The rod shown below moves to the right on essentially zero-resistance rails at a speed of v = 4.12 m/s. If B = 1.35 T everywhere in the region, what is the current through the 5.0 resistor? Report your answer in units of milliamps.

The rod shown below moves to the right on essentially zero-resistance rails at a speed of v = 4.12 m/s. If B = 1.35 T everywhere in the region, what is the current through the 5.0 resistor? Report your answer in units of milliamps.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Related questions

Q: The thin copper wire with radius of 1.3 mm is wound into a torus shaped coil as revealed in figure.…

A: The given values are,

Q: 1. A large spool in an electrician's workshop has 75 m of insulation coated wire coiled around it.…

A: Given That-The initial length of coated wire Initial Current through the wire Final Current through…

Q: Questions in the attachments

A: (A) Given that the switch is open. R3 and the parallel connected R4 and R5 are in series, the…

Q: In the accompanying figure, the rails, connecting end pieces, and rod all have a resistance per unit…

Q: Problem 3. The reading on the ammeter in figure below is 3.00 A, and the current runs from right to…

A: a) Apply the KVL rule in the lower loop. ∑Vlower=024 V−I1(3 Ω)−(1 Ω)IA=024 V−I1(3 Ω)−(1 Ω)(3…

Q: Assume that R1 = 1.00 kohm, R2 = 2.00 kohm, R3 = 3.00 kohm, E1 = 60.0 V, E2 = 55.0 V and E3= 65.0 V.…

Q: The capacitor in the circuit shown below is initially uncharged. The switch is closed at t=0 s.…

A: The voltage of the battery is The capacitance of the capacitor is The resistance of the resistor is…

Q: The figure shows wire 1 in cross section; the wire is long and straight, carries a current of 4.06…

Q: Refer to diagram 1. In the circuit shown: R1 = 1.45 N, R2 = 7.04 Q, R3 = 6.3 N, L = 20 mH and V=…

A: Kirchhoff's loop rule states that in any closed path of an electrical circuit, the algebraic sum of…

Q: Given that a current of I(t)= 12t²+4 (where t is in s) is flowing parallel to the axis of a…

Q: In the accompanying figure, the rails, connecting end pieces, and rod all have a resistance per unit…

A: Here in this question, we will use the concept of motional emf. When a conductor moves in a Magnetic…

Q: A 0.1-A current flows through of a copper wire of length 1.0 m for 20 minutes. The diameter of the…

Q: Some airliners use wires of aluminum (resistivity2.75 * 10^-8 Ω . m) rather than copper to reduce…

A: We know that Ohm's Law is given as: R =VI ---(1) in the given question, length of aluminium wire,L =…

Q: Find the resistance between the inner and the outer curved surfaces of the block shown below, where…

A: Resistance is a measure of the difficulty of current flow. It is given by, R=VI We know voltage is…

Q: Taking R = 1.60 kN and E = 210 V in the figure below, R 2R be 28 4R 3R determine the direction and…

Q: A circuit is connected to a potential difference, V = 23.6 volts, at a power P = 9.3 watts. What is…

A: Calculate the current using the formula P = VI, where P is the power, V is the potential difference,…

Q: A cell of e.m.f. 2V and external resistance 0.5 is connected across a resistor (R). The current that…

A: To find-The value of external resistance=?Given-Emf (E1)=2 VInternal resistance (r1)=0.5 ohmEmf…

Q: The rod shown below moves to the right on essentially zero-resistance rails at a speed of v=2.20…

Q: A high-voltage transmission line with a diameter of 2.00 cm and a length of 200 km carries a steady…

A: Given that-Length of wire, L= 200 kmCurrent in the wire, I= 1000 ADiameter of the wire, d= 2.0…

Q: A cubic resistor R of side length L=2 m and resistivity p=1.5×10-6 Qm connected to a battery ɛ= 1.35…

A: Given a cubic resistor R of side length L=2 m and resistivity ρ=1.5×10-6 Ω.m connected to a battery…

Q: A square loop of nichrome wire (resistivity = 1.50 x 106 2.m) measures 1 cm per side. The wire has a…

A: Solution: To find the voltage of the ideal battery, we need to first determine the magnetic field…

Q: The switch in the circuit below has been open for a very long time. If L is 8.04 Henries, the…

A: The current I2 at the moment switch is closed is 0.63 Amperes.

