The minimum steady, horizontal flight speed is less than 80 kts. At 295 kts the aircraft has about twice as much thrust available than req steady level flight. The power required is proportional to the velocity square. O At 300 kts the power available is nearly 78,000 hp.

The minimum steady, horizontal flight speed is less than 80 kts. At 295 kts the aircraft has about twice as much thrust available than req steady level flight. The power required is proportional to the velocity square. O At 300 kts the power available is nearly 78,000 hp.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

please dinot copy paste from other web i need urgent A petrol engine produces 250 kW while using 1.014 kg of fuel per minute. The fuel has a lower heating value of 45000 kJ/kg, and the engine has bore of 100 mm and the stroke-to-bore ratio of 1.2. The clearance volume of the cylinder is 1.178×105 mm3. The friction power is found to be 10% of the power that engine produces. Sketch (your own) the simple neat and clean block diagram of the engine, clearly indicating the control volume and control surface, with all the given data displayed on it. For air take the value of g = 1.4. Determine the following: The brake thermal efficiency (hb, th ). The indicated thermal efficiency (hind,th ). The mechanical efficiency (hmech ). The brake engine efficiency (hb ). The indicated engine efficiency (hind ). (Hint: Engine efficiency is a function of how the ideal work or power is calculated. Frequently, the air-standard cycle is used for calculating the theoretical work.) Use standard symbols…
True Story! The 1998-1999 Mars Climate Orbiter mission was declared a total loss in1999 as there was a unit conversion mismatch error between Lockheed Martin and NASA. Themismatch was in the thruster force units. NASA used the SI system which called forNewton-Seconds (4.45 times as large) of thrust and Lockheed Martin used Pound-Force Seconds.Calculations placed the Orbiter at 68 miles from the surface as it went into orbit, but it waswithin 57 km of the surface after the breaking maneuver. Any distance from the surface lessthan 50 miles would have caused the Orbiter to crash.a. What was the actual distance of the Orbiter from the surface in miles?b. In percentage, how far off from the calculated 68 miles was the Orbiter?
Please use the following equations as appropriate. L = ½ pv²SC₁ p = 21/v²SC, v²= 2L/PSC S=21/pv³C, Lift = Weight Given the following: Wingspan Avg Chord Altitude Airspeed 40 ft. 5 % ft. 10,000 ft. 140 m/h 10° a Flaps What is the weight of this aircraft in equilibrium flight? Retracted
Aircraft B Gross weight 1,600 lb Wing Area 250 ft Maximum thrust 0.011 DO K 0.022 1.45 max Mdr NB 1 mph = 5,280 ft/3,600s = 1 4667 ft/s Aircraft B is a sailplane. Find the maximum-endurance performance and conditions (velocity, glide angle. rate of descent) at 30,000 ft. And calculate the distance (miles) and time (hour) taken to reach sea level under these conditions
Scores
The maximum lift-to-drag ratio of a 600,000 lb aircraft is 18.7. The Thrust Specific Fuel Consumption (TSFC) = 0.85 (lbs/hr)/lb. The total fuel on board is Wf = 180,000 lbs. Find the maximum endurance of the aircraft in hours. Round off your answer in ones place. Answer for a thumbs up
HANDWRITTEN AND FINAL ANSWER MUST BE IN ENGLISH UNITS. Show solution. An experimental gas turbine engine is under development to increase its mechanical efficiency. It has a turbine efficiency of 95% and compressor efficiency of 85%. The following parameters are provided: P1 = 550 kPa, T1 = 25 deg C, rp = 5.5, T3 = 1450 deg C, Wnet = 5500 kW. Compute for the (a) flow rate and (b) mean effective pressure. Consider Ethane as your working fluid.
LR = 5m, LG = 2.5m and LC = 1.1m Q2. The Skylark family of sounding rockets consisted of a number of variants (denoted Skylark 5, Skylark 7, and Skylark 12 respectively). These are illustrated on Page 3. The data given below is based on that for the rocket motors they used (all manufactured and named by what was Royal Ordinance – now part of Roxel): Raven XI Motor Total mass: 1280 kg Length = LR See Case Table (units are m) Diameter = 0.44 m Goldfinch IIA Motor Total mass: 420 kg Length = LG See Case Table (units are m) Diameter = 0.44 m Cuckoo IV Motor Total mass: 242 kg Length = LC See Case Table (units are m) Diameter = 0.44 m The payload mass which is additional to the motor masses is to be taken as 100 kg. (a) For the configurations of the three rockets shown on Page 3 in Fig. Q2: (i) Determine the Pitching/Yawing moment of inertia of each rocket about the base of each rocket. (ii) Explain how you could then find the the Pitching/Yawing moment of inertia of each rocket about its…
I need a clear answer by hand, not by keyboard | dybala Suppose that a certain fraction of the power produced by a 350 MW coal plant is offset by wind power. Assume that when the coal plant runs at its constant rated power it has an efficiency of 37%, but that when it needs to be ramped up and down to compensate for the wind power variations its efficiency is reduced by according to e=0.37 -0.00001p², at what p the efficiency is maximum? Signature Head of Department
MA-MB Clear my choice Suppose the coefficient of static and kinetic friction between the road and the tires on a car is 0.60 and 0.30 respectively. The car has no negative lift force. What is the maximum possible speed (in m/s) of the car without slipping as it rounds a flat curve of 27 m radius? Note: write your answer with one decimal place. Answer: Finish attempt . PHYSZJO1 apevissac sall/u e here to search Lr Lrc Ps HUAWEI
The sports car has a mass of 2.5 Mg and accelerates at 6 m/s², starting from rest. (Figure 1) Figure 86°F Clear 21 1 of 1
Suppose we got the following data during a test of a 2- stroke engine in which gas is usedas a fuel:Diameter of the piston = 149 mmStroke length = 179 mmClearance volume = 0.88 literrpm of the engine = 302Indicated mean effective pressure = 6.0 barGas consumption = 6.0 m3/hCalorific value of the gas (fuel) = 16990 kJ/m3Make a clear sketch the geometry of this engine using the data and determine thefollowing:i. Indicated power developed by the engine in watt.ii. Air Standard Efficiencyiii. Indicated thermal efficiency of the engine.