The over all draft loss of steam generating unit is 410 mm water. Air enters at 101.325 kPa, 26 degree Celsius and the average flue gas temperature is found to be 260 degree Celsius. If nodraft fans are to be installed, what is the height of the chimney? Assume R constant for gas is 0.277 kJ/kg-K

Q: How about the relative error and percentage error of the volume?

A:

Q: Use water as a drilling mud to drill a well to a depth of 3000 feet , calculate the pressure…

A: This question is based on pressure gradient. The data given are: Depth = 3000 feet

Q: Regarding amorphous plastics, explain why they tend to have higher tensile strength when deformed…

A: Amorphous plastics have no specific order and pattern in their molecular structure. Thus, the…

Q: Use equations and words to describe how stirring a solution will affect the mass-transport limited…

A: The current that flows through a solution at any time is a direct measure of the rate of the…

Q: A 2 mm diameter glass tube is inserted into an open glass of water (contact angle between the tube…

A: Diameter of glass tube =  2 mmContact angle,  = 0

Q: A B Rate of deformation, duldy Shear stress, 7

A: There are several properties defined for fluid such as density, specific gravity, viscosity, etc. In…

Q: Is pinch point always located at the feed stage?

A: The location of the pinch point is to be mentioned.

Q: Explain steady flow in relation to fluid mechanics.

A:

Q: Mention some key considerations during installation of a cyclone seperator?

A: Cyclonic separation is a means of separating different liquid phases, or, separating particles from…

Q: A machine rotates at 8800 rpm and decelerates at 95 rad s^-2 . Find how long it takes the machine to…

A: The objective of the question is to find out the time it takes for the machine to stop from its…

Q: crystallization mechanism,

A: Crystallization is a process in which mass transfer of solute takes place from the liquid solution…

Q: Calculate the volume of an HCP unit cell in terms of cell edge (a) and height (c).

A:

Q: Given a 35% mixture, what will be the time of flow? * O 43.5% O 41.5% O 6.6% 6.5%

A:

Q: Why do positive displacement pumps cause pose more overpressure hazard compared with centrifugal…

A: In a positive displacement (PD) pump, a fixed volume of liquid is trapped inside an enclosed chamber…

Q: What is the difference between the loading point and the flooding point in a packed column?

A: Loading Point and flooding points refer to the operating conditions of packed column.

Q: 10 - 10 -10 10 120 10 10 50 80 10 160

A: distance H from the bottom of the base plate  i.e. y co-ordinate of the centroid we have to…

Q: Describe 1st angle and 3rd angle Projections?

A: 1. First Angle Projection : In the first angle projection, we can placed the object in the 1st…

Q: In the plate and frame filter press, by plotting the filtrate volume as a function of time per…

A:

Q: Convert a viscosity of 20 (g)/(cm)(s) to the American Engineering units (Ibr)(hr)/(ft?)

A: Given viscosity is 20 g/cm s Viscosity unit of g/cm s have to convert into American Engineering unit…

Q: What is a  vane-axial cyclone seperator?

A: This question is from cyclone separators which form an important part in separation processes. The…

Q: It is important to balance the tubes OPPOSITE to each other. Failure to do so may lead to INCOMPLETE…

A: Centrifuge device uses centrifugal force to separate the different components of a liquid. In this…

Q: What is a flexible wedge gate used for

A:

Q: Why does the fluid drop in the fluid level measurement experiment when the pump is turned off?

A: In a typical fluid level measurement experiment, the pump is used to recirculate the fluid in a…

Q: Q.3 a). A tensile stress is to be applied along the long axis of a cylindrical brass rod that has a…

A: The magnitude of load is to be calculated.

Q: There are two previously undeformed cylindrical specimens of Aluminum alloyithat are strain hardened…

A:

Q: 2. List the most important pipe friction formula.

A: Introduction: The friction loss in uniform, instantly sections of pipe, called "major loss", is…

Q: What is viscosity

A: A fluid is defined as a liquid or gas that flows or deforms continuously when an external force or…

Q: Explain the concept of fluid flow and its significance in chemical engineering processes.

A: The study of fluids, which includes liquids and gases, is known as fluid flow. Fluids may flow and…

Q: Using a flow chart, show how a lubricant oil with high viscosity index can be manufactured from…

A: In petroleum industries, Crude oil is a type of fossil fuel that is a naturally occurring petroleum…

Q: If the time of flow of the given mixture is 50 seconds, what is the composition of the mixture? * O…

A:

Q: Explain the friction between the mater (soled with soled, liquid with liquid)?

A: Motion: Motion is the phenomenon in which an object changes its position over time. Motion is…

Q: production of paper from ground nutshell complete flow chart

A: In this question flow chart of production paper from ground nutshell is to be discussed.

Q: When we change the fluid package from one package to another, does the temperature and pressure…

A: When we change the fluid package from one another then the following properties will change such…

Q: How to calculate pressure drop in Gas pipe , formula ,

A: When gas flows in pipes, the pressure drop is caused due to following reasons:Friction in the…

Q: In a trayed tower,what are the two types of flooding, and which is more common?

A: The two types of flooding in the tray tower are to be mentioned along with the more common out of…

Q: The following are not commonly made from composites: Select one: a. Desks b. Canoes c. Bridges d.…

A: Ans.  Composites is the material that are made up of two or more materials. Which on combining they…

Q: Cl the dimensions were all the same, which chocolate can withstand the greatest load? D. Which has…

A: C. The chocolate that can withstand the greatest load is to be mentioned.

Q: Describe the factors that affect fluidization.

A: Factor that have an effect on fluidization are  fluidization parameter (calculated through inlet air…

Q: Explain and describe possible factors that may affect fluidization.

A: Fluidization parameter (calculated via inlet air drift fee and rotor speed), stress distinction over…