The pins on the frame at B and C each have a diameter of 0.28 in. If these pins are subjected to double shear, determine the average shear stress (ksi) in pin Bwhere: P1 =595 lbs; P2 =327 lbsFinal answer should have 2 decimal places The pins on the frame at Band C each have a diameter of 0.28 in. If these pins are subjected to double shear,determine the average shear stress (ksi) in pin Bwhere: P1 =595 lbs; P2 =327 IbsFinal answer should have 2 decimal places-3 ft-3 ftP13 ftB,1.5 ft1.5 ft3 ftP2

Please refer the attached image for complete solution. THANK YOU.

The pins on the frame at Band C each have a diameter of 0.28 in. If these pins are subjected to double shear, determine the average shear stress (ksi) in pin B where: P1 =595 lbs; P2 =327 Ibs Final answer should have 2 decimal places -3 ft -3 ft P1 3 ft B, 1.5 ft 1.5 ft 3 ft P2

The pins on the frame at Band C each have a diameter of 0.28 in. If these pins are subjected to double shear, determine the average shear stress (ksi) in pin B where: P1 =595 lbs; P2 =327 Ibs Final answer should have 2 decimal places -3 ft -3 ft P1 3 ft B, 1.5 ft 1.5 ft 3 ft P2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: determine the tensile stress in each segment of the bar shown. Segment AB cross section 2in x 2in.…

A: Segment AB cross section 2in.×2in. Segment BC cross section with a dia. of 1.75in. Tensile load (P)…

Q: A wide-flange beam (see figure) is subjected to a shear force V. t- 0 Using the following dimensions…

A: Given t = 0.5 in h1 = 8.4 in Maximum shear stress = 6496.51 psi Minimum shear stress = 5414.99 psi V…

Q: Problem 3 in the steel structure shown, a 6-mm-diamter pin is used at D and 10-mm-diameter pins are…

Q: For the truss and loading shown, determine most economical cross-sectional area (in in2) of member…

Q: By internal couple method, what is the maximum stress on the steel side of the transformed section?…

A: Given data: m=9

Q: AW18 × 40 standard steel shape is used to support the loads shown on the beam. Assume P = 18 kips, w…

A: Given data, P = 18 kips W = 5.8 kips /ft L(AB) = 4.8 ft L (BC) = 4.8 ft L (CD) = 16.4 ft To find…

Q: 3/4 130 mm O O O 25 mm 25 mm

A: Fbd is shown below Upper plate , bolt and lower plate fbd Bolt is being cut by one plane as they…

Q: DETERMINE THE LARGEST LOADP THAT CAN BE APPLIED TO THE BARS OF THE LAP JOINT SHOWN IN THE FIGURE.…

Q: Given the truss and loading shown below, determine the stress at member Al if Pu = 18.375 Kips and…

Q: In the steel structure shown a 6 mm diameter pin is used at C and 10 mm diameter pin is used at B.…

A: Given:Diameter of pin at C is 6mmDiameter of pin at B is 10 mmRequired:Largest P applied

Q: A PROB. 1.8-12 a 2P B (a) D XII Gusset plate Rivet (b) Section

Q: Question-03: The steel tie bar shown in Figure 2 is to be designed to carry a tensile force of…

Q: Set P₁ = 1.6 kN and P₂ = 1.2 kN. (EFigure 1) Figure 30° 3 m D P 30/ 3m P₂ ▼ Determine the force in…

Q: Calculate each of the following under 20 kN load on a structure given below where all pins have a…

Q: Find the normal stress of members CD and CE of the truss shown. Cross sectional area of the members…

Q: A W18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 25 kips,…

A: W18×40 section Determine the magnitude of maximum bending stress in the beam.

Q: AT section has the dimensions given in Fig. ..Show that the neutral axis is 3 inches below the top…

A: Given data : INA = 166.7 in.4 Tensile stress at the bottom of the flange = 1000 psi This is a…

Q: Given the truss and loading shown below, determine the stress at member FC if P₁ = 18.375 Kips and…

Q: Steel links having the cross section shown are available with different central angles B. Knowing…

Q: For the steel truss and loading shown, determine the deformation (in inches) of member BD, knowing…

A: First calculate the member force in BD using the method of sections. Then using the HOOKES formula…

Q: Given the following, please solve this problem step by step so I can understand.

Q: 8 kips 4 kips 4 kips d, =2" 15 kips 15 kips -d2 =1.5" !0 kips 20 kips d, =3" A Fig. for Problem #2

A: There are 3 bars AB, BC, CDThe forces on those bars are also given.Diameter of bar CD, d1 = 2…

Q: Which stress element below correctly shows the normal and stress al point? which located at the top…

Q: Three plates are welded together to form the section shown. Dimensions of the cross section are b=…

Q: or the beam shown, determine the stress in each rod if the load P= 50 kN is applied. Bronze Steel…

Q: D -a C- B F a- K ·a G L

A: To determine the zero force members in the given truss - Zero force member - If three members form a…

Q: FOR THE LAP JOINT SHOWN, DETERMINE THE MAXIMUM SAFE LOAD 'P' WHICH MAY BE APPLIED IF THE SHEARING…

Q: Given the truss and loading shown below, determine the stress at member AB if Pu = 18.375 Kips and…

A: Given:- Pu=18.375 kipsArea of member AB isA=23 in2 To find:- Stress in member AB

Q: Determine the maximum permissible value of T provided the allowable shearing stresses in brass and…

A: Given:- ζball = 70 MPaζsall = 110 MPaGs = 80 GPaGb = 40 GPadi = d = 70 mm, d0 = 90 mm…

Q: AB kN AC kN 3. Simply supported beam with rectangular section is subjected to the loads shown in the…

A: Finding out normal stresses.

