The line currents of unbalance delta connected load are: lb-40 cis 240 degrees, la-50 cis 0 degree, Determine the phase B zero sequence component. . A. zero B. 45-1.2.9 Ic=45.8 cis 130.9 degrees. C.16+j7.25 D. 5-j2.9

The line currents of unbalance delta connected load are: lb-40 cis 240 degrees, la-50 cis 0 degree, Determine the phase B zero sequence component. . A. zero B. 45-1.2.9 Ic=45.8 cis 130.9 degrees. C.16+j7.25 D. 5-j2.9

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.14MCQ: The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load...

See similar textbooks

Related questions

Q: Find the currents flowing in the circuit in the figure below. (Assume the resistances ar 1₁ 1₂ 33 13…

A: The given circuit diagram is shown below,…

Q: Derive the voltage gain equation for the single-ended primary-inductance converter (SEPIC) shown.…

A: Given data A chopper type of electrical circuit is given in the problem. Two inductors L1 and L2…

Q: 2002 3 ww (1) (5 0000 [ (syr

Q: When do we use Thevenin’s and Norton’s Theorem? answer asap in paragraph form ty

A: Use of thevenin's and Norton's theorem. Any linear two terminal circuit can be indicated by a…

Q: The diode in the circuit is biased and the voltage across it is volts. 100 V

Q: Simplify F=A’B’C’ + A’B’(C’+C)+ABC

Q: Consider the circuit shown below: 6Ω ww j8Q2 000 O ww 20 Ω If the total average power absorbed by…

A: Given- Given circuit- Power absorbed=4400 W, To Find- The value of the average power absorbed by…

Q: Design an emitter follower circuit having input impedance 500KS, output impedance of 2002 with uses…

A: Given: Zi=500 kΩ, Z0=20 Ω, hie=1 kΩ, hfe=50 and hoe=25 μAV.

Q: Choose from below the KMAP of expression : X'YZ+XY'+W

A: The K-Map is used to find the simplify the boolean expression and the provides the minimum number of…

Q: SOLVE THE CIRCUIT BY USING SUPERPOSITION THEOREM TO FIND THE CURRENT FLOWING THROUGH EACH RESISTOR

A: It is given that:

Q: What size ungrounded conductors do we need for the 60 amp load? All conductors have typeTHHN…

A: The length of the circuit, the permitted voltage drop, and the surrounding temperature are some of…

Q: 8. The effect of high-frequency discharges on current transformers used in high-voltage circuits is…

A: The correct answer is A. porcelain insulator bushing. Current transformers (CTs) are used to measure…

Q: 12. Use NAND gates, NOR gates, or combinations of both to implement the following logic expressions…

Q: The Laplace transform of the following function is: f(t) = e-5tr(t) +2sin(3t)u(t) Select one: O F(s)…

Q: The op amp in the circuit shown is ideal: RI= 3KΩ, RF1=2KΩ, RF2=6KΩ, RL=10KΩ, RA=RB= 1KΩ, Vin=10V…

Q: 1. For a non-linear amplifier with two input frequencies, 3kHz and 8kHz, determine a. First three…

Q: The circuit shown in the figure consists of a real battery with emf, ε = 24 V, and internal…

Q: Solve the circuit using MESH METHOP 201 бл $62²2² 1523 182 1522 2012 7V

Q: AN -10-3 For the signals studied in problem 6-3 above, we can approximate the bandwidth of the…

A: Assumption for the message signal ωc=2π×10-7 rad/sec Kf=104π Kp=25π fc=10 MHz From the waveform,…

Q: Q.1) The impedance of 0.5H is __ _

A: Impedance: It is nothing but the opposition offered by the passive elements to the AC current Henry…

Q: Simplify F= A’ + A’B’C’D’ + A’B’CD’ + A’B + A’B’C’D’ + C’D + CD’

A: We need to simplify the given Boolean expression.

