The pressure drop across the tube bank is?
Q: erties of the sphere material are E Ex 10 m2 /s. o sphere remain in the water bath
A: We will utilize the idea of lumped heat limit (conduction-convection frameworks). The lumped…
Q: A very long tube (>>1m) is closed at one end and is immersed in a big bath of mercury which entirely…
A: Given, that the tube is fully immersed in the Mercury bath. So in this scenario the tube is fully…
Q: Select a proper schedule of pipe for each of the following conditions: FOR SET B: Steam at at 900…
A: Given: Let us consider the given data, d=10 inP=900 psiaT=900°F To find: Proper schedule of pipe.
Q: Not yet answere Question 7 Marked out of 1 In ideal case and knowing that the area of the Venturi at…
A: Given :- In ideal case and knowing that the area of the Venturi at the inlet and outlet is the…
Q: 5- Compare the reading of pitot tube and the reading of anemometer to the measurement of air…
A: An anemometer is a device which is used to evaluate the velocity of the air by counting the number…
Q: The type of valve which is used to maintain the constant pressure and when the pressure increases it…
A: Given :- The type of valve which is used to maintain the constant pressure and when the pressure…
Q: reading shown? For the 6 psi. The fluid in both pines A and B is water
A: we will use the equation of inclined tube manometer PA+γ1h1γ2I2 sinθ-γ3h3 =PB
Q: (2) The tank below is cylindrical with a diameter of 10 m. The outlet is a cylindrical frictionless…
A:
Q: Calculate the volume flow rate of oil from the nozzle and the pressure at point B and D.
A:
Q: Reynolds number, based on the pipe diameter
A: Given; Two pipes of uniform section but different diameters carry water at the same flow rate.Water…
Q: There are three pipes and each has different friction or roughness factors below
A:
Q: Where does the value of the Rin the solution came from?
A:
Q: What is the pressure at 61, 500 ft in SI.
A:
Q: Q2) a horizontal air conditioning system as shown below consists of 90-degree elbows (K=0.3) and a…
A: the pressure at the inlet should be enough so that it can overcome the frictional head losses and…
Q: Bourdon tube is also referred to as an
A:
Q: convert 35 psig in kPaa
A: Psig and kPa both are units of pressure. Psig = pound per square inch kPa = kilo Pascal
Q: d) Pressure head at point 1 e) Pressure head at point 2
A:
Q: A condenser vacuum gauge reads 705 mmHG when the barometer stands at 746 mmHG. State the absolute…
A:
Q: 1) With the below nozzle arrangement, what pressure is needed in the pipe in order to get a nozzle…
A: From the given data,
Q: How to calculate the maximum stresses which are produced inside the boiler due to the pressure of…
A: How to calculate the maximum stresses which are produced inside the boiler due to the pressure of…
Q: For Ta pered pipe shown below, what is a as diameter of the pipe at
A:
Q: A pipe of cross-sectional area 2
A: ANSWER= 7.9m/s
Q: The vacuum pressure in condenser is 735 mm Hg .Barometer is 762 mm Hg .Find the absolute pressure in…
A:
Q: Question (1):- Find the pressure in the pipe shown in figure.if Pmer=13600kg/m' and pw=1000kg/m. 80…
A:
Q: The wall thickness of a pipe is referred to as the pipe's __________.
A: Thickness of the pipe is nothing but the difference between outer radius and inner radius.
Q: How much flow energy in kW required to move 3000liters/min. of water inside the pipe against a…
A: Given:Q=3000 L/minP1=100 KPaP2=300 KPa
Q: the pressure drop (in Pa) in the pipe is
A: Given, Water flows through,d= 10 mml= 250 mAverage velocity,v= 0.1 m/sDensity,ρ=997…
Q: The piping system shown in the figure is to move ethylene glycol at a flow rate of 50 gpm. Follow…
A: Requirement Pump Head =Friction Pressure drop + losses due to fittings and Valves +Gravity head…
Q: What will happen for the system, if the friction factor of the pipe increases to 0.1?