Q: For the truss and loading shown, determine most economical cross-sectional area (in in2) of member…

Q: Problemt The detail of a truss at the support is glued as shown. Given: shearing stress = 800 kN/m?…

Q: se that in addition to the 2.00-kN downward force acting at point D, a 1.85- ownward force acts at…

A: To find force in member AB, AC

Q: X Incorrect Three plates are welded together to form the section shown. Dimensions of the cross…

Q: For the truss shown, calculate stresses in members AC, AB and BE. Cross section of each member 16…

Q: Three plates are welded together to form the section shown. Dimensions of the cross section are b =…

A: Given: The value of b is 3.6 in. The value of d is 10.8 in. The value of a is 2.3 in. The value of t…

Q: A short prismatic member is subjected to load P- 100 kips at comer shown by Red Dot as shown in…

A: Given: Load, P= 100 kips A1=3×12=36''y1=122=6''A2=3×12=36''y2=122=6''A3=9×3=27''y3=32=1.5''

Q: QI: Find the normal stresses at sections A-A, B-B, C-C, and, D-D for the body as shown in figure…

Q: Assume that 4-18mm diameter rivets join the plates that are each 120mm wide. The allowable stresses…

Q: Problem 01.054- Analysis of an inverted T-frame In the steel structure shown, a 6-mm-diameter pin is…

Q: For the truss shown, calculate the stress in member BD. The cross-sectional area of each member is…

A: We have to find out the stress in member BD

Q: If the applied load "P" causes the point C to be displaced downward by &c=1 mm, determine the normal…

A: LAC = 210 mmLBC = 480 mm

Q: A B Figure 1

Concept explainers

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.

Question

The pins on the frame at B and C each have a diameter of 0.28 in. If these pins are subjected to double shear, determine the average shear stress (ksi) in pin B

where: P1 =595 lbs; P2 =327 lbs

Final answer should have 2 decimal places

The pins on the frame at Band C each have a diameter of 0.28 in. If these pins are subjected to double shear,
determine the average shear stress (ksi) in pin B
where: P1 =595 lbs; P2 =327 Ibs
Final answer should have 2 decimal places
-3 ft
-3 ft
P1
3 ft
B,
1.5 ft
1.5 ft
3 ft
P2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The strain at point A on the bracket has components €g = 330 (10-6), e, = 560 (10-6), Yxy = -570 (10-6), e; = 0. Correct Part B Determine the maximum shear strain in the x - y plane. = 6.15x10-4 'in-plane Submit Previous Answers Correct Part C Determine the absolute maximum shear strain. (Figure 1) Figure < 1 of 1 vec -4 Yaa = 7.99 • 10 max Submit Previous Answers Request Answer X Incorrect; Try Again
Three plates are welded together to form the section shown. Dimensions of the cross section are b= 4.7 in., d = 14.1 in., a = 2.8 in., and t= 0.5 in. For a vertical shear force of V = 42 kips, determine the shear flow through the welded surface at B. B a b Answer: kip/in.
6
a) Two bars of different size form a pin-connected frame that supports a Load 'P' at point A as shown in the Fig. 3. What safe load P (kN) can be applied if the allowable stress of 120 MPa is not to be exceeded? Assume buckling has been prevented. Allowable stress is based on a factor of safety of 2.0. Cross sectional area of the rods AB and AC are given in the adjacent table as per last digit of Roll number. What is the failure load? Last digit of Area of AB | Area of AC Roll No. 1, 2, 4 & 7 200 mm 230 mm“ 3, 6 & 8 160 mm- 190 mm² 5, 9 & 0 180 mm 210 mm 2400 1600 Fig. 3 b) Two square bars are of equal length but have different size as shown in Fig. 4. Compare the maximum stress in the two bars if they are to receive the same input of energy from axial load. Given, m = (2 + last digit of your roll number). 2a 5.x m.x Fig. 4 last digit of roll=1
The pins on the frame at B and C each have a diameter of 0.28 in. If these pins are subjected to double shear, determine the average shear stress (ksi) in pin B where: P1 =572 lbs; P2 =346 lbs Final answer should have 2 decimal places
QUESTION 6 A bar of uniform cross sectional area- 168.290 mm2 is fully fixed at supports A and B and subjected to axial loads P and F along its length applied in the directions shown LAB 6m, LBC-3m A B F If the value of P is 23kN and that of F is 13kN, determine the stress acting in member AB, identifying a compressive stress ( in N/mm2) as negative and tensile stress as positive. Present your answer to three decimal places.
#5 will upvote anyone who will answer correctly. thanks
Find the maximum tensile and compressive normal stresses in the beam below. Mark their locations along the height of the cross section and along the length of the beam. (Note: The centroid is located 4.423in from the top of the cross section and I= 42.0 in*.) W= 1k/ft 6k 10' 5' 4423" 8.75 M (k-t) -12.5 Cross section
4
d = 100 mm x = 50 MPa Fig. 01 d = 75 mm T = 80 MPa 02 Determine the smallest allowable diameter brass rod, of length 3.0m, if the rod is to be twisted through one complete revolution without exceeding a shearing stress of 50 MPa. For brass, G = 39 GPa.
PLEASE DRAW THE FBD. DO NOT COPY YOUR ANSWER FROM OTHER. I WANT TO SEE THE FBD OF INDIVIDUAL DEFORMATIONS ON HOW YOU WILL ARRIVE ON YOUR ANSWER. DRAW FBD ON EACH PLEASE. NOT ONLY ONE FBD
load 1: 60 load 2: 50