The motor shown supplies 126 hp at 1340 rpm at A. Shafts (1) and (2) are each solid 1.86-in.-diameter steel [G11400 ksi] shafts w lengths of L₁ = 79 in. and L₂ = 105 in., respectively. Assume Ng-27 teeth and N-42 teeth. The bearings shown permit free rotation the shafts. (a) Determine the maximum shear stresses T₁, T2 produced in shafts (1) and (2). (b) Determine the rotation angle DA of gear D with respect to flange A. Nc NB TD

The motor shown supplies 126 hp at 1340 rpm at A. Shafts (1) and (2) are each solid 1.86-in.-diameter steel [G11400 ksi] shafts w lengths of L₁ = 79 in. and L₂ = 105 in., respectively. Assume Ng-27 teeth and N-42 teeth. The bearings shown permit free rotation the shafts. (a) Determine the maximum shear stresses T₁, T2 produced in shafts (1) and (2). (b) Determine the rotation angle DA of gear D with respect to flange A. Nc NB TD

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The shaft shown in the figure is machined from AISI 1040 CD steel. The shaft rotates at 1600 rpm and…

Q: The solid steel shaft AB (diameter 19mm) and CD (diameter 25mm) are connected by gears. For each…

Q: A standard 25-HP electric motor operates at 1800-RPM. If the motor is connected to a pump in the…

A: The power available, P = 25 hp The speed of motor, N = 1800 rpm The diameter, d2 = 1.25 in The…

Q: Problem 2: A solid circular drive shaft with a diameter of 0.5" transmits a torque of 200 in-1bf and…

A: The diameter of the shaft, Transmitted torque, The maximum bending moment, The yield strength of…

Q: Problem 5-57: The turbine develops 150 kW of power, which is transmitted to the gears such that C…

A: Given data as per the questionpower developed =150 kwdiameter of shaft =100 mm =0.1 mRotational…

Q: An input shaft of a gearbox with motor power P = 7 kW and rotation number n = 1300 rpm. The diameter…

Q: A standard 25-HP electric motor operates at 1800-RPM. If the motor is connected to a pump in the…

A: The power available, P = 25 hp The speed of motor, N = 1800 rpm The diameter, d2 = 1.25 in The…

Q: Two motors deliver 119 hp each at 1000 rpm to shafts at A and D. The shaft transmits torque through…

A: Data given- Motor deliver = 119 hp N = 1000 rpm Shear modulus = 11 × 103 ksi

Q: A standard 25-HP electric motor operates at 1800-RPM. If the motor is connected to a pump in the…

A: The power available, P = 25 hp The speed of motor, N = 1800 rpm The diameter, d2 = 1.25 in The…

Q: Bearing stress 5. Please provide proper discussion and illustration also complete solution and…

A: given; transmitting force(F)=50KN =50*103Nshear stress on…

Q: left and right bearings. The C is 600 mm and that of gea e between the centre line of . The shaft…

Q: Form the figure below, the power transmission shaft shows the forces acting on it carrying two…

Q: The mean diameter of the driving pulley for a vee-belt drive with two belts is 110 mm. The pulley…

A: diameter of pulley (d) = 110 mm no of belt = n = 2 groove angle = 2β = 45° = β = 22.5° power…

Q: A solid constant-diameter circular shaft is subjected to the torques of TA = 440 Ib-ft, TB = 1030…

Q: (a) List down 2 assumptions needed in designing the shaft in Fig. 3. Design the minimum allowable…

A: DefinitionBending Moment:If an object undergoes a bend about its certain axis due to some tendency…

Q: For the step-shaft of Ex. 6–6, it is determined that the fully corrected endurance limit is Se = 280…

Q: The chain drive is mounted in the center for the system shown in figure.It can transmit 15 hp at a…

Q: A steel cable is supporting a load of F = 9800 lb and is wrapped around a drum attached to gear A as…

Q: A solid constant-diameter circular shaft is subjected to the torques of TA= 480 lb-ft, TB = 1030…

