The rectangular metal block shown in Figure P1.10 is subjected to tensionwithin the elastic range. The increase in the length of a is 0.05 mm and thePoisson's ratio for the material is 0.33. If the original lengths of a and b were50 mm and 25 mm, respectively, what is the change in the length of b? Is thischange expansion or contraction?FIGURE P1.10

Poisson's ratio=-Lateral strain/Linear stress μ=-∆b/b∆a/ahere,μ=0.33a=50 mm∆a=0.05 mmb=25 mm

Answered: The rectangular metal block shown in…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel bar is held by two fixed supports as shown in the figure and is subjected to an increased temperature of AT = 200°C. If coefficient of thermal expansion and young's modulus of elasticity of steel are 11 x 10-6/°C and 200 GPa respectively, the magnitude of thermal stress (in MPa) induced in the bar is
A steel bar 100 mm long is subjected to a tensile stress o. If change in length of bar is 0.05 mm what is the value of o? Given E = 200 GPa
Last digit of my id is 0
A composite column is formed by placing a steel bar 20 mm diameter and 200 mm long, inside an alloy cylinder of the same length whose internal and external diameters are 20 mm and 25 mm respectively. The column is then subjected to an axial load of 50 kN. Modulus of elasticity for steel and alloy is 200000MPa and 70000MPa respectively. Which of the following gives the stress in the steel bar? a. 132.98 MPa b. 46.54 MPa c. 74.80 MPa d. 166.23 MPa
A round steel alloy bar with a diameter of 19mm and a gauge length of 76mm was subjected to tension, with the results shown in Table. Using a computer spreadsheet program, plot the stress–strain relationship. From the graph, determine the Young’s modulus of the steel alloy and the deformation corresponding to a 37kN load.
Topic: temperature change
The lower ends of the three bars in the figure are rigid homogeneous W = at the same level before the 100 kN block is attached. The temperature of the bars is then increased by 80°c. The block is assumed to remain horizontal after all deformations have occurred. The properties of the bars are shown in the table. STEEL BRÖNZE Length, L Area, A Modulus of Elasticity, E Coefficient of Thermal Expansion, a 1.0 m 1.6 m 500 mm2 900 mm? 200 GPa 83 GPa 11.7x10-6 mm/ (mm-°c) 18x10-6 mm/ (mm-°C) Calculate the stress developed in the bronze bar. Bronze Steel Steel A Calculate the stress developed in the steel bar. FIGURE 10
Data taken from a stress-strain test for a brittle alloy are given in the table. The curve is linear between the origin and the first point. o (ksi) e (in./in.) 0 0 44.8 0.0008 54.0 0.0013 57.5 0.0017 59.5 0.0021 60.0 0.0023 Part A Determine approximately the modulus of toughness. The rupture stress is o, 30.0 ksi. Express your answer in inch-pounds per cubic inch as an integer. VAE Ivec U Submit Provide Feedback Request Answer in-lb/in³
A brass alloy rod having a cross sectional area of 0.24 in.2and a modulus of 16 * 106 psi is subjected to a tensile load. Plastic deformation was observed to begin at a load of 8,944 lb.a. Determine the maximum stress that can be applied without plastic deformation.b. If the maximum length to which a specimen may be stretched without causing plastic deformation is 3.28 in., what is the original specimen length?
A 4-m-long steel plate with a rectangular cross section (10 mm * 50 mm) is resting on a frictionless surface under the sun. The plate temperature is meas-ured to be at 40°C. The plate is then moved into a cold room and is left to rest on a frictionless surface. After several hours, the plate temperature is meas-ured to be at 5°C. The steel has a modulus of elasticity equal to 200 GPa and a coefficient of thermal expansion equal to 1.1 * 10-5m/m/°C. a. What is the length of shrinkage?b. What tension load is needed to return the length to the original value of 4meters?c. What is the longitudinal strain under this load?
I need the answer as soon as possible

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS