The open tank filled with a liquid in full as shown in the figure below has the height of h = 6.00 m. The inclined angle of the inclined wall is = 45.00 °. The width (perpendicular to the screen) of the inclined wall is w = 20.00 m. The specific weight of the liquid is = 9.81 kN/m3. (1) For the inclined wall, determine the average pressure on it._________ (kPa)

The open tank filled with a liquid in full as shown in the figure below has the height of h = 6.00 m. The inclined angle of the inclined wall is = 45.00 °. The width (perpendicular to the screen) of the inclined wall is w = 20.00 m. The specific weight of the liquid is = 9.81 kN/m3. (1) For the inclined wall, determine the average pressure on it._________ (kPa)

Name: The open tank filled with a liquid in full as shown in the figure belo
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: The open tank filled with a liquid in full as shown in the figure below has the height of h = 6.00 m. The inclined angle of the inclined wall is = 45.00 °. The width (perpendicular to the screen) of the inclined wall is w = 20.00 m. The specific we

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.121P: One side of the container has a 03-m square door that is hinged at its top edge. If the container is...

See similar textbooks

Similar questions

The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
Q.1: An inclined, circular gate with water on one side is shown in the figure below. Determine the total hydrostatic force acting on the gate and the location of the center of pressure. Water surface 1.5 m 60 Gate Side view Gate Top 1 m view Q.2: In the figure shows a curved surface LM, which is in the form of a quadrant of a circle of radius (2.4 m), immersed in the water. If the width of the gate is unity, calculate the horizontal and vertical components of the total force acting on the curved surface. Free water surface 1.2 m 2.4 m TTTTTTTM Curved surface
A 10000 litre water tank is placed on a building roof and filled to capacity. The empty tank has a mass of 550kg. It is supported on 4 feet, each of which is a 300 x 300 mm steel plate. What is the pressure exerted by each plate, in Pa? (Round your answer to 2 significant figures)
Q1) The inverted U-tube manometer of Fig. contains oil (SG 0.9) and water as shown. Find The pressure differential between pipes A and B. If a =1.5 m , h= 90 cm and b=2 m. Oil a m b Water
An open tank contains 5.6m of water covered with 3.4m of kerosene (S.G=0.80). Find the pressure at the interface and at the bottom of the tank
A B с OIL WATER 1.0M 0.5m In the tank open to the atm. shown in the figure below, there is on oil layer 1 meter high on a 0.5 meter high water layer. Since pont & is in the Middle of paints A and C. calculate the pressures at points A, B, C, D in Kla. (Density of water 1000 kg/m³, density of oil 800 kg/m³)
ВЗ. A circular plate of diameter 3 m is vertically placed in water in such a way that the centre of the plate is 9.4 m below the free surface of water. Find the total pressure & center pressure on the plate. Draw the diagram neatly. Total Pressure on the circular plate (in N) Centre of Pressure on the circular plate (in m)
An 8-in.-diameter piston is located within a cylinder that is connected to a 0.5-in.-diameter inclined-tube manometer as shown in the figure. The fluid in the cylinder and the manometer is oil (specific weight = 57 Ib/ft3). When a weight, W, is placed on the top of the cylinder, the fluid level in the manometer tube rises from point (1) to (2). How heavy (in Ib) is the weight? Assume that the change in position of the piston is negligible. W 6 in. (2) (1) Piston Oil 30°
Open to Closed top What is the maximum gage pressure atmosphere in the odd tank shown in the figure? Where will the maximum pressure occur? What is the hydrostatic force acting on the top (CD) of the last chamber on the right-hand side of the tank? Assume T 10°C 1 m Plan view (view E-E) Open to atmosphere B 2 m 1m 1m 1m Air Air 2 m S= 3.0 Water 1 m Liquid Elevation view
Q 3 :A plate ABCD hangs in water from one of its comers (as shown in the figure). Determine the total pressure on the plate and the position of the center pressure? Water Surface 10 m 5m 7 B 612 C _5 m O
A multifluid container is connected to a U-tube, as shown in the figure. For the given specific gravitles and fluid column heights. determine the gage pressure at A. Also determine the height of a mercury column that would create the same pressure at A. The column heighth of oil is 86 cm. The specific gravitles are 1.26 for glycerin and 0.90 for oll. We take the standard density of water to be Pw=1000 kg/m³ and the specific gravity of mercury to be 13.6. h 35 cm 18 cm Į Oil SG-0.90 Water Glycerin SG-1.26 90 cm 15 cm The gage pressure at A is kPa. The height of a mercury column that would create the same pressure at A is cm.
Q3) Find the horizantal and vertical pressure force exerted on the gate (AB) of the tank. I [Tank length = 3.5 m). P=15kq Water r=2m