The reversing motor,which is controlled by two power relays,can be rotated in both directions as shown in the figure beiow.When the motor is mechanically combined with a lead screw,the rotary motion is converted to a linear one,such as the one moving lef tor right on the worktable in the layout.The desired direction of rotation is selected via the two STAFIT buttons,respectively.The limit switches LS1 and LS2,located at the two extreme motion limits,ensure 1-rqtf we forget to stop the movement of the worktable,then it will stop automatically, and the mechanism of the layout will not be destroyed.Draw the circuit of automation.

The reversing motor,which is controlled by two power relays,can be rotated in both directions as shown in the figure beiow.When the motor is mechanically combined with a lead screw,the rotary motion is converted to a linear one,such as the one moving lef tor right on the worktable in the layout.The desired direction of rotation is selected via the two STAFIT buttons,respectively.The limit switches LS1 and LS2,located at the two extreme motion limits,ensure 1-rqtf we forget to stop the movement of the worktable,then it will stop automatically, and the mechanism of the layout will not be destroyed.Draw the circuit of automation.

Understanding Motor Controls

4th Edition

ISBN:9781337798686

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter8: Multiple Push Button Stations

Section: Chapter Questions

Problem 3RQ: The two STOP push buttons in Figure 8–2 are connected in series with each other. What would be the...

See similar textbooks

Similar questions

Write and draw the following grashof's criterion and kind of grashof's four-bar mechanism such as; 1. Crank-rocker mechanism; 2. Drag link mechanism; 3. Double rocker mechanism; 4. Crossover-position or charge-point mechanism; 5 Triple rocker mechanism (non-grashof). Use technical Pen for the following: 0.2(light -for linkages and hand writing), 0.4(medium - for joints), 0.6(heavy - for fixed link or frames) use 2-4-4 template, all caps, italicized.
can you write the angles and loops for the first mechanism like they did in the second one
DOF for the following mechanism is .3 2
The number of degrees of freedom in the 3 link mechanism shown below is given by
1. In the drilling process shown in Figure 1, there are three cylinders in which cylinders A and B are used to clamp the work piece and Drill cylinder is used to lower and raise the drill. The sequence of operation is as follows: activate the direction control valve to start the process, Cylinder A and Cylinder B clamps the workpiece and then activate the second directional control valve to drill cylinder lowers the drill and raises afterwards. Once the drill is raised, cylinder A and cylinder B retracts. sensors Drill-high Drill Drill-Low Part / Material Cylinder A Cylinder B A+ B+ sensors Figure 1: Drilling Process а) Design the Hydraulic Circuit with proper labeling. Include the allocation list and the components required b) Draw the functional diagram/step diagram
ASAP
0340 030- 0100 Ø160 280 60 --030 -775 Kinematic Diagram of a Slider-Crank Mechanism (Figure 1-01) A. Draw the line diagram B. Compute the degree of freedom C. Label the parts -160- 020 065 $10 5 65 5
I need answer 2,3 and i give upvote (no plagarism)
Derive the inverse kinematics of the 3-DOF manipulator shown below: Joint 2 Joint 3 Joint 1
The roller track is to be swiveled by means of a double-acting cylinder. The signals to extend and to retract are given from separate push buttons. The cylinder is to remain in the position indicated by the last signal until an opposing signal is given. Draw the pneumatic circuit diagram using ISO symbols and connecting the ports with solid lines. (The positional sketch is the attached picture)
17- The memory unit of PLC is used to write the program to control output device. Select one: True False
What is the difference between a lever and a crank?. note: answer the question in 8-10 sentence only