The parting line in injection molding is which one of the following: (a) the lines formed where polymer melt meets after flowing around a core in the mold, (b) the narrow gate sections where the parts are separated from the runner, (c) where the clamping unit is joined to the injection unit in the molding machine, or (d) where the two mold halves come together?

Q: For a powder binding process that mixes a 1:2 volume ratio mixture of semi-crystalline polyethylene…

A: In this problem, we will calculate the percent crystallinity of the manufactured parts at the given…

Q: Which law of thermodynamics best apply to compression molding machine? Explain why.

A:

Q: The RIM (Reaction Injection Molding) process does not require the plastic materials to be heated…

A: we will discuss RIM

Q: The parting line in injection molding is which one of the following: O the lines formed where…

A:

Q: An extruder barrel has a diameter of 4.0 in and an L/D ratio of 28. The screw channel depth = 0.25…

A: As per our guidelines, we can answer only one question. Kindly post the remaining question in…

Q: Which of the following plastic and composite materials processing is most suitable for the…

A: polymer automotive body panels are widely applied in automotive industries due to their high…

Q: What kind of system is compression molding machine? open, closed, or isolated? Explain.

A: Concept: Open system: There is exchange of both heat and mass transfer.  Closed system:There is…

Q: Long plastic products with uniform cross sections are readily produced by the extrusion process.

A: Answer IS TRUE

Q: What are the benefits of using a chain in place of a rope? What are the concerns about dropping an…

A: The advantages of having chain drive over rope are given below. a) In Power transmission through…

Q: Figure 9 is the adsorbent natural gas (ANG) vehicle tank to hold natural gas in an adsorbent at low…

A: In the vehicle sector, there has been a significant increase in the need for lightweight materials…

Q: For a powder binding process that mixes a 1:2 volume ratio mixture of semi-crystalline polyethylene…

A:

Q: nufacturer was asked to pro

A: Casting Process:- A liquid substance is often poured into a mold that has a hollow chamber in the…

Q: What is Blow molding process? Describe extrusion blow molding and injection blow molding. What are…

A: Blow moulding: - Blow moulding is the joining and forming of the two plastic objects together. This…

Q: In a particular extruder screw the channel depth is 2.4 mm, the screw diameter is 50 mm, the screw…

A:

Q: A pudding mix is being formulated to achieve a total solids content of 20% in the fi nal product.…

A:

Q: 2. A mold sprue is 180 mm long, the cross-sectional area at its base is 2.4 cm?. The sprue feeds a…

A:

Q: Process of forming metal powder by directing molten metal through an orifice after which it is break…

A: Process of forming metal powder by directing molten metal through an orifice after which it is break…

Q: What materials should not be used for injection molding?

A: Injection molding: It is the process soft material (malleable enough or past form) is injected at…

Q: 3.- You have rifampicin crystals with an average size of 0.3 mm in diameter, to prepare hard gelatin…

A: given; which mill would you use for this particle size reduction process. what meshes would you use…

Q: 2 Which of the following best describes the Powder Forming process? (A) Materials are heated and…

A:

Q: During the injection molding the mold for shaped plastics are a. pressed O b. blown Ос. closed O d.…

A: Ans) option a Pressed Injection moulding is a manufacturing process that allows for parts to be…

Q: Justify the addition of lubricants to powders in blending operation

A: Blending operation is defined as the process in which we mix all ingredients to get a homogeneous…

Q: a.State and describe the term i. co-extrusion b. Differentiate between single and twin-screw…

A: Note: Since you have posted multiple independent questions in the same request, we will solve the…

Q: 12) Assuming injection molding pressures of 10kpsi, estimate the die clamping force required for…

A: Disk diameter=1.5 inch Pressure P=10kpsi Runner area= 5.0 in2 there 10 identical which means Area of…

Q: An extruder is expected to produce 4kg of filament per hour, the barrel has a diameter of 19.05mm…

A: The material that gets the deformation of plastics under the action of various forces and causes the…

Q: An extruder barrel has a diameter of 4.0 in and an L/D ratio of 28. The screw channel depth = 0.25…

A: As per our guidelines, we can answer only one question. Kindly post the remaining question in…

Q: Viscosity is an important property of a polymer melt in plastics shaping processes. Upon what…

A: The parameters on which viscosity depends.

Q: The part shown in Figure is to be pressed from fine copper powders using a compaction pressure of…

A:

Q: An extruder is expected to produce 4kg of filament per hour, the barrel has a diameter of 19.05mm…

A:

Q: Consider a single screw melt extruder with the following dimensions: D = 6.0 cm, L = 60.0 cm, H =…

A: Given       Viscosity = 500 Ns/m2         Density = 900 kg/m3 Discharge, Q = 5 kgg/hr   Diameter, d…

Q: Explain the extrusion blow molding in detail.

A: Extrusion blow molding is also coined as a “blow forming  “  manufacturing process by which hollow…

Q: Mold venting design objectives include (). A release compressed air B. contain plastic melt C.…

A: As per given question  Mold venting design objectives include

Q: I only need the answer to question 2. I provided the correct answer for question 1 1)An extruder…

A: From the question, we have Diameter = 4.0 in  L/D ratio = 28 Screw channel depth = dc= 0.25 in Pitch…

Q: Of the three open mold processes for polymer matrix composites described in the text, hand lay up is…

A:

Metal Casting

Metal casting is described as a manufacturing process in which a mold cavity is produced by sand, and molten metal is filled inside a mold cavity. The desirable shaped object is achieved after the solidification of molten metal. Large metal objects like machine beds, motor bodies, and others can easily be manufactured using metal casting. The place or shop where metal casting is performed is called foundry.