The ring shown is subjected to two forces F1 and F2. If it is required that the resultant force have a magnitude of 1 kN and be directed vertically downward. Determine (a) the magnitude of F1 and F2 provided that = 30° (b) the magnitude of F1 and F2 if F2 is to be a minimum. 20

The ring shown is subjected to two forces F1 and F2. If it is required that the resultant force have a magnitude of 1 kN and be directed vertically downward. Determine (a) the magnitude of F1 and F2 provided that = 30° (b) the magnitude of F1 and F2 if F2 is to be a minimum. 20

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.48P: The pole OB is subjected to the 6004b force at B. Determine (a) the rectangular components of the...

See similar textbooks

Related questions

Q: What action does an impulsecause? What path does a projectiletake? Whathappens to the acceleration…

Q: A force acting through the point (x, y, z) where X = 4, y = -3 and Z = 8 is given by the vector: F =…

A: moment M = r X F Answer: 66.468 N-m

Q: angular motion shown. At this instant, Determine: 1- The velocities of gear center 0 and collar B.…

Q: Q2:B) Calculate the power required to pull (1.5m × 1.5m) flat plate at speed (1 m/s) to the left…

Q: Question 2: a) What is entrance region and fully developed region? Discuss it with figures. b) What…

Q: 1. A 16-cm square steel bearing plate lies between a 12-cm diameter wooden post and a concrete…

Q: Q3:A) List the devises that used to measure the velocity, pressure, volume flow rate and sketch each…

A: To find :- Device used to measure , velocity, pressure and flow rate

Q: The net head influence to a Caplan turbine is 45m. the working fluid hits the rotor and the rotor…

Q: 3 m B 2 m LA D 3 @ 4m 12 24 KN E F

A: given; lets take vertical reaction force at A =RVAlets take horizontal reaction force at A =RHAlets…

Q: (3) A circular cam 8-in in diameter rotates off-center with an eccentrity e = 1” & operates the…

Q: - For the fig. (la) choose the correct sectional view explaining the reasons for the errors to…

A: we have to select the appropriate representation for the cross section

Q: Can you please show me how to calculate the stress and strain on this figure. use this formula or…

A: For stress, σ=FA F - applied load (known to you) A- effective cross section…

Q: Determine the moment of inertia about the x-axis of each of the areas shown

Q: The concrete post is reinforced using six steel reiforcing rods, each having a diameter of 20 mm.…

A: Given data: Diameter of each rod = d = 20 mm Applied axial load = P = 900 kN Modulus of elasticity…

Q: 03 - Determine the reactions at A and B. in the Figure 7. Fig. (7) 9 kN 5 kN/m 2m 20 KN 1.5m 4 kN/m

A: For solution refer below images.

Q: Find the allowable maximum value of F.

A: we have to evaluate the maximum bending stress

Q: Determine the x- and y-coordinates of the centroid of the shaded area. y -y=yo-kx³ 3 300 mm 4 150 mm

Q: Position analysis of Scotch Yoke Mechanism Understand the Scotch Yoke Mechanism and observe and…

Q: The thin-walled cylinder can be supported in one of two ways as shown. Determine the state of stress…

A: Calculated the state of stress in the wall of the cylinder for both cases.

Q: Draw Mohr's circle that describes each of the following states of stress. 5 MPa 20 ksi 5 MPa - 20…

A: To draw the Mohr's circle for the given state of stresses

Q: Q2/ The 300N force is resultant of two forces, one of the force (T) has the direction along tine AB…

Q: Q2-A- Use the graphical method to find the magnitude and direction of the resultant of these forces…

Q: 8) A 5.9866 cm-diameter water jet with V-45 m/s, strikes a moving blade with V-15 m/s. The power…

Q: (12) A truck spring has ten leaves of graduated length. The spring supports are 42½-in apart & the…

Q: For 13 to 15. The compound bar carries the axial forces P and 2P. The working stresses are 40 ksi…

A: For solution refer below images.

Q: Q2:B) Calculate the power required to pull (1.5m x 1.5m) flat plate at speed (1 m/s) to the left…

Q: A dead weight tester is a device commonly used for calibrating pressure gauges. Weight loaded into…

Q: 04) Define the boundary layer, then find the thickness of boundary layer, shear stress, drag force…

Q: Q2 -A- Use the graphical method to find the magnitude and direction of the resultant of these…

Q: 1 5) Consider the flow in pipe in figure. If P₁ -AP/y. b) The flow direction is from 2 to 1 if AZ…

Q: a projectile is fired with an initial velocity of 120 m/s off the roof of the building. Determine…

Q: (b) increase in viscosity of liquid (c)decrease in viscosity of gas (e) (a) and (d) above. O The…

A: As per guidelines we need to answer only first question so please repost rest questions separately.

