Answered: The maximum slope of a ground for which…

The maximum slope of a ground for which the error due to slope is limited to 1 in 800 can be expressed in gradient as 1 in. (round off to nearest integer).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Summative Assessment - Virtual Work Method Determine Determine the Slope at C. Use the Virtual Work…

A: Given values: Consider the given beam. E = 29000 ksi I = 200 in4 = 0.0096 ft4 Using Virtual work…

Q: The observed interior angles of a triangle are A = 35°14'37", B = 96° 30' 09", and C= 48°15'05".…

Q: Calculate the horizontal displacement and the slope at C. 10x10 cm? |C 2 KN E = 200 GPa 10x20 cm B…

A: The virtual work method is also known as the unit load method. In this method, the deflection of a…

Q: Your team want to measure line AB but there is an obstruction on line. You set up two lines AC and…

A: To find length of line AB,BD,AD

Q: From a transit line to the edge of a river a series of perpendicular offsets are taken. These…

A: To Find Area 1. Using trapezoidal rule 2. Simpson's one third rule

Q: Determine the slope at A and displacement at C. El is constant. 5 kN-m B C -1.5 m. −1.5 m

Q: For a rock slope shown in figure belows, consider the following: i-55°, p-40.6-40. 0A-38° and…

Q: Using Area Moment Method (AMM), Calculate the deviation of point B when a tangent line is drawn at…

Q: PROBLEM 2: Find the required slope of the channel bottom when water flowing at the rate of 5.82…

Q: settlement of PL^3/24ei at a

A: Given that, Settlement atA=PL324EI. The objective is to determine the SFD and BMD.

Q: am shown, use double integration method to slope at "B" ite steps) 201 EI = Constant EI dy = ±EI

Q: Question/ Calculate Young's modulus (Y) using the following formula: 1672M 1 Y= bd3 slope For your…

A: Mass M=100gm Width =2cm Thickness=0.25cm

Q: Fundamentals of Surveying: Please show your solution. A line with bearing, S 9° 45' W intersects…

Q: difference in elevation of points A and B is G meters. Solve for the approximated correction due to…

Q: A right circular cone of slant height 10 in. has a radius of 4 in. Find the angle of the sector of a…

A: Given values: Right circular cone Slant Height =10 in. Radius= 4 in. Circle of Radius = 10 in. Area…

Q: Define Coefficient of Lateral Earth Pressure at Rest

A: Earth pressure: Th force is acting on the retaining wall when the soil is under the sloping…

Q: From the continuous beam show, determine the Slope at Bin kNm /El. El is constant. 20 kN 15 kN/m D A…

A: here support A &D is fixed support and B & C is roller support hence only degree of…

Q: 30 kN 50 kN B C D 1m 3 m 2 m Figure P-403

A: We have to solve the above given beam using integration method with slope intercept as per the solid…

Q: Problem 2)y "For the beam loaded as shown below, by the area-moment theorems, (AMM or AMT),…

Q: Fundamentals of Surveying: Please show your solution. 7.) A line with bearing, N 77° 45' E…

Q: On an inclined plane, the difference in elevation of points A and B is 7 meters. Solve for the…

Q: 35kN/m 180 kN 15 kN/m -5 m- -5 m- 4 m El = constant E = 70 GPa I = 2,340 (10°) mm %3D

A: Reactions in Real Beam: ∑V=0RA+RC=180+87.5+60=327.5∑MD=015×4×12+12×35×5×8.33+180×5-RC×10=0⇒RC=234.89…

Q: 12. Slope distances AB and BC measures 330.49 m and 660.97 m, respectively. The differences in…

Q: Slope distance AB measures 550.65 m and the difference in elevation is 170.24 m for points A and B.…

Q: PROBLEM 1 Solve the slope and deflection at points A and B using the Moment-Area Method. Point B is…

A: Given data: EI=200×106×7.5×10-6EI=1500 kN.m2

Q: HW: It is required to measure distance from C to point B (cross the river) see the presented figure.…

A: Given:CH = CG = 2m, GH = 2.3m, AE = 2.5m, AD = 2m, ED = 3.34m, CA 35m,Required:Angle C and ADistance…

Q: (Trilateration): In a trilateration network one of the triangles has the following data: AB = 600m,…

Q: Using Method of Virtual work, determine the slope at point A. Use E = 200GP and I= 100x10 mm Use…

Q: A railway embankment 400 m long is 12 m wide at the formation level. The side slope of the…

A: Given-A railway embankment 4000m long with side slope of 2:1. The formation level at station zero is…

Q: B. Find station and elevation of highest point using EQUATION OF THE PARABOLA. GIVEN: G1 = +4.5 %…

Q: A student used the breaking tape method in determining the horizontal distance of a sloping terrain…

Q: Given the following data in a sample D = 5°, Sta PC = 1+234.56. Azimuth of the back and forward…

Q: 3) Use the virtual work method to determine the horizontal deflection at joint E and slope at joint…

Question

The maximum slope of a ground for which the error due to slope is limited
to 1 in 800 can be expressed in gradient as 1 in.
(round off to nearest integer).

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Slope calculation

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the slope at point D using conjugate beam method. 75 k Hinge 40 k 250 k-ft E A B C D E12 ft 12 ft 12 ft- -12 ft El = constant E = 29,000 ksi I= 6,000 in.4 %3D
The body on the 30° incline is acted upon by a force P inclined at 20° with the horizontal. If P is resolved into components parallel and perpendicular to incline and the value of the parallel component is 1800 N, compute the value of the perpendicular component. A)2145.16 N B)2416.45 N C)2415.16 N D)2453.17 N
3. USING DOUBLE INTEGRATION METHOD (DIM), DETERMINE THE SLOPE AND DEFLECTION AT POINT C. CONSIDER EI AS CONSTANT AND START X FROM A 10 kN 25 kN/m A 1.25 B 2.5m C√ 2.5m VD
detailed solution pls.
4. If the scaled horizontal distance between points A and b is 433.50m and the elevation of A and B are 385m nd 310m, respectively, determine the average slope between the two points in: a. mils b. percent c. gradient d. grads e. Degrees
Calculate the factor of safety in terms of slope stability using the Cousin's Chart method of the soil, the information of which is given below
determine the slope and displacement at point C. Use the method of virtual work E = 29x10^3 ksi I = 800 in^4
Using Area Moment Method (AMM), Calculate the change in slope between tangent lines drawn at points A and C, i.e. BAc in terms of EI? 75 KN A В 2 m 3 m
A house with 932 kN weight is built on a steep slope defined by points A, B, and C. To help assess the possibility of slope failure (mud slide), determine the components of the weight in directions normal (perpendicular) to the slope. The rectangular form of the weight and the component of the weight perpendicular to the slope defined by the points A, B, and C.
Show FBD