The rigid bar AB is supported by two rods made of the same material. If the bar is horizontal before the load P is applied, find the distance x that locates the position where P must act if the bar is to remain horizontal. Neglect the weight of bar AB. L = 3 ft A = 0.2 in.2 L = 2 ft P A = 0.4 in.2 A В 10 ft

The rigid bar AB is supported by two rods made of the same material. If the bar is horizontal before the load P is applied, find the distance x that locates the position where P must act if the bar is to remain horizontal. Neglect the weight of bar AB. L = 3 ft A = 0.2 in.2 L = 2 ft P A = 0.4 in.2 A В 10 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The bar AB is supported by two rods- steel on the left and bronze on the right. If the bar is horizontal before load P is applied, find the distance x (in meters) that locates the position where P must act if the bar is to remain horizontal. (E of steel 29000 ksi and E of bronze = 83 GPa) Neglect the weight of bar AB. L=2ft Aw02 in? A 0.4 in 1on
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1690 in.*). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 170 kip-ft, P = 30 kips, LAB = 6.1 ft, Lec = 9.2 ft. P MA В C LAB LBC Answer: (a) VA = in. (b) Vg = in.
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1500 in.“]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 150 kip-ft, P = 26 kips, LAB = 6.1 ft, LBC = 9.2 ft. MA A LAB LBC
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1570 in.“]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 160 kip-ft, P = 10 kips, LAB = 9.0 ft, LBC = 13.5 ft. MA A В C LAB LBC Answer: (a) VA = in. (b) Ув in.
The force in member AB of truss joint B shown in figure is given as 15 N B• - 10 N AB a. 10 N compression b. 10 N tension c. 15 N compression O d. 15 N tension
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; | = 1960 in.4]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 160 kip-ft, P = 17 kips, LAB = 6.4 ft, LBC = 9.6 ft. AP MA A B C LAB LBC Answer: (a) VA = in. (b) VB = in.
The simply supported beam consists of a W21x44 structural steel wide-flange shape [E = 29,000 ksi; I= 843 in."1. Assume that the support at D can provide resistance either up or down. Fora loading of w= 7.2 kips/ft, determine: (a) the beam deflection VA at point A. (b) the beam deflection vc at point C. Assume LAB= 10 ft, LBc = 5 ft, LCD =5 ft, LDE=5 ft. B LAB LBC LCD LDE Answers: (a) VA = in. (b) vc = in.
Problem 1 The truss, given below, is subjected to the forces shown. 1) By applying equilibrium equations for the whole truss, find the reactions at the supports A and B. 2) Determine the force in each member of the truss, and state if the members are in tension or compression. Don't forget to draw FBD of each joint while solving. tan a = 10 5ft 5 D tan B 20 10 kips 10 kips 10 ft 10 ft
A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal before the load Pis applied. Bars (1) and (2) are both made from steel [E = 30100 ksi] and both have a cross-sectional area of 0.91 in.?. Assume L1=72 in., L2=133 in., a-68 in., b-100 in., and c-33 in. If the normal stress in each steel bar must be limited to 15.2 ksi, determine the maximum load P that may be applied to the rigid bar. (2) L2 |B D P Answer: P - i kips.
A inverted T-beam supports the three concentrated loads. Prove that the NA is 3.5 in. above the bottom and the INA = 97 in*. then use these values to determine the maximum value of P (lb) so that fyr s 4 ksi and fpe s 10 ksi. 1 in P 3P 8 in 4 ft 6 ft 6 ft 4 ft R2 1 in K4 in
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1640 in.*). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 240 kip-ft, P = 11 kips, LAB = 3.4 ft, Lgc = 5.1 ft. P MA A B C LAB LBC Answer: (a) VA = in. (b) Vg = in.
X Your answer is incorrect. The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E = 29,000 ksi; I = 843 in.“]. Assume that the support at D can provide resistance %3D either up or down. For a loading of w = 5.4 kips/ft, determine: (a) the beam deflection vg at point A. (b) the beam deflection vc at point C. Assume LAB = 13 ft, LBc = 7 ft, LcD =7 ft, LDE = 6 ft. %3D A B E LAB LBC LcD LCD Lpe Answers: (a) VA = -0.65669 in. (b) vc = 0.024937 in.