Q: should not exceed to a cylindrical space of 1¾-in in diameter. The spring index is 6.0 & the maximum…

Q: A 250 kg part falls from an airplane and hits the ground at 150kmin a) find the kinetic energy

A: Given data : Mass m=250 kg Velocity V=150 km/h

Q: Two identical masses are attached to frictionless pulleys by very light strings wrapped around the…

A: The hollow shaft has more moment of inertia than solid shaft for same mass and radius. The hollow…

Q: Q. 1 Determine the coordinate angle for F2 and then express each force acting on the bracket as…

Q: The steel water pipe has an inner diameter of 12 in. and wall thickness 0.25 in. If the valve A is…

A: Introduction: The tension is created by fighting the bursting effect of the imposed internal…

Q: Q2:B) Calculate the power required to pull (1.5m x 1.5m) flat plate at speed (1 m/s) to the left…

A: Given data Dimensions of plate = 1.5 m x 1.5 m Speed of flat plate = 1 m/s Horizontal spacing = t =…

Q: In a metal forming operation when the material has just started yielding, the principal stresses 0₁…

Q: The pressure tank shown is fabricated from spirally wrapped metal plates that are welded at the…

A: The largest gage pressure that can be used inside the tank if the allowable normal stress…

Q: 1- The use of lubricant in wire drawing die.

A: we have to discuss the use of lubricant in wire drawing

Q: How far is will an object in a standard gravitational field drop in 13 sec, starting from rest and…

Q: complement of the binary number 10110? (a) 01010 (b) 01001 (c) 10001. 4. The binary coded decimal…

A: Two's complement is find out by first flipping the number then adding 1 to that.

Q: A furnace wall lining is made up of material with k = 2.5 w/mk. the temperature of the inner and…

A: One-dimensional heat transfer through a simple or composite body exposed to convection from both…

Q: A nozzle is a device that converts fluid thermal energy, enthalpy into kinetic energy. The kinetic…

A: Consider an open system which is receiving some energy from outside along with some heat interaction…

Q: The temperature distribution and boundary condition in part of a solid is shown below; Determine the…

A: Given : To find : Temperature distribution

Q: Q/ 1000 kg car requires eight seconds to change its speed from 0 km/h to 140 km/h. What is the…

Q: The asymmetric simple truss is loaded as shown. Determine the reactions at A and D. Neglect the…

Q: QUESTION 2. A smooth rod with a length of 21 is bent as in Figure 2 and small oscillations are made…

Q: Q1 -A- A man stands on the middle rung of a 250 N ladder resting on a smooth floor and against a…

Question

The ring shown is subjected to two forces F1 and F2. If it is required that
the resultant force have a magnitude of 1 kN and be directed vertically downward.
Determine
(a) the magnitude of F1 and F2 provided that = 30°
(b) the magnitude of F1 and F2 if F2 is to be a minimum.
20

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two rods and one cable are attached to the supports at O. If two of the forces are as shown, determine the magnitude F and direction of the third force so that the resultant of the three forces is vertically downward with a magnitude of 1060 lb. 840 lb Answers: F= 0= i 8 i 48 -CT 231 lb 0 400 lb
Two rods and one cable are attached to the supports at O. If two of the forces are as shown, determine the magnitude F and direction of the third force so that the resultant of the three forces is vertically downward with a magnitude of 1210 lb. F 990 lb 600 lb 8 Answers: F= i 0 = i 42° 30° lb 0
The 700-Ib force acting on the frame is to be resolved into the two components acting along the axis of the struts AB and AC. If the component of force along AC is required to be 300 Ib, directed from A to C, determine the magnitude of the force acting along AB and the angle e of the 700-Ib force.
Two rods and one cable are attached to the supports at O. If two of the forces are as shown, determine the magnitude F and direction 0 of the third force so that the resultant of the three forces is vertically downward with a magnitude of 1380 Ib. 830 lb 310 Ib 47° 22 Answers: F = i Ib i
y F3 F2 30 F1 Q3- Resolve each of the forces F1 = 10 kN, F2 = 18 kN and F3 = 12 kN, into components acting along the x and y directions and determine the following: (a) The magnitude of FR is . kN (b) The direction of FR measured from the x-axis is (degrees) ..........
The frame shown is subjected to a horizontal force F = {300j} N. Determine the magnitudes of the components of this force parallel and perpendicular to member AB.
Q2: Determine the magnitude of forces FA and FB acting on each chain in order to develop a resultant force of 600 N. directed along the positive Y- axis. FB FA 30
Q1. Two forces F₁ and F₂ act on the screw eye. If the resultant force FR has a magnitude of 80 lb and the coordinate direction angles shown, determine the magnitude of F₂ and its coordinate direction angles. F₂ FR = 80 lb 120°- -y X 130° F₁ = 50 lb
At what angle 0 must the 900-N force be applied in order that the resultant R of the two forces has a magnitude of 2000 N? For this condition, determine the angle B between R and the vertical. 1400 N 900 N
4. F =2 kN 30 FB If the resultant force of the two tugboats is 3kN, directed along the positive x-axis as shown, determine the following: Magnitude of Force Fg in kN. Value of the angle theta in degrees.
The truck shown below is to be towed using two ropes. If the resultant force is to be 950 N, directed along the positive x axis, determine the magnitudes of forces Fa and Fp acting in each rope and the angle 6 of Fp so that the magnitude of Fp is a minimum. Fa acts at 20° from the x axis as shown.
Three forces are applied to a bracket as shown. If the resultant R of these three forces is directed along the positive u axis, for e = 15° determine the magnitudes of the force F, and the resultant R. F = 52 lb 12 F, = 80 lb 25°