The semicircular plate in the picture is 5 [ft] long and acts as a gate in a channel. The fluid is water. Calculate the reaction force on the gate from the smooth support at A ( FAz) in [N] or [kN]. Don't forget to convert [ft] to [m].

Q: What about Mohr's circle?

A: In the previous question, Given: The diameter of shaft, d = 20 mm = 0.02 m The maximum bending…

Q: Which among the following is a forming process in which thickness of the metal plate is decreased by…

A: Rolling: In this handle, the workpiece within the frame of slab or plate is compressed between two…

Q: Describe Pascal’s law?

A: Pascal’s law states that the static pressure acted on a liquid particle at rest is normally towards…

Q: What is the part’s over all length?_______________________ 6. Whatisthe part’s over all…

A: considering the detailed drawing of an object to find out the answers of the given questions.

Q: Which among the following is a forming process in which thickness of the metal plate is decreased by…

A: Metal forming processes are the processes in which plastic deformation of the material is done in…

Q: What are the two most common systems of units?

A: Given Data⇒ systems of units Problem statement⇒ Problem says What are the two most common systems of…

Q: 49. Which of the objects seen above would be the best choice to be completely machined on a lathe?…

A: Given:Find:49) The objects seen above would be the best choice to be completely machined on a…

Q: 18. How far off from the center of the support is the center of the two holes in the bosses of the…

A: 18)    Distance=4.2-0.66                   =3.54 in

Q: What is speed?

A: Speed is a scalar quantity that can give us information about the rate of an object or a body…

Q: what if you have multiple liquids acting on the triangle?

A:

Q: can you make a sketch of the solution

A:

Q: 1.Forging is a process that uses application of force to give shape to metal.

A: Forging is a process that uses application of force to give shape to metal. Answer: True

Q: 7 Doorbe Daanbe the proccdoe lor cvalvahon crnd Cncl improement f laaul. ?

A: Systematic Layout Planning Procedure:- It is a procedure layout design approach developed by Muther…

Q: What about density?

A:

Q: What is the maximum thickness dimension allowed on the part?

A:

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: What does shear strains cause?

A: Answer Shear Strain : it is the angular displacement from the original position

Q: Why is it called Mohr's circle?

A: Mohr’s  circle is graphical representation which enables us to visualize the relationships between…

Q: What is the frictional Force

A:

Q: (a) Figure Q2(a) shown the nut slides down the cord OA. When it is at the midpoint, its speed is 200…

A: Givenspeed=200mm/sAcceleration=10mm/s2

Q: In a hydraulic press machine the diameters of the effort and load pistons are respectively 25 cm and…

A:

Q: What is external force?

A: Answer : Force - It is an effect which changes or try to change the state of a body.

Q: How can I calculate the force tho

A: The stress is defined as the resisting force per unit area. here, σAl=12800 psiσsteel=18850…

Q: How would density be used to determine the concentration of antifreeze in the cooling system of an…

A: The density of antifreeze in the cooling system of automobiles is used to determine the…

Q: What are limits or limits of size?

A: This question belongs to Metrology. Metrology is a science of measurement by using different…

Q: When does a couple of moment work?

A: A couple is when a system of forces has no net force but has a net moment. A couple causes pure…

Q: b) Determine the March number of the bullet for both medium.

A: (b) Consider the helium gas and calculate the speed of sound in helium. cHe=γRTMFor γ,…

Q: The possibility to make the required shape from the material is considered during the criteria for…

A: Material to make the desired shape is considered during the criteria of selection. Because during…

Q: What are the different systems of Units?

A: The different system of units are listed below: SI system MKS system FPS system CGS system The SI…

Q: Is this definitely correct? A few calculators online such as BMEP calculators give me a different…

A: Given data:Torque = T = 100 NmEngine is four stroke,so there is one power stroke after two…

Q: Q1- Compare between the ferrous and non-ferrous metals in terms of the strength, hardness, weight,…

A: Ferrous metals contain iron, and non-ferrous metals don't. That means each type of ferrous and…

Q: For each of the mating part pairs below, and lower limit for each part. For A and B, səddn express…

A:

Q: 583 mK/s = ________ μK/ms 2. 583 mK/s = _______ K/s

A: Given data 1. 583 mK/s = ________ μK/ms 2. 583 mK/s = _______ K/s

Q: How does the tension in the string change as the masses start to move? Or does it?

A: Consider pulley mass system as shown in the figure below, Scenario 1 Assume the pulley does not…

Q: please, i need to see how did you get to this formula

A: ◆ The purpose of using this formula is to avoid complex calculation and to get the answer in minimum…

Q: Is this for number 1 only?

A:

Q: Define the term work of force?

A: Work of force is defined as the dot product of force and displacement  W=F.S…

Q: An engineer first draws a circle in a plane and uses a tool to convert the circle to a disk that is…

A: SolidWorks is a 3D parametric design software that is used to design all sorts of 2D and 3D parts…

Q: ith à neat sketch explain working of an engine in wh eous combustion öI äif-fuel mixture happens…

A: what is being talked about is a two stroke spark ignition engine

Q: In a lathe machine, The diameter of the driver and driven pulley are 2130 mm and 1590 mm…

A: The ratio of speed of driven pulley to speed of driver pulley is termed as speed ratio for a belt…