The rectifier circuit shown below has the following parameters: V,= 170 sin 0; R=25 52; Turns Ratio N= 12:1 Treat the diode as IDEAL 20 15 10 5 of -5 -10 a) Draw the voltage across the resistor Your on the following graph. Label the peak value. -15 -20 Vs 0 12:1 0.5 7 b) What is the average voltage across the resistor? c) What is the average current through the resistor? +4 TC D1 R 1.57 0 270

The rectifier circuit shown below has the following parameters: V,= 170 sin 0; R=25 52; Turns Ratio N= 12:1 Treat the diode as IDEAL 20 15 10 5 of -5 -10 a) Draw the voltage across the resistor Your on the following graph. Label the peak value. -15 -20 Vs 0 12:1 0.5 7 b) What is the average voltage across the resistor? c) What is the average current through the resistor? +4 TC D1 R 1.57 0 270

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
What is CEMF?
One component that does not need to be installed in the correct orientation is a: a. Resistorb. Diodec. Voltage regulatord.
29. Does an increase in reverse bias for a Varactor diode cause an increase or decrease in capacitance? 30. If the load current through a SCR (Thyristor) reduces to almost zero, what will be the result?
H.W4 The diode in the single-phase half wave rectifier has a reverse recovery time of t 150μsec and the source voltage V₁ 200V at frequency = 5 kHz. Calculate the average output voltage. = =
In a single phase full wave controlled rectifier connected to Inductive load (with freewheeling diode) find the expression for the average value of voltage across the load when supply voltage is Vs = Vm sinwt and firing angle = a. Vm/TT cosa 2Vm/TT cosa Vm/TT (1+cosa) 2Vm/TT (1+cosa)
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
Single phase diode bridge rectifier is connected to 220 V, 50 Hz supply to feed 5-ohm resistor in series with 10 mH inductor. Calculate and draw the load current during the first two periods of supply voltages waveform.
The PIV experienced by each of the diodes for the below shown rectifier configuration is
Consider the following circuit diagram. Using practical diode model solve the following items. i. What is the type of rectification in this circuit? ii. Calculate the total peak secondary voltage (Note that “RMS" value is given in the circuit) iii. Sketch the plot of time vs voltage over Load (RL) iv. Find the average voltage over Load. v. Find the maximum current passing over diodes. vi. Find the peak inverse voltage (PIV) over the diodes. vii. Find the minimum fuse current rating for the primary coil. 5:1 D DA 120 V rms D3 D2 RL=10kQ RL out ell lelll
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
Design a single-phase full wave bridge rectifier with input voltage of 100v and inductive load of 10ohm and 40mH a. Show the waveform relation between the I/P and O/P b. Calculate the average O/P voltage c. Calculate the rms current