The plates of thickness 1.5mm is joint by two 3.0mm diameter rivets as shown in the figure. Calculate the maximum safe load F that can be applied if the shearing stress in the rivets is limited to 10 MPa and the bearing stress in the plates is limited to 15 MPA. Assume the applied load is uniformly distributed among the two rivets. 10mm F

The plates of thickness 1.5mm is joint by two 3.0mm diameter rivets as shown in the figure. Calculate the maximum safe load F that can be applied if the shearing stress in the rivets is limited to 10 MPa and the bearing stress in the plates is limited to 15 MPA. Assume the applied load is uniformly distributed among the two rivets. 10mm F

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Include the FBD of the Problem
can you help me with this
Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution Video. For the connection shown, the average shear stress in the 13-mm-diameter bolts must be limited to 270 MPa. Determine the maximum load P that may be applied to the connection. O 271 KN O 215 kN O 232 KN O 291 KN O 173 kN
The figure shows a flat hanger bar for supporting shop equipment in a factory. The bar is fixed to a support by means of a bolted connection. The main part of the hanging bar is 1.5 inches wide. This width varies up to 3.0 inches. A 1.0-inch diameter bolt transfers the hanger bar load to the two top bracket plates. Determine the allowable stress of the tension load P in the hanger in the following two instances: to. The allowable tensile stress in the main part of the hanger is 16,000 psi. b. The allowable stress load between the hanger bar and the bolt is 26,000 lb/pu.
Compute for (a) the force exerted on the bolt and rivets at joints A, B, and C and (b) the normal stress in member AD, if a force P of magnitude 300 N is applied to the handles of the bolt cutter shown in figure below, from which it has a uniform cross-sectional area of 2x10-4 m22x10-4 m². 300 N 24 mm D 12 mm B E 96 mm 24 mm 24 mm 460 mm- 300 N
Explanation required, Don't directly paste the solution from other site⚠️
The supporting wheel on a scaffold is held in place on the leg using a 4-mm-diameter pin as shown. (Figure 1) Figure 1 of 1 > Part A If the wheel is subjected to a normal force of P = 3.3 kN, determine the average shear stress developed in the pin. Neglect friction between the inner scaffold puller leg and the tube used on the wheel. Express your answer to three significant figures and include the appropriate units. Tavg= Submit Provide Feedback Value A Request Answer C Units ? Next >
2. For the joint shown in the figure, calculate: (a) The largest bearing stress between the pin and the members (b) The shear stress in the pin (c) The largest normal stress in the members 251N 25 AN 25 AN 25 AN
For the lap joint shown in the figure 1. Determine the maximum safe load P which may be applied if the shearing stress in the rivets is limited to 60 MPa 2. Determine the safe load P which may be applied if the bearing stress of the plate Is limited to 110 MPa (4-20 mm diameter rivet) O O →P
The right-angle bar is supported by a pin at B and a roller at C. what is the maximum safe value of the load P that can be applied if the shear stress in the pin is limited to 20,000 psi? the 3/4 -diameter pin is in double shear.
Brass Problem 3: A composite bar is made by attaching a copper rod of length 900 mm and diameter 30 mm and a brass rod of length 600 mm and diameter 45 mm as shown. A load of 20 kN is applied at 20°C. For unyielding supports, find the stresses in the materials when the temperature rises to 50°C. For copper, E = 120 GPa and a = 18 x 10-6 °C. For brass, E = 90 GPa and a = 20 x 106 °C. Copper 20 kN 900 mm 600 mm
@2 The support consists of solid brass post surrounded by a steel tube. Before the load is applied, the gap between these two parts is | mm. Given the dimensions shown in the figure, determine the greatest axial load that can be applied 0 the rigid cap A if the maximum allowable stress in brass is (Guiin)se = 150 MPa and the maximum allowable stress in steel is (Gun ) = 200 MPa. E, = 200 GPa and Ey,= 100GPa.