The maraging steel is expected to withstand an applied force of 50 tones. To assure asufficient safety, the maximum allowable stress on the rod is limited to 150 kg/mm2. Therod must be at least 1000 mm long but must deform elastically when the force is applied.Design an appropriate rod.

Q: Calculate to the correct number of significant figures. (3.14x2.4367) - 2.34

A: The problem is given as, In this, it can be seen that the minimum significant figure of the number…

Q: 5. Work-energy principle to be useful in determining the change in the speed of a particle during a…

A: Work energy principle to be useful in determining the change in the speed of a particle during  a…

Q: i cant read this.. can you write it out??

A:

Q: Q1: Find the resultant force and the component force F for the system shown below (fig 1) using…

A: Calculated the resultant force and the component of force F for the system using parallelogram law.

Q: solve both

A: Power input, Gear speed of input shaft, Gear ratio, Power loss,

Q: Forces and moments are scalar Forces are moments are vector quantities.

A: Forces and moments are both physical quantities that can be used to describe the behavior of objects…

Q: 3

A:

Q: 7 Doorbe Daanbe the proccdoe lor cvalvahon crnd Cncl improement f laaul. ?

A: Systematic Layout Planning Procedure:- It is a procedure layout design approach developed by Muther…

Q: Create a free hand isometric drawing of the three objects

A: Free hand isometric drawing of all three components are drawn below...

Q: ww

A: ***As per our company policy we are supposed to do only 1 question if you need the rest please…

Q: How did you get theta =45?

A: Consider following given figure of a structure.here we need to determine the angle between member DE…

Q: What does shear strains cause?

A: Answer Shear Strain : it is the angular displacement from the original position

Q: Given the points A( – 5, 6, – 4), B( – 2, — 10, 6), and C(4, 0, 5), find (a) the angle between AB →…

A:

Q: where is the T-S diagram

A: Rankine Cycle is a ideal cycle for producing net work output in thermal power plant where water is a…

Q: What are the different types of force? Applied Tension Gravitational Spring Air Resistance Normal…

A: (I) Force has been classified on the basis of contact which is as follow 1. Contact force:- These…

Q: Name the following figures.

A: Pneumatic Cylinder Pivot Bracket with rigid bearing AB7

Q: ove that the calculated values ne graphical method and the ematical analysis method the same, for…

A:

Q: e b a What is the degree of freedom of the mechanism? а. 3 O b. 0 Ос. 1 d. 4 е. 2

A: Degree of freedom is given by the following relation, F=3(l-1)-2j-h Where l=no.of link=4 j=no.of…

Q: In a hydraulic press machine the diameters of the effort and load pistons are respectively 25 cm and…

A:

Q: How can I calculate the force tho

A: The stress is defined as the resisting force per unit area. here, σAl=12800 psiσsteel=18850…

Q: In a lathe machine tool, when the cutting tool moves parallel to the axis of rotation of the…

A: It is required to justify given statement

Q: can you Reslove?

A: To solve the problem you have typed in, follow these steps: Analyze the given data:L2 = 6Q2 = 35…

Q: Solve for the mobility. Show your logical and accurate solutions after every fig

A:

Q: Q1 The 45° strain rosette is mounted on a surface of the bracket as shown in Figure Q1. The bracket…

A:

Q: What is the answer in #3B. Show complete solution and FBD

A:

Q: From the projected views obtain the isometric drawing.

A: According to the details provided in the question, there are three views of the first angle of…

Q: A line in a drawing is 3 inches long, when measured.  If the drawing scale is 20:1, how long is that…

A: Given Data The length of line is:3 inches The drawing scale is:20:1 To find: The actual length of…

Q: Please give the details explanation of the answer

A:

Q: 583 mK/s = ________ μK/ms 2. 583 mK/s = _______ K/s

A: Given data 1. 583 mK/s = ________ μK/ms 2. 583 mK/s = _______ K/s

Q: please, i need to see how did you get to this formula

A: ◆ The purpose of using this formula is to avoid complex calculation and to get the answer in minimum…

Q: The name of this machincal drawing

A: Given Data : Mechanical drawing

Q: A Tyrannosaurus named Rex was having a birthday. He was standing on one end of a cart that rolled…

A:

Q: What is the Falling Block?

A: Falling block: The falling block is an action in which a solid metal slides vertically in a grove…

Q: Q3/ For the plate shown in figure below find * (a) ΣΑ YA 7 9. X 8 5

A:

Q: (5) In order to forge a pure gold ring, you first need to purchase the gold. The ring design is a…

A: According to Pappus–Guldinus theorem volume can be given as V=Ax2π×yArea of the block as per given…

Q: Which of the following statement is correct in terms of degree of freedom? Select one: O Moving left…

A:

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.