A: we can determine the head loss due to friction factor by the Darcy–Weisbach equation hf=f l v22gDf…
Q: determine the rate of flow through the boiler
A: Given data; L1=20×10-3 mk1=58 W/m0cL2=5×10-3mk2=0.116 W/m0cT1=3000CT2=500C Therefore find rate of…
Q: Delamine fereoune at depth g25m unside a liquid Jn swmmingpool
A: Given data : Density of water ρ=1000 kg/m3Acceleration due to gravity (g)=9.81 m/s2Depth (h)=25 m
Q: Sl unit for the pressure head at a point on the flowing liquid inside pipe is in m of liquid.
A: The height of liquid in a vertical column due to the pressure inside the container is called a…
Q: Head loss due to Friction.
A: Using Darcy–Weisbach equation
Q: Find max internal pressure
A:
Q: Estimate the leakage through the wall per
A: Given; A=4.6 m× 2.3 mX1=115 mm=0.115 mX2=75 mm=0.075 mX3=25mm=0.0025mT1=291 KT2=271…
Q: Discuss the difference between thin and thick walled pressure vessel
A: Difference between thin and thick walled pressure vessels Thin pressure vessel For thin pressure…
Q: Describe the uses of expansion in thermometers using diagrams
A: Describe the uses of expansion in thermometers using diagrams
Q: 3. Drive an equation to describe the effect of the tube's diameter on the liquid raise in cupillary…
A:
Q: The working fluid of the pressure gauge in Fig. 157 is mercury. Estimate the volumetric flow rate…
A: The Answer is below
Q: nm2 is inserted in a pipe of area 175E The pressure difference measured b nercury oil differential…
A: Given Data⇒ Area of orifice meter is A1=878 mm2A1=0.000878 m2 Area of pipe is A2=1756 mm2A2=0.001756…
Q: The air temperature at exit of the pipe is:
A: It is given that specific heat of air at constant pressure Cp=1.005 kJ/Kg-°C = 1005 J/Kg-°C Length…
Q: The pressure on a diver who is at a depth of 5 m below the surface of the water is
A: Given data : Depth=h Density of water=ρ Acceleration due to gravity=g To find : Pressure
Q: A horinzontal boiler 5 m long and 3 m diameter is half full of water. It is provided with 100 mm…
A: Given:- L=5m H=3m R=3/2=1.5m Radius of orifice = 0.1/2=0.05m Cd=0.60 To find:- Time taken to empty…
Q: Draw how it look if it is a turbulent flow in pipe.
A: To Draw : how turbulent flow look in pipe Turbulent flow : Turbulent flow is a fluid motion in…
Q: 1. What do you meant by friction and list out its types? 2.What do you meant by major loss in pipe?
A:
Q: hown below the laminar flow pass through moving plate. Tupper Tlower and Q e1
A: GIVEN:
Q: A square tube is welded on one side and will be filled with liquid of a relative density of
A: Liquid when enclosed within a container makes a pressure inside and then exerts force on the walls…
Q: What is the pipe pressure (pa)? Given the S for Mercury is 13 and S for fluid =3.4
A:
The pressure drop across the tube bank is?
Step by step
Solved in 2 steps with 3 images
- 7.43 Liquid sodium is to be heated from 500 K to 600 K by passing it at a flow rate of 5.0 kg/s through a 5-cmID tube whose surface is maintained at 620 K. What length of tube is required?5.7 The average Reynolds number for air passing in turbulent flow over a 2-m-long, flat plate is . Under these conditions, the average Nusselt number was found to be equal to 4150. Determine the average heat transfer coefficient for an oil having thermal properties similar to those in Appendix 2, Table 18, at at the same Reynolds number and flowing over the same plate.A steam reservoir is covered by a rectangular plate (its length is 1 m and width 2 m). The steam temperature is 95o C, and it is in contact with the plate. Over the outside surface of the plate, water is flowing at a speed of 3 m/sec at a temperature of 25o C. What is the mean Nusselt number over the plate? What is the mean heat transfer convective coefficient over the plate? What is the heat transfer rate to the water?
- Determine the convection heat transfer coefficient (in W/m?.K) for air flowing at a velocity of 3 m/s in a 10-cm diameter and 10-m long tube. Air enters the tube at 10°C and leaves at 20°C, i.e. air is heated. Take the property of air at 1 atm and assume flow to be fully developed. For air at 1 atm: Temperature k, W/m-K v, m?/s Pr 15°C 0.02476 1.470x10-5 0.7323 20°C 0.02514 1.516x10-5 0.7309 25°C 0.02551 1.562x105 0.7296 Hint: When the fluid temperature changes, we use its properties at mean temperature, unless otherwise specified. Round your answer to 2 decimal places.Water at 15ºC is to be heated to 65ºC by passing it over a bundle of 4-m-long 1-cm-diameter resistance heater rods maintained at 90ºC. Water approaches the heater rod bundle in normal direction at a mean velocity of 0.8 m/s. The rods arc arranged in-line with longitudinal and transverse pitches of SL 4 cm and ST 3 cm. Determine the number of tube rows NL in the flow direction needed to achieve the indicated temperature rise.7-115 Air is to be cooled in the evaporator section of a refrigerator by passing it over a bank of 0.8-cm-outer-diameter and 0.8-m-long tubes inside which the refrigerant is evaporating at –20°C. Air approaches the tube bank in the normal direction at 0°C and 1 atm with a mean velocity of 5 m/s. The tubes are arranged in-line with longitudinal and transverse pitches of SL = ST = 1.5 cm. There are 25 rows in the %D flow direction with 15 tubes in each row. Determine (a) the refrigeration capacity of this system and (b) pressure drop across the tube bank. Evaluate the air properties at an assumed mean temperature of -5°C and 1 atm. Is this a good assumption? 0.8 m Air 0°C 1 atm ST = 1.5 cm 5 m/s 0.8 cm 1.5 cm/ S, = Refrigerant, –20°C FIGURE P7–115
- Please help with this questionHot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. Thegas at 220°C flow is parallel over the upper and lower surfaces of a 3-m-longflat plate at a velocity of 3 m/s. If the flat plate surface temperature ismaintained at 80°C.Determine the local convection heat transfer coefficient at 1 m fromthe leading edge and calculate the average convection heat transfer coefficient over theentire plate.Air at 27 ⁰C and 1 atm flows over a flat plate at a velocity of 3m/s, assuming the plate is heated its entire length to a temperature of 70⁰C. Heat transferred in first 25 cm of the plate is?A 4m x 4m flat piale maintained at a constant temperature of NOC is subjected to parallel flow of nit at I am. 20 ', and 10 m's. The total drag force acting on the upper surface of the plate is measured to be 2.4N Determine the average convection hear transfer coefficient, and the rate of heat transfer between the upper surface of the plate and the air. The properties of air at 20 ° C and 1 atm from tables, are
- Air at 3*10-4 kg/s and 27°C enters a rectangular duct that is 1 m long and 4 mm x 16 mm on the sides. A uniform heat flux of 600 W/m2 is imposed on the duct surface. What is the mean temperature of the duct and the duct surface at the outlet?During air cooling of oranges, grapefruit, andtangelos, the heat transfer coefficient for combined convection,radiation, and evaporation for air velocities of0.11 < V < 0.33 m/s is determined experimentally and isexpressed as h = 5.05 kair Re1/3/D, where the diameter Dis the characteristic length. Oranges are cooled by refrigeratedair at 5°C and 1 atm at a velocity of 0.3 m/s. Determine(a) the initial rate of heat transfer from a 7-cm-diameterorange initially at 15°C with a thermal conductivity of0.50 W/m·K, (b) the value of the initial temperature gradientinside the orange at the surface, and (c) the value of theNusselt number.What is the length of tubing required to cool air from 80°C to 20°C via an isothermal tube maintained at 0°C? The tube diameter is 20 cm. Mean velocity of air is 4 m/s. Assume the flow to be fully-developed.