The piston rod of an air operated press is to exert a maximum force of 20 kN. During the application of the force, the air pressure is maintained at 700 kPa. Assume the piston rod length to be 760mm, with its right hand end pin connected to the operating lever and the piston end of the rod fix ended. If the piston rod diameter is 15mm, determine its slenderness ratio

The piston rod of an air operated press is to exert a maximum force of 20 kN. During the application of the force, the air pressure is maintained at 700 kPa. Assume the piston rod length to be 760mm, with its right hand end pin connected to the operating lever and the piston end of the rod fix ended. If the piston rod diameter is 15mm, determine its slenderness ratio

Name: The piston rod of an air operated pressis to exert a maximum force of
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: The piston rod of an air operated pressis to exert a maximum force of 20 kN.During the application of the force,the air pressure is maintained at 700kPa. Assume the piston rod length tobe 760mm, with its right hand end pinconnected to the operating

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Calculate the value of the hydrostatic pressure force acting on the septal septum shown in the diagram, given that the diameter of the diaphragm D = 1.5 and its length I = 1 he Fx
Determine : 1.The sense and magnitude of the stresses induced in the composite if it is not restrained. 2. The sense and magnitude of the stresses induced in the composite if it is partially restrained with an allowed free expansion of 0,3 mm.
i need the answer quickly
2. A hopper having a mass of 2250 kg is designed to hold a bulk load of salt having a mass of 9250 kg. The hopper is to be suspended by four rectangular straps, each orientated 20 degrees from the vertical and each carrying one fourth of the load from the hopper+salt. Steel plate, with a thickness of 12 mm is to be used to make the straps. What should the minimum width of the straps be in order to limit the stress to 120 MPa, whereby straps are available in increments of 5 mm widths. 20deg strap hopper
Dear expert solve correctly all parts Including last one
A cylinder has an internal diameter of 230 mm, has walls 5 mm thick and is 1 m long. It is found to change in internal volume by 12.0 × 10-6 m³ when filled with a liquid at a pressure p. If E=200 GN/m² and v = 0.25, and assuming rigid end plates, determine: (a) the values of hoop and longitudinal stresses; (b) the modifications to these values if joint efficiencies of 45% (hoop) and 85% (longitudinal) are assumed; (c) the necessary change in pressure p to produce a further increase in internal volume of 15%. The liquid may be assumed incompressible.
A circular cross section cylinder containing oil, has an internal bore of 30cm diameter. The cylinder is 1cm thick If tensile stress in the cylinder must not exceed 75MPa, maximum load P which may be supported on piston sliding in the cylinder is
Q2: A spacer is turned from Aluminum alloy with elasticity modulus of 78 GN/m?. The spacer has a diameter of 28 mm and a length of 245 mm. both measurements being made at 20°C. The temperature of the spacer is then increased to 100 °C, the natural expansion being entirely prevented. Taking the coefficient of linear expansion to be 18 x 10-6 °C. Determine the compressive load on the spacer.
Please show full solution please, thank you
A railroad car and its cargo have a total weight of 50 kips. The car is sup 5-50 ported on eight wheels, each of which has a diameter of 25 in. If the co cient of rolling resistance is 0.015 in. between the wheels and the trach and the wheels share the load equally, determine the magnitude of the ho izontal force required to overcome the rolling resistance of the wheels.
A 90 degrees angle on a 1/2 inch water pvc pipe. determine the force on the angled pipe if the water prusser is 30kpa.
A spherical pressure vessel has a 1.33-ft inner radius and 0.19-in. wall thickness. If the working tensile stress of the material is 5594psi, determine the maximum allowable internal pressure (in psi). Add your answer