The maximum flux density is the core of a 3000/240-V; 50Hz single phase distribution transformer is 1.25 Tesla. If the voltage induced per turn is 8 volts, determine the cross sectional of the core in cm2

The maximum flux density is the core of a 3000/240-V; 50Hz single phase distribution transformer is 1.25 Tesla. If the voltage induced per turn is 8 volts, determine the cross sectional of the core in cm2

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.9MCQ: Match the following: (i) Hysteresis loss (a) Can be redud by constructing the core with laminated...

See similar textbooks

Related questions

Q: 5. Determine the value of the IR, ly and Is currents in the circuit shown in the figure using a mesh...

Q: Q6 A 250 V shunt motor on no-load runs at 1000 r.p.m. and takes 5 A. the total armature and shunt fi...

A: Note: We are authorized to answer the first question since the exact one wasn’t specified. Please su...

Q: When 120 V, 60 Hz is applied to the primary winding of a transformer, the core loss is 240 W. When 5...

Q: :Digital Communication Three different information signals each bandlimited to 6kHz, 11kHz, and 3kHz...

A: Given f1 = 6kHz f2 = 11kHZ f3 = 3kHz L = 256

Q: Theoretical calculations: 3. How dose the bandwidth change in relation to increasing signal amplitud...

Q: Q1). If the switch number 1 is closed and 2 is open what voltage would you measure at : i). V1 ii)....

Q: Plot the forward and reversed zener current and zener voltage based on the measured values from Tabl...

A: The given tables are shown below:

Q: Determine the TheVinin Voltage at a/b. 53 "jbs rem me t Ta 10*90°V 5%0°A o b

A: When two mutually coupled inductor L1 ,L2 are connected in series with mutual inductor M then depen...

Q: 4700R1 V ( 2V, at 10 kHz. 10 mH 3L1 10Ω R3 Calculate the peak current voltage across R1 phase angle ...

Q: the largest overload heater is ____ amperes.

A: Overload heaters are also known as Overload Relay Heater. There are four different classes of heater...

Q: n impedance coil has a resistance 0 A from 220V, 60 Hz mains. What i e condenser connected in parall...

Q: What is the voltage across the resistor

Q: 4. R,=_2 R, = 1.6 kn R2 =1.2 k R3 1 kn

Q: -) For LTI System has an n-1 impulse responce of ()" ucn) Find the output responce for he input ()" ...

Q: Graph: Take a graph sheet and divide it into 4 equal parts. Mark origin at the center of the graph ...

A: According to the question, for the given data as shown below We need to plot the V-I characteristic...

Q: determine the current I

Q: A 3-phase 5KV (L-L), 8-pole, 60Hz, squirrel-cage induction motor draws a current of 400A and total a...

Q: Tutorial Problems No. 1 Q1 A250 v shunt motor takes a total current of 20 A. the shunt field and arm...

Q: Derive the efficiency of a class ab power wheras it is in the range of 50%-78.5%

Q: A coaxial cable's shiled diameter is 0.4cm and the inner conductor has a diameter of 0.02cm. What is...

A: STEPS: First find the L and C of the cable using Inner and outer diameter Characteristics impedance...

Q: Sag of the conductors of a transmission line is 2 m when the span is 200 m. Now if the height of the...

A: The vertically difference in level across points of support (most typically transmission poles) and ...

Q: 2. What should be the value of R, for maximum power transfer? Find the maximum power. 2Vx 100V RL 42...

Q: What's the de 011100

Q: Why is the power factor of an induction motor calculated at full load/blocked rotor test?

A: Blocked Rotor Test A small voltage applied across the phase Full load current flow through the arm...

Q: Problem 1 From the given circuit, determine the following: a. The voltage across the resistor R and ...

A: In this question, We need to calculate the voltage across the resistance Rx and power in it? Curre...

Q: what are designed to protect the motor from an overload condition

A: Overload motor: A motor is connected with excessive load, draws more current, and produces insuffic...

Q: Let's Try (Evaluation) Directions: Identify each circuit whether they are properly assembled or not....

Q: Consider the Circuit shown below: Rf Ri Vin Vo Solve for the voltage gain in dB if Rf-11.77kOhms and...

Q: A balanced three-phase source with a 208 V rms (line-line) is delivering power to a balanced Y-conne...

A: The solution is given below

Q: Given that full load copper losses are exactly twice the iron losses in a 50 kVA transformer, and th...

A: In this question we have given quarter load efficiency of a single phase transformer ..We have to fi...

Q: 3: Find all the second-order partial derivatives of the functions a) f(x, y) = x + y + xy

A: The solution is given below .

Q: i1. Find VAB for the given circuit below in Figure lc. +20 V • 100 150 20 202 A B Figure lc

Q: Three non-inductive resistances, each of 100 ohms are connected in star to 3 phase, 440 V supply. Th...

Q: Q2.Find the total resistance of the series resistors in Fig.2 Again, recognize 3.3 k as a standard v...

Q: Table 4.1 1. 2. 3 4. 6. 7. 10 Vz (V) V (V) z (mA) 2010 0.003. O61.2 8e 0.4u131 235 3.3 4.33

Q: 3 ww www RI R3 Ez- 10 V R2 Fig. 3

A: Note: It is not given the value of resistance R1, R2 and R3 so am assuming 10 ohm. Circuit is give...

Q: Example: A 3-ø transmission line 250 km long has the following constants: Resistance/phase/km = 0-16...

Q: Electrical Engineering Question

A: Given a single phase half wave rectifier with ac supply is given to load resistor through a thyristo...

