The mobile crane (weight = 48 kN) shown in the figure moves across the bridge of length, / = 14 m. The front wheels of the mobile carry the three-quarter of its weight while the rear wheels carry a quarter of its weight. If the distance between front and rear wheel is b = 0.7 m. b A B Determine the position where the maximum bending moment occurs.

The mobile crane (weight = 48 kN) shown in the figure moves across the bridge of length, / = 14 m. The front wheels of the mobile carry the three-quarter of its weight while the rear wheels carry a quarter of its weight. If the distance between front and rear wheel is b = 0.7 m. b A B Determine the position where the maximum bending moment occurs.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2) A single axle load of P = 20 kN is to cross a simply supported beam made of four 50mm x 250mm fasten together as shown in the figure. Determine the safe diameter of the fasteners if the fasteners as spaced 100mm apart. The allowable shear stress in rivets is T = 145 MPa. 0 A P=20 kN 4m
solve correctly and show the complete solution.
Question Three The three-bar truss ABC shown in the figure part a has a span L = 3 m and is constructed of steel pipes having cross-sectional area A = 3900 mm² and modulus of elasticity E = 200 GPa. Identical loads P act both vertically and horizontally at joint C, as shown. (a) If P=475 kN, what is the horizontal displacement of joint B? (b) What is the maximum permissible load value Pmax if the displacement of joint B is limited to 1.5 mm? P A 45° 45° B L (a)
Q 3. A rigid beam AB is 5.5 m long, hinged at point A and supported by two pipes at C and D as shown in figure 3 below. Pipe 1 at C is of copper has a outer diameter of 120 mm and inner diameter of 100 mm and yield stress of copper is 138 N/mm² Pipe 2 at D is of steel has a outer diameter of 100 mm and inner diameter of 90 mm and yield stress of steel is 250 N/mm2 Calculate the safe load at A if the load factor is 1.66 Pipe 1 Pipe 2 Psafe 2.3 m 2 m C 5.5 m Angle ACE = 0 Figure 3 Angle BDF = 42° Take 0 = 10 Page 7 of 7 PTO
The 10-element truss system structure is loaded as shown in the figure. Determine the zero bars and the load values for each element. Indicate whether the elements are under tension or pressure. (A and B are fixed support)
I need the answer as soon as possible
A pin-jointed 2-D truss is loaded with a vertical load of 10 kN as shown in figure. The crosssectional area of the horizontal member is 150 mm² and cross-section areas of the members AC and BC are 200 mm² each. Modulus of elasticity of the truss material is 200 kN/mm². The magnitude of horizontal displacement (in mm, round off to two decimal places) of joint Cis A -6m 10 KN 5 m 4.5 m
9
Use x = 137 y = 37 a = 6 b = 8 c = 1
Find the maximum moment of the given load train at point n on the beam given in the figure?
Question Three The three-bar truss ABC shown in the figure part a has a span L = 3 m and is constructed of steel pipes having cross-sectional area A = 3900 mm² and modulus of elasticity E = 200 GPa. Identical loads P act both vertically and horizontally at joint C, as shown. (a) If P=475 kN, what is the horizontal displacement of joint B? (b) What is the maximum permissible load value Pmax if the displacement of joint B is limited to 1.5 mm? P P A 45° 45° B woobute L (a)
Structure analysis