The manometer pictured has been filled with 2 different fluids and is open to the atmosphere on both sides. If fluid 1 has a density of 1g/cm3, the approximate density of fluid 2 is: Fluid 1 Fluid 2

Q: What are fluidised or moving-bed adsorbers?

A: Adsorption is a separation process in which the solute from the fluid is separated by adsorbing on…

Q: The reason for adding ink with water in manometer is O a. improve aesthetics O b. improve mass O c.…

A: Reason for adding ink to water in the manometer is asked.

Q: What conditions cause the pinch point to migrate away from the feed location?

A: Distillation is a vapor-liquid separation process. Distillation is the separating technique which is…

Q: How about the relative error and percentage error of the volume?

A:

Q: Regarding amorphous plastics, explain why they tend to have higher tensile strength when deformed…

A: Amorphous plastics have no specific order and pattern in their molecular structure. Thus, the…

Q: Describe the effect bend testing have on the mechanical properties of silicon nitride.

A: Effect of bend testing on the mechanical properties of silicon nitride is to be explained.

Q: Is pinch point always located at the feed stage?

A: The location of the pinch point is to be mentioned.

Q: Describe the Impressed Current System of Cathodic protection

A: Metals are always subjected to corrosion damage. corrosion occurs when most or all the atoms on the…

Q: What is tensile test

A: The definition of the tensile test is to be mentioned.

Q: crystallization mechanism,

A: Crystallization is a process in which mass transfer of solute takes place from the liquid solution…

Q: Calculate the volume of an HCP unit cell in terms of cell edge (a) and height (c).

A:

Q: 6.) Calculate the paint thickness if 2 gallons of paint covers a wall 10 feet high by 30 feet long.…

A: Given: Amount of paint = 2 gallons = 0.00757082 m3            Area of wall = 300 ft2 = 27.8709 m2…

Q: Describe five main parameters that govern the performance of the polymer production process. Provide…

A: Polymer manufacture is a complex process governed by numerous aspects that affect the final…

Q: Describe 1st angle and 3rd angle Projections?

A: 1. First Angle Projection : In the first angle projection, we can placed the object in the 1st…

Q: Specific gravity (SG) for calcium carbide

A:

Q: In the plate and frame filter press, by plotting the filtrate volume as a function of time per…

A:

Q: What is a  vane-axial cyclone seperator?

A: This question is from cyclone separators which form an important part in separation processes. The…

Q: 1. Explain in detail how grain size affects the strength of a metal alloy.

A: The grain size of a metal alloy significantly affects its strength due to the influence of grain…

Q: Process flow scheme on how to make tempered glass

A: There are two types of commercial glass based on the process of their manufacture. These are:…

Q: In barrel plating, why is the barrel containing the small parts rotated?

A: The reason for rotation of the small parts of the barrel in barrel plating is to be mentioned.

Q: How is oil formed in the ground?

A: There are two theories for the origin and formation of oil. Consider my following slides for a…

Q: When the instantaneous load is applied perpendicular to the specimen cross section, the material is…

A:

Q: C; Draw the temperature distribution long the insulated tip fin.

A: Fins are used in heat transfer to increase the surface area of a heat exchanger, thereby increasing…

Q: Calculate the porosity of the core

A: Given data: The density of the oil = 0.85 g/cc Weight of dry sample in air = 42.4 g Weight of the…

Q: Why is it important to determine the moisture content before it enters the mill

A: Introduction Milling is a term used to refer to mechanical techniques to reduce the particle-size of…

Q: What is a pinch point or region?

A: The definition of the pinch point is to be mentioned.

Q: could you touch further on the last slide, where does the mixing point come from and also tie lines…

A: Since there are three different components, So simple distillation cannot be done to separate themA…

Q: When we change the fluid package from one package to another, does the temperature and pressure…

A: When we change the fluid package from one another then the following properties will change such…

Q: What are the advantages of the espresso machine over the drip method?

A: The advantages of the espresso machine in comparison to the drip method are to be mentioned.

Q: List out various tests for the measurement of workability and explain any 2 in detail.

A: The objective of the question is to list out the various tests used for measuring workability in…

Q: How to calculate pressure drop in Gas pipe , formula ,

A: When gas flows in pipes, the pressure drop is caused due to following reasons:Friction in the…

Q: 3 Ways to separate pebbles and water and its step by step process

A: The three methods that can be used to separate water and pebbles are as follows: 1) Pour the mixture…

Q: How is a large surface area achieved for adsorption?

A: The technique by which surface area in large amount is obtained for the adsorption process is to be…

Q: The following are not commonly made from composites: Select one: a. Desks b. Canoes c. Bridges d.…

A: Ans.  Composites is the material that are made up of two or more materials. Which on combining they…

Q: Describe the factors that affect fluidization.

A: Factor that have an effect on fluidization are  fluidization parameter (calculated through inlet air…