Q: 20. Which one of the following conditions tends to demagnetize the core of a current transformer? A.…

A: C. Opening the primary at the peak of the cycle at heavy load can tend to demagnetize the core of…

Q: Calculate Vo, Id, Ir and the Power in each diode for the circuit below.

Q: 1 eBook How much is ZT for a 100 Q R in series with a 100 2 inductor? Multiple Choice O O 100 92…

Q: Ass 18 (a) Find the voltage vy in the circuit in Fig. P2.18. (b) Show that the total power generated…

Q: 1. Free space propagation: Assume the transmitter power is 1 W at 60 GHz fed into the transmitter…

A: Given: Transmitter power: Pt = 1 W Frequency: f = 60 GHz Transmitter and receiver antenna gains: G =…

Q: How can the quality factor of the half-wave rectifier circuit be increased?

A: The quality factor or Q - factor is a measure of the performance of a circuit.

Q: + is ( 1 ) 10 ΩΣ |υ 6023 40 μΗ 1 μF Click to see additional instructions The sinusoidal current…

A: Given that IS = 3 cos (200000t) A C =1 micro farad L = 40 micro Henry R1 = 6 ohm, R2 =10 ohms

Q: Calculate the electric field intensity E at M(3, -4, 2) in free space caused by: a. Charge Q1 = 2…

Q: Using Kirchhoff's rules, find the following. (₁ = 71.0 V, &₂ = 61.4 V, and 3 = 79.0 V.) 4.00 ΕΩ ww…

Q: B: For the circuit shown, is this a possible Bode Plot? R1 www Va *I C1 Vb 40db Gain Frequency

A: Yes this is a possible bode plot. Because transfer function of the circuit will be H(s) =…

Q: (f)

Q: Output signal Vout has the waveform shown below. Incoming sine wave Vsig has OV of dc offset and its…

A: According to the question, for the given circuit as shown below The output waveform is given as We…

Q: Why in high voltage system, we prefer direct or small resistance? How to define…

A: As per the company guidelines, the answer to the first 3 subpart can be given, ask the fourth…

Q: Consider the system given by X AX + Bu, y = CX + Du = A = [ ²¹₂ ¹₁] B =[₁] C = [10] D = [0] Is the…

Q: 4₁ 12V 13 Find the current in each resistor. R₂=18 02 R,₁=210R₂=160R₁=122 ms's, R6=1.20 15V R₁ = 28…

Q: Q5) Find the minimum SOP for each of the following using K-maps: a) f(a,b,c) = mo+m2+m5+m6 b)…

Q: An AC motor rated for 600 rpm synchronous speed is connected to a 60 Hz electrical supply. Determine…

A: Given data:- Synchronous Speed of the motor Ns=600 rpm The frequency at which the motor operates…

Q: What is the apparent power given by a source that, in a circuit, feeds 525 V at 50 Hz to a resistor…

A: here we have to find the apparent power of the circuit.

Q: 1. Find the no-load phase and line voltage of a star-connected, 4-pole alternator having flux per…

A: Given data Pole is P=4 Flux per pole is φ=0.1 Wb Number of slots per pole per phase m=4 Double…

Q: Problem 3. Block Diagram Inversion Find the equation of motion and the initial conditions for the…

Q: 12. If a current transformer has an RCF of 1.0028 and a PACF of0.9955, the value of TCF is A. 0.9994…

A: Given: RCF = 1.0028, PACF = 0.9955, To find: The value of TCF.

Q: Y, Z 00 01 11 10 x 00011 01 x x 0 0 11 1 X 10 0 X X Question 1. Which group color that eliminates 2…

Q: The ABCD constants of a 60 Hz, 3-phase long transmission lines are as follows B = 191.62/79.1⁰ C =…

Q: Is the following signal x(t) periodic? If so, then find the fundamental period of x(t). 7π x(t) = 2…

A: In this question we need to check the given signal is periodic signal or not if the signal is…

Q: + v υ 10Ω i₁ 603 40 ΜΗ· 1 μF Click to see additional instructions The sinusoidal current source in…

A: here we have to find the current i3.

