The machine is commenced to be heated at some point of a quasi-equilibrium manner till the temperature of air reaches to 900 K. During the manner the stress within the cylinder is held constant. Initially, 1kg air at 600K and at 150 kPa is contained in a piston - cylinder device. Air may be assumed as Ideal Gas below those conditions. a) Calculate the heat supplied to the air within the cylinder at some point of this process. b) Sketch the P[kPal-V[m³] diagram of the process. Indicate the path of the process. No want to explicit the extent of the air at the diagram. Please do best a difficult sketch.

The machine is commenced to be heated at some point of a quasi-equilibrium manner till the temperature of air reaches to 900 K. During the manner the stress within the cylinder is held constant. Initially, 1kg air at 600K and at 150 kPa is contained in a piston - cylinder device. Air may be assumed as Ideal Gas below those conditions. a) Calculate the heat supplied to the air within the cylinder at some point of this process. b) Sketch the P[kPal-V[m³] diagram of the process. Indicate the path of the process. No want to explicit the extent of the air at the diagram. Please do best a difficult sketch.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A rigid vessel of 0.5 m3 volume containing saturated steam at 109°C, how much heat must be removed to bring its temperature to 25°C. *
Q1: 100kg of Sausage 'Frankfurter' is to be cooled from 25°C to -5°C. Using the energy content (enthalpy), determine the amount of heat that must be removed from the Sausage?
Thermodynamics subject. Pleas show the complete and step by step solution. . A certain gas at 101.325kPa and 160C whose volume is 2.83m3 are compressed into a storage vessel of 0.31m3 capacity. Before admission, the storage vessel contained the gas at 137.8kPa and 240 C; after admission the pressure has increased to 1171.8kPa. What should be the final temperature of the gas in the vessel in Rankine?
3-28 Complete this table for H₂O. T, °C 140 80 P, kPa 200 950 500 800 h, kJ/kg 1800 3162.2 X 0.7 0.0 Phase description
Consider a cylinder/piston system containing 2 kg of ammonia as saturated vapor at 20°C is cooled isothermally till its volume is half the initial volume. a. List assumptions to solve problem b. Find pressure, temperature and specific volume after the cooling process? c. Show process on T-v and P-v diagrams showing all phases and equilibrium curves
NOTE: Complete solution and show the derivation/cancellation of units. A steel flask of 0.04 m capacity is used to store Nitrogen at 120 bar and 20°C. The flask is protected against excessive pressure by a fusible plug which will melt and allow the gas to escape if the temperature is too high. A. How many kilogram of Nitrogen will the flask hold at the design conditions? B. At what temperature in °C must fusible plug melt in order to limit the pressure of flask to a maximum of 150 bar?
2) Two glass bulbs, one on the left with a volume of 2 liters and the other on the right with avolume of 6 liters, are connected to one another by a thin tube that is initially closed by astopcock. The bulb on the left has 0.1 moles of ideal gas, and the bulb on the right isevacuated. The system is in thermal equilibrium with the surroundings at 300K. When thestopcock is opened, the gas flows out to fill both bulbs. Calculate A for this process. If wewere to insert a propeller to extract work as the gas flows from left to right, what is themaximum amount of work that we could possibly extract?
c) ofR-134a at an initial pressure of 1.2 MPa is filled in a rigid container with a volume of 24.228 m³. The container is then cooled to 40°C. i. Determine the initial temperature and final pressure of the R-134a. Clearly show all calculations. Ikg ii. Show the process on a properly labelled pressure versus specific volume (P-v) diagram with respect to saturation lines.
Q1) A 10-L rigid tank contains R-22 at -10°C, 80% quality. A 10-A electric current (from a 6-V battery) is passed through a resistor inside the tank for 10 min, after which the R-22 temperature is 40°C. What was the heat transfer to or from the tank during this process? [-23.5 kJ]