Q: Torque =230 N-m

A: The torque for designing a rigid flange couple is given as, T=250 N-mT=250×103 N-mm The number of…

Q: A compound steel [G= 94 GPa] shaft consists of solid 28-mm-diameter segments (1) and (3) and tube…

A: Shear modulus of the compound steel (G): 94 GPa (or 94 x 10^9 Pa)Diameter of solid segments 1 and 3…

Q: 2. A steel shaft rotating at 600 rpm is supported by two bearings as shown. E=30 Mşi, d=1.0" (inch),…

A: Assume the shaft is static initially and evaluate the reaction forces at bearing supports.Consider…

Q: 3. Knowing the rotation speed: n=300r/min and the power of applying on each wheel: P₁-200kW. P-50kW,…

A: Given Data: n=300 rpmP1=200 kWP2=50 kWP3=50 kWP4=100 kWτall=120 MPaLAB=LBC=LCD=1.5 mR=20 mm To…

Q: QUA four stroke internal combustion engine has the following specifications: Brake power-7.5 kW;…

A: four stroke engine Brake power (B.P.)= 7.5 KWSpeed (N)= 1000 rpmImep (Pm)= 0.35 N/mm2max. gas…

Q: The coupled shafts shown are transmitting 270 hp at 600 rev/min. The shafts are connected by a…

Q: PROBLEM NO. 1 A 40-mm diameter, 533-mm length shaft is drilled, for a part of its length L₁, to a 20…

A: Given data: D=40 mmL=533 mmd1=20 mmd2=30 mmτ=80 MPaN=230 rpm Need to determine the maximum power…

Q: . Determine: the diameter of shaft

A: Given: P= 20 kW N=750 rpm T1/T2=2.5 WA=300 N WB=250 Nshear stress=70 MPa kt=2 km=1.5 DB=1000 mm…

Q: A standard 25-HP electric motor operates at 1800-RPM. If the motor is connected to a pump in the…

Q: neter of the shaft from stat = 5. Bending moment and tion speed of the shaft if ed in the…

A: In horizontal Plane: Now TorqueA= (500-75) × 82 = 1700 lb.in TA= TB (Power is…

Q: a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa,…

A: for solution refer below images.

Q: The drive shaft AB of an automobile is made of a steel having an allowable shear stress of Tallow =…

Q: Determine the minimum required diameter of the shaft CD.

Q: m. Design a cast Iron flange coupling for the shaft. The allowable stresses are Shear stress for the…

Q: (b)A pair of 14.5 degree full depth spur gears are used to transmit 20kW between shafts 40 cm apart…

A: Write the relation in diameters of gears. Dg+Dp2=400 mmDg+Dp=800 ...... (1) Again with linear…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

The motor shown supplies 126 hp at 1340 rpm at A. Shafts (1) and (2) are each solid 1.86-in.-diameter steel [G=11400 ksi] shafts with
lengths of L₁ = 79 in. and L₂=105 in., respectively. Assume Ng-27 teeth and N-42 teeth. The bearings shown permit free rotation of
the shafts.
(a) Determine the maximum shear stresses T₁, T2 produced in shafts (1) and (2).
(b) Determine the rotation angle D/A of gear D with respect to flange A.
Answers:
(a) T₁
=
(b) P DIA
Nc
WWAMACOM
Save for Later
C
9.3808
= i 2.1378
eTextbook and Media
NB
L₁
B
D
TD
ksi, 1₂:
=
i
14.5924
ksi.
Attempts: 1 of 5 used
Submit Answer

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Write the given data with suitable variables.