Q: CB Vcase=? www /=? 5 mA (a) What is the voltage (in V) on the case if 5.00 mA flows through the…

Q: Suppose we are told that 1000 sodium ions (each carrying charge +e) flow across a cell membrane in…

Q: Consider the circuit shown in the figure, where ɛ, = 22.7 V, E, = 12.3 V, and R = 14.0 Q. (Due to…

Q: A large spool in an electrician’s workshop has 75 m of insulation coated wire coiled around it. When…

A: Given Data: The initial length of coated wire L1=75 m Initial Current through the wire I1=2.4 A…

Q: Problem 3: Copper has a resistivity of pc = 1.72 × 10-8 2 m. An extension cord made of copper is…

A: Question is based upon Ohm's law and resistivity.

Q: 24. A conductor carries a current that is decreasing exponentially with time. The current is modeled…

A: 24 Given, I=I0 e-t/τ I0=3.0 A τ=0.50s Let 𝓠 be the amount of charge that flows…

Q: Chapter 27, Problem 063 In the circuit of the figure 8 = 4.20 kV, C = 7.90 µF, R₁ = R₂ = R3 = 1.01…

Q: current I (in A) passing in the wire

Q: Taking R = 1.80 kN and &E = 340 V in the figure shown below, determine the magnitude and direction…

Q: in bare feet is standing under a tree during a thunderstorm, seeking shelter from the rain. A…

Q: of 202/cm. The rod moves to the left at v= 4 m/s. If B = 0.75 the current in the circuit (a) when a…

Q: Given that a current of I(t)= 7t2+4 (where t is in s) is flowing parallel to the axis of a…

A: The current density is the ratio of current and area. The current is given as

Q: The total amount of charge that has entered a wire at time t is given by the expression Q-(20…

Q: The 17.0 cm long rod in the figure below moves at 4.00 m/s. Application of Lenz's X law B. RO RHR-2…

A: Given that: The length of the rod is l=17 cm. The velocity is v=4 m/s. The induced emf is e=8.70 V…

Q: ch S is closed at t = 0. (a) When the voltage across the capacitor is 8.00 V, what is the magnitude…

A: In the figure, We have given ε= 36.0 V C = 5.0 μF = 5.0 x 10-6 F R = 120 ohms Find:- (a) When…

Q: Along the x axis, 3.57E16 electrons move from x = –1.00 m to x = 1.00 m in 9.25 s. What is the…

A: To find the average current through the origin, we need to calculate the total charge passing…

Q: In the figure current is set up through a truncated right circular cone of resistivity 731 02-m,…

A: The current i enters the truncated cone at left end and leaves at the right end. Let this represent…

Q: A copper wire coil has a resistance of R = 10.8 Ω. The wire mass is m = 6.82 kg. How many metres of…

A: The Density of Copper is D = 8940 kg /m3And the resistivity of Copper is ρ = 1.68×10-8 Ω .m and we…

Q: A man foolishly tries to fish a burning piece of bread from a toaster with a metal butter knife and…

A: Given Data: The voltage is, V=120 V The threshold of sensation current is, I=1 mA The expression…

Q: The quantity of charge (in C) that has passed through a certain surface area varies with time…

A: Given: The quantity of charge is given as,

Q: In the figure & = 5.78 V, Ɛ2 = 10.4 V, R1 = 95.6 N, R2 = 200 Q, and R3 = 312 0. One point of the…

A: According to Kirchhoff first law Algebraic sum of current at a junction is always zero According to…

