The plate shown in Figure 4.1 has a thickness of 25mm and is made of steel with density of 7200 kg/m³ 5 UTM a UTM 8 UTM y 110 mm 23 mm R10 mm R35 mm R15 mm 40 mm 150 mm А

Q: Q1: A rotating shaft carries four masses A, B, C, and D radially attached to it. The centers of mass…

A:

Q: Given data Stress=202 N/mm² Area = 3 mm² 2 Find Force.

A:

Q: QUESTION 26 A gate of a tank containing water and oil is kept in the closed position by applying a…

A:

Q: What size of receiver tank (gal) for a compressor is required if the pneumatic system is used to…

A: The size of the receiver tank required for the pneumatic system is approximately 588…

Q: Sir Edward decided to replicate the experiment of Torricelli (see diagram). He immersed a tube with…

A: d (diameter of tube)=3mmθ (angle formed at the mercury air interface)=51·σ (Surface tension at the…

Q: 2. An axial rod made of three different materials is fixed between two walls. (You can do this…

A: Given data:   E1 = E =10 MsiE2 =20 MsiE3 = 30 Msiα1 = 10 x 10-6 /°Fα2 = 20 x 10-6 /°Fα3 = 30 x 10-6…

Q: Find the value of stress Force=0.889 N Area 0.1 mm2

A: Given data : Force=F Area=A   Required: Stress

Q: The figure below shows a stored shaft where bearing A is a cylindrical bearing and bearing O is a…

A:

Q: Lever Problems - effort Resistance and Mechanical Advantage  R = 50 Lbs Length FE = .75 inch…

A: GivenR=50lbsFE=0.75inFR=12in

Q: Consider the system in (Figure 1) gure k-5 lb/in. <1 of 1 Determine the smallest amount the spring…

A: find :To determine the compression first we need to determine the vertical height of the point A…

Q: If force of 6 N Produce stress of 30 N/mm2. What is the cross sectional area on which force is…

A:

Q: Q2 A beam is supported at A and B as shown in Figure Q2. By neglecting the mass of the beam, (a)…

A: (a) To find: The support reactions. FBD: The free-body diagram is shown below.

Q: 1.5 in. 90 lb/ft 0.75 in. 800 lb. 3 ft. 3 ft. 6 ft. 4 ft.

A: Given Dataw=90fb/ftP=800lb

Q: As depicted below, to depress the on-off switch mechanism, a force of 5 N is applied to the handle.…

A: Given Applied load = 5 N To find Force in the switch S

Q: rs filled with oil if density psubscripto anc closed by two pistons. The small chamber on the right…

A: Given

Q: Find the weight of the floating can in figure below. 4cm €112 Water 7cm d=8cm

A:

Q: The non-linear spring shown in the image below has a stiffness, K, given by the equation: K= 7 - 5u…

A: Given: K = 7-5u To find: Extension of the spring

Q: The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the…

A: P= 48512 N Length of steel, Ls= 1.42 m Length of bronze, Lb= 2.36 m Area of steel, As= 639 mm2…

Q: If force of 6 N Produce stress of 30 N/mm2. What is the cross sectional area on which force is…

A:

Q: Q5: For the below shaded area, calculate Ixand Kx 130 mm 30 mm 30 mm mmt- 40 mn -40

A:

Q: Draw and label a entire Free-body diagram of THE BLOCK

A: Given: TO draw FBD of the block

Q: If W-100 N and u-0.5, then the friction force of the block shown in figure is

A: Solution:

Q: 3. Find the proper thickness of 900 mm cast-iron pipe under a 95m head of water with a working…

A:

Q: In the given figure below, a tube was supported at A and E by with a ball and socket and a wire at D…

A: Note: Dear Student! As per our guidelines, we are only allowed to answer three sub-parts of a…

Q: A 400-mm-long rod with a diameter of 4.5 mm is loaded with a 5000-N weight. If the diameter…

A:

Q: What force applied to a circular cross-section of diameter 7.5in will produce the same pressure with…

A:

Q: A circular cylinder with inside diameter of 10 cm which carries a compressive force equivalent to…

A:

Q: Solve this, Also find the tension In cord C

A:

Q: a 12mm thick steel tire has a width of 110mm and an internal diameter of 800mm. It is heated and…

A: Thickness, t= 12 mm Width, w= 110 mm Internal diameter of the tire, d= 800 mm Wheel diameter, D=…

Q: If force of 6 N Produce stress of 30 N/mm2. What is the cross sectional area on which force is…

A:

Q: Given: Find: A 0.5-inch diameter pole (L1-12 in, L2= 22 in) is loaded with three forces (two forces…

A: Pole diameter, D = 0.5 inch  L1 = 12 in, L2 = 22 in  P1 = 2.5 kip or 2500 lbs  P2 = 7 kip or 7000…

Q: In the Figure 3, the weight component parallel to the inclined surface can be calculated as: *…

A:

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.