VIEW

Step 2: Calculation of torque on shaft 1 and shaft 2

VIEW

Step 3: Calculation of maximum shear stress in shaft 1 and 2

VIEW

Step 4: Calculation of rotation angle of gear D with respect to flange A

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 20 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A compound shaft drives several pulleys, as shown. Segments (1) and (2) of the compound shaft are hollow aluminum (G = 4000 ksi) shafts that have a polar moment of inertia of J = 2.835 in4. Segments (3) and (4) are solid steel (G = 12000 ksi) shafts that have polar moment inertia of J = 1.024 in4. The bearings shown allow the shaft to turn freely. Assume TB = 980 lb.ft TD= 525 lb.ft TE = 130lb.ft L1 =74in L2 =29in L3 =34in L4 =35in. Calculate the rotation angle (including the correct sign) of pulley E with respect to point A.
Please solve step by step both sub parts. shaft transmits 75 kW power at 300 r.p.m. The distance between the two bearing is 3000 mm. It is subjected to torsion only. Calculate the diameter of the shaft, (1)For steady loading and (ii) For suddenly applied load with minor shocks. Take the allowable shear stress for the shaft material as 35 N/mm².
Gear shaft ABCDE is subjected to the torques shown in the figure. Find the internal torque in each seg- ment, and then plot the torsional moment diagram. Assume that the spacing between gears is constant, i.e., 10 in. T1 = T2 = 1000 lb-in. 500 lb-in. A B T3 = 800 Ib-in. C Ta = 500 lb-in. d = 1.0 in. D T; = 800 lb-in. E
2-Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. (i) power tranmission = 230 kW(ii) speed = 80 rpm,(iii) Maximum shear stress = 60 MPa(iv) diameter ratio = 1.74(v) The maximum value of the twisting moment is 40% greater than its mean. (i) The mean torque is (Unit is in Nm)=__________ (ii) The maximum torque is (Unit is in Nm)=__________ (iii) The outer diameter of the shaft (unit in mm)=_______________ (iv) The inner diameter of the shaft (unit in mm)=_______________
Derive the equation of internal torques of section AB, i.e. torque for brass sleeve Tb and torque for steel shaft Ts in terms of T using the compatibility equation. [Note: Please include the matric number and corresponding Gs value.]
pair of 14.5 degree full depth spur gears are used to transmit 20kW between shafts 40 cm apart running at 1440 rp.m and 360 r.p.m respectively. The allowable stress and BHN are 600 MN/m, 160 and 550 MN/mm 140 respectively for the pinion and gear. Find the module, number ot teeth and face width. CheCk tor wear.
In a gear set, a 36-tooth spur pinion drives a 60-tooth spur gear. The teeth of these gear are cast iron profile. The diametral pitch is 6-teeth/in, the face width si 0.5 inches, and the pressure angle is 20 degrees. Assume that the pinion transmits 10 hp at a speed of 2000 rpm. Find the tangential load in lbf Find the contact stress in kpsi, assuming CP=1960 psi.
with diameter d = 38 mm transmits 37 kW to a gear Calculate the required speed of rotation (number of at B. The allowable shear stress in the steel is 40 MPa. X7-3 A motor driving a solid circular steel shaft revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit. Motor d = 38 mm B
Compute for the induced compressive stress in kPa, of a steel shafting of 59 mm diameter and 954 m in length that issubjected to an increase of temperature of 88ºC. Use 6.5x10-6/F, E = 30x106 psi.
The disc clutch of an automobile is carried on a 2-inch 6-splined shaft and not to slide under load. The nominal dimensions are as follows: b = 0.25 D; t = 0.075 D and d = 0.85 D. The hub length of 150 % of shaft diameter. Determine the total horsepower transmitted at 3,600 rpm, if the yield strength of the shaft is 1,400 psi
Design a square key for a 3 in diameter shaft to withstand a torque of 30000lb-in. The design stresses in shear and bearing can be safely taken as 11 ksi and 22 ksi, respectively. Find the length (inches) From Table AT 19, b=t=3/4 in
(8) An axle (non-rotating) is to be machined from AISI 1144, OQT 1,000°F, to the proportions keyway в shown, with a fillet radius r = 0.2D; F varies 1.SD from 400 lb. to 1,200 lb.; the supports are to the left of B, not shown. Let N = 2 (Soderberg Line). 6" (a) At the fillet, compute D and the 30 maximum tensile stress. (b) Compute D at section B. (c) Specify suitable dimensions. Keeping the given proportions, would a smaller diameter be permissible if the fillet were shot-peened?