,. (c) Estimate the in-plane principal strains and the angle associated with the principal strains, and
D= 1.75 in d= 0.75 in r= .120 in
(b) Find the natural frequencies and mode shapes. (c) Calculate the natural frequencies and mode shapes with m₁ = m2 = 2 kg and k₁ = k2 = 3000 N/m. You can just use the formula you obtained in (b).
8 the ban
Question 6 a) The bore of each cylinder in a six-cylinder car engine is 45 mm and the stroke for each piston is 125 mm. calculate the cubic capacity of the engine in cubic centimetres (cm³); and calculate the clearance volume per cylinder for a compression ratio, r, of 8.75. b) The bore of each cylinder in a four-cylinder four-stroke internal combustion engine is 38 mm and the stroke of each piston is 165 mm. During testing, the engine runs at 180 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 3.4 cm² and a diagram length of 1.2 cm. The pressure scale on the indictor diagram is set to 150 kN/m² per cm. Calculate the mean effective pressure (m.e.p) and the indicated power developed by this four-cylinder four-stroke engine. c) Figure Q6c shows a pulley system with a suspended load w of 2000 N. Calculate the following: (i) (ii) (iii) (iv) The effort force (FEffort) necessary to lift and hold a load of 2000 N. The ideal mechanical advantage…