The properties of the reinforced concrete beam are b = 304 mm, d = 475 mm, Ast = 1035 mm2, and Est / Eco = 9. If the working stresses are 17.7 MPa for concrete and 114.5 MPa for steel, determine the corresponding bending moment (in Nm) for the steel. Round off the final answer to two decimal places. -b- h ΝΑ Ast (total area) d

The properties of the reinforced concrete beam are b = 304 mm, d = 475 mm, Ast = 1035 mm2, and Est / Eco = 9. If the working stresses are 17.7 MPa for concrete and 114.5 MPa for steel, determine the corresponding bending moment (in Nm) for the steel. Round off the final answer to two decimal places. -b- h ΝΑ Ast (total area) d

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The stress-strain diagram for polyester resin is shown in the figure. Both strut AB and column CD, madefrom this material, support the rigid beam AC. Calculate the angle of tilt of the beam when it is subjectedto load P = 60 kN. The diameter of the strut is 50 mm and the diameter of the column is 80 mm.Answer: θ = 0.327 degreesPlease indicate the location of the angle of tilt in the FBD.
Please solve only part 1 also draw free body diagram
A Normal-weight concrete T beam shown in the figure below is reinforced at the tension side by 3 - #25 bars. The concrete is assumingly uncracked and has a compressive strength of fe' = 29 MPa, fy=370 MPa, and the clear concrete cover is 40 mm, the modular ratio is n=9, and the web rein. is #10 mm. Determine the cracking moment (kN m) of the section using solution 2. 1300 125 250 500
.
The composite bar is subjected to a normal force P = 7500 lb as shown in the figure. The section of the composite bar is composed of two hollow tubes and a solid steel core. Determine the axial stress developed in each bar. Use Ecu = 18 x 106 psi, Est = 30 x 106 psi, and Ebr = 16 x 106 psi.
10/10 FIND STRESS IN STEEL MATERIALS IN COMPOSITE COLUMIN SHOWN BELOW. IF E st= 200 kN/MM2, Ealu.=70 kN/MM2 100 kN RALU=30 MM Aluminum Steel 1m R ST 20 MM
Please try to solve only part 2 within 20 minute This is request
Solution w/FBD
A circular aluminum alloy [E = 70 GPa; a = 22.5 × 10-6/°C; v = 0.33] pipe has an outside diameter of 215 mm, a wall thickness of 12 mm, and a length of 4.3 m. The pipe supports a compressive load of 695 kN. After the temperature of the pipe drops 43°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) ō = i AD = i mm mm
Prob.5: A rectangular reinforced concrete beam has dimensions b = 300 mm, d = 530 mm and h = 600 mm, and is reinforced with 3 Ø32 mm bars. Materials strength are fe = 28 MPa, fy= 414 MPa. a) Find the moment that will produce the first cracking at the bottom surface of the beam basing your calculations on Ig. b) Determine the maximum stress in the steel and in the concrete under this Design of Reinforced Concrete Structures moment.
Reinforced concrete
The solid circular drill rod AB is made of a steel that is assumed to be elastoplastic with τY = 22 ksi and G = 11.2 × 106 psi. Knowing that a torque T = 72 kip·in. is applied to the rod and then removed, determine the maximum residual shearing stress in the rod. The maximum residual shearing stress in the rod is ksi.