The planetary gear A is pinned at B. Link BC rotates clockwise with an angular velocity of 8 rad/s, while the outer gear rack rotates counterclockwise with an angular velocity of 3 rad/s. Determine the angular velocity of gear A.

Q: From the frame loaded as shown. Solve the following if P = 15 P kN/m D 2P kN/m -8 m B H E 3P kN/m…

A:

Q: 5-54 The turbine develops 150 kW of power, which is trans- mitted to the gears such that both C and…

A: StressExplanation:Step 1:Step 2:Step 3: Step 4:

Q: find moment at point D, P=15kN

A: Given:- FBd of Beam;

Q: |A B C 3 m 2 m

A: There is a beam AC as follows:(a) Find the line of influence of the vertical reaction at point A.(b)…

Q: 5-38. The cantilevered jib crane is used to support load of 780 lb. If the trolley T can be placed…

A: Given : load supported by crane = 700 lb To Find : Determine support reaction at A and B ?

Q: From the compound beam shown, point Bis a pin and A is a roller. Compute the reaction at A. Compute…

A: Determine the reaction at A, B and C of the given beam.

Q: Determine the internal bending moment acting at point C. A -24 kN-m 24 kN-m 36 kN-m O 48 kN-m 4 m 12…

A:

Q: Q4/ The jib crane is supported by a pin at Cand rod AB. If the load has a mass of 3 Mg with its…

A:

Q: The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by…

A:

Q: Determine the reaction at support B for the simple beam shown. A 13 ft O a. 48kips O b.76kips O c.…

A: Given data:

Q: 1-49. The railcar lamp is supported by the -in.-diameter pin at A. If the lamp weighs 4 lb, and the…

A:

Q: 600 N Additional problem C: (Answer: A, 3.48 kN, Ay = 816 N, FBC = 4.36 kN) The overhanging beam is…

A: Given : Determine the horizontal and vertical component of reaction at A and B ?

Q: QUESTION 6 The compound beam shown has internal pin at point B. 150 lb 200 lb/ft 5/4 85 lb/ft 120…

A:

Q: The truck has a mass of 4-Mg and mass center at G. Determine the absolute maximum live moment…

A: Given:- To find:- Absolute maximum moment

Q: so IN 30 AN/in D B. 2 m 2 m

A: Given data:

Q: 4. Compute for the reaction at the roller B, the force components acting on the ball- and-socket at…

A:

Q: Q3. Determine the reactions at the pin ( A) and the roller ( B ). 80N 60 5m 150 N A 4 m 5m 3m FON Ý…

A: Balancing forces and moments

Q: Determine support reaction and maximum bending moment

A: Given data : Uniformly distributed load (w)=2 KN/mMoment (M)=50 KN/m

Q: The light right-angle boom which supports the 290-kg cylinder is supported by three çables and a…

A:

Q: point c is an internal hinge while a is a roller 1.) what is the vertical and moment reaction at…

A: As per guidelines we need to answer only first 3 subparts of questions so please repost rest…

Q: Determine the maximum moment at D due to a dead load of 5kn/m a moving live load of 20 kn/m and two…

A: We will draw ILD for moment at D.

Q: A 3.5 m D 7m B 2.5m *

A:

Q: Problem No. . Draw the influeice line for the vertical reaction and moment at B. 5m 5m 5m ... O .

A:

Q: 150 kN 120 kN 120 kN ww. 一 G B 6 m- -6 m- -4 m 21

A: Given:-

Q: Both shafts have the same diameter 2cm and are made of low quality steel G=77 GPa. A torque of 1200…

A: Given: Diameter of both the shafts: d=2cm=0.02m Length of the shaft AB: LAB=0.35m Length of the…

Q: 10–43. The shaft is made of A992 steel. It has a diameter of 25 mm and is supported by bearings at A…

A:

Q: 2- For the frame shown, determine the magnitude of the pin reaction at B. Neglect the weight of the…

A:

Q: 3. (a) The tapered shaft is confined by the fixed supports at A and B. If a torque T is applied at…

A:

Q: The bent rod is supported at A, B, and C by smooth journal bearings. Determine the magnitude of F2…

A: Free body diagram:-

Q: An AB lever is hinged at C and attached to the control cable at A. If a lever is found, a horizontal…

A: The given figure is shown below:

Q: The uniform rod has a mass of 100 kg. If the spring is unstretched when          θ = 60°, determine…

A: Draw the free body diagram.

Q: If each of the three links of the mechanism have a mass of 4 kg, determine the angle θ for…

A: Draw the free body diagram.

Q: If the intensity of the distributed load acting on the beam is w = 3 kN/m, determine the reactions…

A: It is a determinate beam so reaction can be calculated by equilibrium equation.

Q: The bent rod is supported at A, B, and C by smooth journal bearings. Determine the magnitude of F…

A: Given: The bent rod is supported at A, B, and C by smooth journal bearings. The magnitude of F is to…

Q: The compound beam is pin supported at C and supported by a roller at A and B. There is a hinge (pin)…

A: Given:- A=8B=6C=8Y=29 To find:- Reactions at the supports Shear force at (A+4) ft left of C Shear…

Q: 30KN/m sokwlm Zim 3m im 4m

A: Given data in question  Simply supported beam  UVL UDL Span member length  To find out  Reactions…

Q: A unit load will pass in the simple beam shown. 1) The absolute reaction @ A and C when the unit…

A:

Q: For the simply supported beam shown, draw influence lines for moment at C (12-ft from support A),…

A: when the unit load at A and B then bending moment at C equal to 0 .and if the unit load at C then…

Q: Determine the external reaction at the roller support in kN. Select one: a. 280 b. 30 c. 310 d. 120

A:

Q: Two beams at 6 meters in length each are arranged so that the reactions at A, B, and D are the…

A: