The puncher is to drive a 30 mm diameter hole to a steel plate. If the allowable axial stress of the cher is limited to 100 MPa, determine the thickness (t) of the steel plate. The maximum shear stress he steel plate is 50 MPa. F D

Q: An object has specific weight of 2.33kN/m^3. Compute the following: mass density, mass if volume is…

A: Given data in question  Specific weight  Volume  To find out  Mass density  Specific volume

Q: 3. Three objects are hanging from a 10m long beam as the locations shown. The beam is hung from the…

A:

Q: Problem 2 Determine the magnitude and direction of the resultant force for the following forces…

A: A set of forces are given and their angles are also given.

Q: As showni in the above diagram, rope and pulley system is used to support a load w with a mass of…

A:

Q: The figure shows a metal hanging by a thin wire from a floating wood block. The wood block has a…

A:

Q: Find X, Y Components of forces system * shown in the figure F= 250 N F= 200 N 45° 3 F=400 N

A: Component of force in X direction:RX=-400+250×sin45-200×45=-383.22 N

Q: Locate the centroid for the following shape shown (Note: reference point is given in the figure). 6…

A: Given data in question  Dimensions  = 6in, 3in, 6in and 6 in To find out  Centroid of the composite…

Q: Using the data on the for problem 2: Please answer the following question in the picture make sure…

A:

Q: For the given section shown in the figure, determine the following: 20 mm Moment of inertia with…

A: For the given angle section, the position of centroid is given by:…

Q: Find the centroid of the given figure y 3 in. 1 in. 1 in. a 2 in. -3 in.-3 in.

A: From the given figure, We have to find the centroid

Q: Problem 1 Determine the magnitude of the moment about point A and its direction at the plane having…

A:

Q: Two objects of mass m1 = 10 kg and m2 = 5 kg are connected by a light, inextensible cord and hung…

A:

Q: What pressure is required to reduce the volume of water by 0.60 percent If the volume modulus of…

A:

Q: Instruction: Solve the following problems presented below. Write your solutions on a clean white…

A: By using equations of equilibrium we can solve the P and F.

Q: Situation 4: From the given set of forces shown in the figure, determine the: 28 N 34 N 10- 26 N 1 m…

A:

Q: 8. What is the relation between kinetic energy and momentum? a) p=m/v b) p=mva c) p=mv d) p=m

A:

Q: 3. A steel rod having a cross-sectional area of 450 mm² and a length of 185 m is suspended…

A: Self weight = 7850kg/m3= 3465.3825 N L = 185m A = 200mm2 E = 200GPa   It has been asked in the…

Q: A solid metal bar of uniform sectional area throughout its length hangs vertically from its upper…

A: Uniform  sectional area To find the total elongation of the bar

Q: For the figure shown below with 3 bar elements connecting two rigid walls, what is the stiffness…

A:

Q: Determine the values of the principal moments of inertia in x106 mm'4 50 400 A2 50 500

A: We have to determine value of the principal moment of inertia in ×106 mm4 according to the given…

Q: PROBLEM A rigid body subjected to 5 forces and a couple (moment) is shown in Find (a) the single…

A:

Q: 2) Given the figure below, answer the following questions. +Y +X B +Z Notot 200 kL: 20°: 450 P.

A:

Q: 1. If the weight of the body is 9.892 N when the acceleration of gravity is 9.70 m/s^2, what is the…

A: CONCEPT: Weight = mass*g Mass remains constant

Q: 3) Nails are used to connect three boards to form a beam as shown in the figure. Each nail has a…

A: Basically, a shear force is a force that acts parallel to a body's surface or cross-section, such as…

Q: 22:What are the forces acting on points A- E on the figure shown below? |2 kN/m 2 kN/m 1m 15m 16m 1m

A: Solution:- Given,

Q: Determine the resultant of the four forces acting on the body shown in Figure 300 N 400 N 60 54 500…

A:

Q: Suppose we have a uniform beam that is 3.73 metres long has a flexural rigidity of 34301Nm. Find the…

A:

Q: what is its specific weight? *

A:

Q: 11. Given the specific gravity of oil is 0.85, what is its density in Kg/m^3?

A: CONCEPT: Specific gravity (also known as relative density) is the ratio of density of a particular…

Q: de V = dE a= dv/dt ads= vdv

A:

Q: write down some quick thoughts on dynamic vs static changes.

A: In the field of civil engineering, dynamic and static changes refer to modifications made to…

Q: 150 N 30° 2.0 m 150 N 30⁰° A 50 N 100 N.m 2.0 m 0.67 m B 1.0 m 1.0 m ! 65° 200 N 80 N

A:

Q: For the shape below, assume the following dimensions: a = 175 mm b = 220 mm d = 300 mm t = 23 mm The…

A: Given:Required :Moment of inertia along centroidal y axis

Q: I am trying to build a wooden beam. The beam is a T-beam, reinforced with 2x4's. Given dimensions as…

A: Solution:

Q: A throat plate is a component that can be found in sewing machines. Shown in the figure is a…

A:

Q: Consider the U-beam section shown in the figure below. The beam section splits into 3 segments…

A: A1=120×30=3600cm2A2=40×180=7200cm2A3=30×120=3600cm2y1=d2=15cmy2=120cmy3=225cm

Q: 2 t 4 t/m 2 t.m 1 t/m ↑↑↑↑↑↑: 4

A:

Q: What do the x, y and z momentum equations simplify to if the Rossby number friction forces inertia…

A:

Q: Determine the deflection at point B given the cross-section of the beam and assuming E = 200 GPa. A…

A:

Q: The thin plate shown in the figure below is loaded with a 7000 lb concentrated force acting at node…

A:

Q: Given: Structure shown below (The thin plate has a mass per unit area of 10 kg/m².) Find: Mass…

A: When a body is rotated about any chosen axis, it requires a minimum torque to rotate the body, which…

Q: 23. If the specific weight of liquid is 8.0 KN/m^3, its density is 815.50 kg/m^3 8.16 kg/m^3 815.50…

A: GIVEN- Specific weight of liquid= 8.0kN/m3  DETERMINE- Density of the liquid?

Friction

Friction is defined as the force that prevents any solid surface, any layer of fluid, or any kind of element or material from sliding.