Q: Voltmeter Readings of Different Hypothetical Metals 2nd reading, Metal 1st 3rd Average Standard (hyp...

A: For calculation of standard deviation ,first we have to calculate variance.once we know the variance...

Q: 5: Evaluate dw/ dt at the given value of t, by using the Chain Rule and by expressing w in terms of ...

A: Chain rule differential is very important to analyze the electric and magnetic field in three dimens...

Q: ) A 500 kVA single-phase transformer A with percentage impedance of 0.010 + j0.05 is connected in pa...

Q: Selve tie chfferstiat egartier by luplace troms f リーフ=シツ)=!, fio) =t 24 Sulve ジナジ+7ソ=e 9(0) = 0-16, ...

Q: The following data are given for two branch parallel circuit, E = 125 V, XL = 150, Xc = 25 0, Rc = 1...

A: Given

Q: b.) For the network shown below: a. Determine Zi and Zo b. Find Av c. Repeat parts (a) and (b) with ...

A: We need to find out input, output impedance and gain for given circuit

Q: The load in each branch of a delta-connected balanced 3 phase circuit consist of an inductance of 0....

Q: 3) Determine the minimum transmission bandwidth required to transmit the following signals: 9,(t) 20...

Q: QU For an LT I System described by yn)=8ycn-1) –12 y(n-2)+2X(n)–4 x(n-1) Determine Fhe unit step res...

A: Steps: As the system is Liner time-invariant, change the value of n to find the y(n) substitute n=0...

Q: Design 8-bit adder/subtractor with overflow checker 1- desing from Full adder. 2- design from 4-bit ...

A: Logic gates are basic elements of every computational circuits. The Adder/subtractor circuits are al...

Q: Find the TF of the following diagram: C2 C, R4 ww R2 -ww R3 E{s) E(s) E(s)

Q: f (a,b.c,d) d) = 11M(0,1,6,8, 11, 12) · I|D(3,7,14, 15)

Question

The maximum flux density is the core of a 3000/240-V; 50Hz single phase distribution
transformer is 1.25 Tesla. If the voltage induced per turn is 8 volts, determine the cross
sectional of the core in cm2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Match the following: (i) Hysteresis loss (a) Can be redud by constructing the core with laminated sheets of alloy steel (ii) Eddy current loss (b) Can be reduced by the use of special high grades of alloy stl as core material.
The core of a transformer operating at 50 Hz has an eddy current loss of 100 W/m3 and the corelaminations have a thickness of 0.50 mm. The core is redesigned so as to operate with the same eddycurrent loss but at a different voltage and at a frequency of 250 Hz. Assuming that at the new voltage themaximum flux density is one-third of its original value and the resistivity of the core remains unaltered,determine the necessary new thickness of the laminations. Clear and detailed solution.
The path of a magnetic flux in a transformer should have O High resistance O Low reluctance O Low resistance O High reluctance
The maximum flux density in the core of a 250/3000V, 50Hz single phasetransformer is 1.2 Wb/m2. If the emf per turn is 8 volt, determinea) Area of the core
The function of Copper shading band in induction type energy meter is to ensure flux produced by potential coil is exactly in quadrature with supply voltage. Select one: O True False
A ferromagnetic core is shown in Figure PI-2. The depth of the core is 5 cm. The other dimensions of the core are as shown in the figure. Find the value of the current that will produce a flux of 0.005 Wb. With this current, what is the flux density at the top of the core? What is the flux density at the right side of the core? Assume that the relative permeability of the core is 1000. -10 cm- - 20 cm- 15 cm 400 turns 15 cm 15 cm Core depth 5 cm
9. What are the different types of core?
A transformer has primary and secondary turns of 1250 and 125 respectively. It has core cross-sectionof 36 cm2 and its rms flux density is to be limited to 1.4 T (to prevent core saturation). Whatmaximum 50 Hz voltage can be applied on the primary side and the corresponding open-circuitsecondary voltage?The core has a mean length of 150 cm and its relative permeability can be assumed to be 8000. Whatwould be the rms exciting current when the transformer’s primary winding is excited at a voltage ascalculated above? Also calculate the magnetizing susceptance as seen from primary and secondarysides.If the transformer were to be excited at 60 Hz, 1. What should be the maximum primary voltage for thecore flux density limit not to be exceeded? 2. What would be the magnetizing susceptance as seen oneach side in this case?
In a certain cast-steel core series magnetic circuit with a 400 turns, 170 At/m, mean length of 0.16 m and 0. 002 square meters cross-sectional area. the value of current to develop a 0.0004 Wb is
In transformer, the eddy current loss can be minimized by O using thin size copper conductors O using magnetic material with low permeability laminating the core O using magnetic material with high permeability
Question: 01 A two-legged core is shown in figure below. The winding on the left leg of the core (N) has 800 turns. The depth of the core is 15 cm. The small airgap is 0.05 cm and there is no fringing effect. If the dimensions are as shown, then determine the total reluctance of the given core when u, =800 and constant. 15cm 25cm 10cm 10cm 50cm N=800 5cm
(a) Explain briefly what is fringing effect and leakage flux. (b) A ferromagnetic core is shown in Figure 1. The depth of the core is 10 cm. The other dimensions of the core are as shown in the figure. By assuming the magnetic leakage to be negligible and relative permeability of the core is 800. Calculate the total reluctance and find the value of the current that will produce a flux of 0.01 Wb. With this current, calculate the flux density at the top of the core 20 cm 40 cm 10 cm, 30 cm 500 turns 30 cm 30 cm Figure 1