Q: Q3. Find the Thévenin equivalent with respect to the 7k2 resistor.

A: The thevenin's equivalent circuit can be obtained by calculating the open circuit voltage and…

Q: 6. A system is described by the following differential equation. Find the expression of the transfer…

Q: 2 Vo = V₁ + √√√ (VDD − V.)² — r(v₁ – V.)²

Q: Write down and explain the meaning of all terms associated with data quantification.

A: Answer: to explain the meaning of all terms associated with data qualification

Concept explainers

Single Phase AC Circuit

Alternating Current (AC) is a type of electric power in which the electric current changes, both in magnitude and direction, at regular intervals. This AC Circuits can deliver power in either a Single Phase system or a Three Phase system.

Question

Polyphase Circuits

The line currents of unbalance delta connected load are:
lb-40 cis 240 degrees,
la-50 cis 0 degree,
Determine the phase B zero sequence component.
. A. zero
B. 45-1.2.9
Ic=45.8 cis 130.9 degrees.
C.16+j7.25
D. 5-j2.9

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis of Single Phase and Three Phase System

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
Power factor correction is usually done by adding _________ to the load circuit.Select the correct response:a. switchb. capacitorc. inductive loads
The p.u. impedance value of an alternator corresponding to base values of 13.2 kV and 30 MVA is 0.2 p.u. Then the p.u. impedance value of an alternator for the new base values of 13.8 kV and 50 MVA is......
A 50 Hz, Scott connected transformer supplies an unbalanced two phase load at ( 400 V) per phase. For the leading phase the load has a resistance of (13.3 ohm) and capacitor of (318) micro farad in series. For the other phase the load consists of resistance (10) ohm and an inductance of (42.3) mH. Calculate both mathematically and graphically the lines currents on 3 phase side. The main transformer primary to secondary turns ratio is (12/1).
Please help with this balanced three-phase circuit problem.
6.5% ans ex A so kvA. 2o00/20 V, So He single-phase transformar has impedance drof of8% and resistance drop of 4%. Caleulate. The Requlation of the Thams former at full- Load o8 P.s Legging. also find The Power factor at which Voltage requlation will Be Zero. Sols 0.5 leading. s alculate The % Noltege Requlation af atransformar in w hich the Percantage resistance drof is 1% and Percentage dre is 6% when The Power fador is 0.8 lagging ) > unity aMS 38 % ans 1 % (シ→ 0.8 leading . amS - 2.2%
2) The one-line diagram of a three-phase power system is as shown in Figure. Impedance are marked in per-unit on a 100-MVA, 400-kV base. The load at bus 2 is S2=15.93 MW - j33.4 Mvar, and at bus 3 is S3-77 MW + j14 Mvar. It is required to hold the voltage at bus 3 at ...L0 kV. Working in per-unit, determine the voltage at buses 2 and 1. (Please determine the voltage magnitude within the specified limits: 410-450 V. By considering the voltage magnitude value you determined yourself, solve the question.) V₁ j0.5 pu V₂ j0.4 pu S₂ Figure V3 S3
A three-phase balanced load of 15A per phase is supplied by a steel wire armoured cable with a c.s.a. of 2.5mm². The voltage drop for this cable is 15mv/A/m and the circuit is 40m long. Calculate the voltage drop in the cable.
Connect three single-phase transformers in Y-Y, with subtractive polarity, so that the line-to-line voltages on the primary are 30 degrees delayed to their respective line-to-line voltages on the secondary. It should show each step that is needed to make this connection (example: the phasor diagram) and should show the final connection of the three transformers including the polarity markings. Assume phase A on the primary is terminal "H1".
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Ztoad 500 236.87° ohm , and the transmission line's impedance is Zine = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
Describe the star-delta connection configuration types in three phase transformers and their necessity by drawing and writing. Thank you very much if you answer.
Two sinusoidal currents are given by i1, and i2. The absolute phase difference between them is ___ degrees.