The liquid is flowing separately through each of two pipes whose diameters are in the ratio of 2:1, if the ratio of the velocities of flow in the two pipes by 1: 2, then the ratio of the amounts of the liquid flowing per sec through the pipe will be 1.2:1 2.1:1 3.4:1 4.1:8 fluid-mechanics fluid-kinematics

The liquid is flowing separately through each of two pipes whose diameters are in the ratio of 2:1, if the ratio of the velocities of flow in the two pipes by 1: 2, then the ratio of the amounts of the liquid flowing per sec through the pipe will be 1.2:1 2.1:1 3.4:1 4.1:8 fluid-mechanics fluid-kinematics

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

subject: fluid mechanics course: civil engineering
can you help me with part d) please
question 4
In figure 2.5, if the pressure of gas in bulb A is 50 cm Hg vacuum and Patm = 76 cm Hg, the height of column H is equal to Patm H 424 Hg:
A closed pressurized tank shown below is filled with oil and mercury. Mercury is confined in an internal reservoir inside the closed tank, the height of mercury is 450mm. An open manometer is placed on the bottom left part of the tank with liquid “X” as its gage liquid , the deflection from the gage liquid shows 800mm. Determine the following:a) Height of the oil from point A up to point c if height A to C is 5 times the height of y. b) Pressure @ point B in kPa. c) Pressure @ point C in psi.
e 10
Consider oil flowing through a horizontal pipe at a rate of 3 liter/s. There are two sections of the pipe with diameters 10 cm and 7 cm and the two sections are connected by a smooth reducing section as shown in the schematic. We use a manometer with glycerin as the manometer fluid (with glycerin density of Pglycerin 1,260 kg/m³) to measure the pressure difference between the two pipe sections. Assume that frictional effects are negligible and consider specific gravity of oil as SGoil = 0.76. What is the manometer reading, h (i.e. differential height of glycerin between the two arms of the manometer)? 10 cm I h T 7 cm-
Need help! Image attached. A regulation tennis ball is made of an elastic material and can be modeled as a sphere. The center of the tennis ball is hollow, filled with pressurized air. You may assume the mass of air inside the tennis ball is negligible. The elastic portion of the tennis ball has a mass of 58 grams [g]. The outer diameter is 2.6 inches (in] and elastic material has a thickness of 3 millimeters (mm). What is the specific gravity of material used to form the tennis ball?
Show correct and step by step solution
Which could be the applied force in Newtons of a moving plate (area 0.1m2) and (v=2m/s) in between two different fluids: %3D over the plate: 3mm of Fluid 1 with viscosity of 0.001 Pa-s under the plate: 4mm of Fluid 2 with viscosity of 0.002 Pa-s O 0.18 O 0.17 O 0.19 O 0.15 O 0.16 O 0.20
The volume and temperature of air (assumed to be an ideal gas) in a closed vessel is 2.87m³ and 300 K, respectively. The gauge pressure indicated by a manometer fitted to the wall of the vessel is 0.5 bar. If the gas constant of air is R = 287 J/kg K and the atmospheric pressure is 1 bar, the mass of air (in kg) in the vessel is
For a Newtonian fluid flowing in turbulent flow conditions, show the effect of increasing the flow rate by 2 times on the pressure difference and the effect of increasing the pipe diameter by 25% on the pressure difference mathematically (without using numerical values). On the condition that everything else remains constant, show the effect of increasing the pipe diameter on the flow, the effect of increasing the pipe length on the pressure difference and the effect of increasing the pipe length on the flow mathematically (without using numerical values).Show mathematically (without using numerical values) how the pressure difference will be affected if you use two parallel pipelines with a length equal to half the length of the first pipe and equal diameter to the first pipe instead of one long pipeline.