Q: In the accompanying figure, the rails, connecting end pieces, and rod all have a resistance per unit…

Q: nd the currents (In A) flowing in the circuit in the figure. (Indicate the direction with the sign…

Q: Given that a current of I(t)= 2t2+4 (where t is in s) is flowing parallel to the axis of a…

A: Given,

Q: current flowing through resistance

Question

The rod shown below moves to the right on essentially zero-resistance rails at a speed of
v = 4.12 m/s. If B = 1.35 T everywhere in the region, what is the current through the
5.0 - resistor? Report your answer in units of milliamps.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Determine the given data:

VIEW

Step 2: To find, current in milliamps

VIEW

Step 3: Calculate as per above formula,

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

A copper conductor has a diameter of 12 inch and it is 104 feet long. Assume that it carriers a total DC current of 16A and rho=1.72x10-8 capital omegam. What current density (in A/m2) exists in it? give the complete solution and express the final answer in 3 decimal places
Given that a current of I(t)= 5t2+4 (where t is in s) is flowing parallel to the axis of a cylindrical conductor. If the cylinder has a radius of 0.2 mm and a length of 50 cm. Find the current density in units of MA/m2 at t=5.9 s. Note the unit MA/m²=10°A/m² Select one: O A. 267 O B. 1417 Oc. 2595 O D. 3108 O E. 4250
A toaster oven is rated at 1900 WW for operation at 120 VV, 60 HzHz. Part A What is the resistance of the oven heater element? Express your answer with the appropriate units. Part B What is the peak current through it? Express your answer with the appropriate units. Part C What is the peak power dissipated by the oven? Express your answer with the appropriate units.
A,B
A resistor composed of carbon =(p=3.5*10^5 Ω*m) having a radius of 1.2mm and a length of 3.1mm is connected to a 6V batter. How much energy is dissipated by the resistor in 5 minutes?
In the accompanying figure, the rails, connecting end pieces, and rod all have a resistance per unit length of 40/cm. The rod moves to the left at v = 3 m/s. If B = 0.65 T everywhere in the region, what is the current in the circuit (a) when a = 8 cm? (b) when a = 4.5 cm? Description of Image B Hint a. When a = 8 cm, a counterclockwise mA flows in the circuit. b. When a = = 4.5 cm, 5.48 o current of 9.75 4.0 cm X = 5.48 mA flows in the circuit. X = 9.75
In the circuit below, it is known that R1 = 10 kΩ, R2 = 15 kΩ, and C = 0.4 μF, and a battery with an Emf of 20 Volts. Initially, the connector (switch) is connected for a long time until it reaches a steady state. Then the switch is disconnected/opened at t = 0. What is the current flowing in resistor 2 at t = 4 ms?
A HF 2.0 F 10 At an instant when Q = B 81 nC and VA - VB = -26 mV, determine the current in the circuit segment shown above. A negative sign in your answer represents current from left to right, while a positive current is right to left.
In this experiment, you have a 28.4N resistor. If the lab manual specifies that the maximum safe electric current through the resistor is 473MA, what is the maximum voltage (in unit of volt) you can apply to the resistor?
If the battery in the circuit below is 7.16V, resistor R1=331.15ΩΩ, and resistor R2=51.49ΩΩ, what is the magnitude of the current flowing through the circuit? Please give your answer in units of milli-Amps (mA).
In the figure R₁ = 9.42 kQ, R₂ = 15.7 kQ, C = 0.439 µF, and the ideal battery has emf & = 18.0 V. First, the switch is closed a long time so that the steady state is reached. Then the switch is opened at time t = 0. What is the current in resistor 2 at t = 4.10 ms? Number Units R₁ R₂ C
Problem 1. A 50.0 m long Aluminum wire has a diameter of 0.50 mm and is at 20.0°C. If it carries a current of 0.50 mA, (a) calculate the power delivered to it? (b) If the temperature is increased to 340°C and the potential difference across the wire remains constant, what is the power delivered?