The reaction of the ground is uniformly distributed. Draw the shear and bending moment diagram for the beam AB and calculate the magnitude of the maximum shear and moment of the beam. (Hint: first find w)

The reaction of the ground is uniformly distributed. Draw the shear and bending moment diagram for the beam AB and calculate the magnitude of the maximum shear and moment of the beam. (Hint: first find w)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SOLVE USING THREE MOMENT EQUATION
What is the reaction at B in kN? Replace the distributed loading by an equivalent resultant force and specify its location the beam measured from the pin at A. Solve also for the support reactions. 4 kN/m 2 kN/m B. 3 m 3 m O 8.5 O 6.5 O 7.5 O 4.5 O 3.5 O 7
Determine the moment over the support at B of the beam shown in the figure and the Reaction Forces at support A, B and D.
The frame is subjected to a distributed load which starts at 200 N/m at A and increases to 250N/m at D. a) Using the figure to the right of the frame, draw a free-body diagram of the frame. Label the reaction forces at A and D and replace the distributed load with equivalent force(s). b) Draw a free-body diagram of member AB and member BC and label all the forces. c) Determine the reaction forces at A and C. (Be sure to include the direction.) For full credit indicate for each equilibrium equation whether the equation is for the entire frame, member AB, or member BC. 250 N/m 200 N/m A - 3 m 3 m 2.5 m 6 m 6 m Free-body Diagram of Frame
A shear directed downward at the left end of a conjugate beam is considered as: a. Negative slope b. Positive slope
1. 1 For the beam shown below, (a) Draw the V-Diagram (b) Draw the M-Diagram (c) Find the largest value of o, and give the (x,y,z) coordinates of its location. (d) Find the largest value of 7y and give the (x,y,z) coordinates of its location. List of beam properties List of displacements List of forces of single-point constraints (these are the reactions at the supports) List of forces in beam elements List of stresses in beam elements S = 0.05" Si = 0.04" 30" Cross section Aluminum 50.000 in.lb E- l0xIo psi V=0. 3 60"
A beam is loaded and supported as shown. Use the fourth-order integration method to determine the reactions at supports A and B. Assume w, 13 kN/mand L= 11 m. Reaction forces are positive upwards and couples are positive counter-clockwise unless otherwise stated. - wx) =w, sin (x x/L) Wo B.
2.) Determine the reaction at the center support of the continuous beam using double integration method with singularity functions. Assume the modulus of elasticity E and moment of inertia I is constant throughout the entire beam. After solving for the reaction force R2, solve for the remaining reactions R¡ and R3 using equations of statics. Plot the shear and moment diagram and determine the distance from the leftmost support where the maximum bending moment occurs. What is this maximum bending moment. Express your answers in terms of the variables w and L. R.
1. The beam is subjected to a load F = 400 N and is supported by the rope and the smooth surfaces at A and B. a. Draw the free-body diagram of the beam. b. What are the magnitudes of the reactions at A and B? 45% 1.2 m- -1.5 m- F 11 B 30⁰
-; For the frame shown below, determine the degree of indeterminacy and compute the reactions at D. El=constant. 33 KN/m B 5 m 6 m D 2 m О KN 2 m A
1. Given: A structure shown below Find: (1) Determine the magnitudes and locations of the two distributed loadings. In other words, determine the magnitude and location of the loading between A and C, and those of the loading between D and B. (2) For the member DEB, (a) take the moment at B and find the reaction at E and (b) then find By by either Fy= 0, or EMp = 0. (Recall that support conditions at B and E are rollers, so there are no reactions in x-direction.) (3) For the whole structure, 3 unknown forces and moment at A (Ax, Ay and Ma) are the only unknowns. Determine those 3 unknowns at A. 900 N/m 900 N/m B A C D 2E - 3 m 3 m - 4 m - 3 m3 m-
Draw the bending-moment diagram and compute the reactions. E and I are constant. Consider only bending deformation.