The length of the crest of a trapezoidal weir is 2m. the sides are sloping at 75 degrees 57' 49" with the horizontal, if the head on the weir is 0.5 m, 1. Prove if it is a Cipolleti weir or not 2. Find the discharge in cu. m/s

The length of the crest of a trapezoidal weir is 2m. the sides are sloping at 75 degrees 57' 49" with the horizontal, if the head on the weir is 0.5 m, 1. Prove if it is a Cipolleti weir or not 2. Find the discharge in cu. m/s

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I need the answer as soon as possible
A channel carrying 105.86 ft³/s. Assuming that an error of 0.05904 in is made in measuring the head, determine the resulting percentage of error in discharge. (a) If a 90º triangular weir is used. (b) If a Cipolletti Weir 10ft long is used. Draw the sketch
A 119-degree V-notch-weir was installed to measure the flow in an artificial channel. The crest of the weir is located 2.25m high relative to the channel bed. Depth of overflow above the crest is 0.41m. Determine the discharge in L/s. Neglect velocity of approach. c = 0.58.
-1/3 A long channel of rectangular cross-section with width 3.5 m and streamwise slope 1 in 800 carries a discharge of 15 m³ s¹. Manning's n may be taken as 0.016 m s. A broad-crested weir of height 0.7 m is constructed at the centre of the channel. Determine: (a) the depth far upstream of the weir;
a rectangular suppressed weir is placed on the side of a reservoir whose plan area is a constant 1034m^2. When the weir is opened the flow reaches elev 5.13m eventually it reaches 4.88m If the crest is situated at 4.46 when the wier is opened how long does it take to lower the depth flow to 4.88m? the weir is 2m long and has c=0.61
A submerged sharp crested weir 0.75 m high extends across a rectangular channel 3 m wide. The depth of water in the channel of approach is 1.22 m and 20 m downstream from the weir the depth of water is 0.92 m. Determine the discharge on the submerged weir assuming the nappe remains on top. 1.22m 0.92m 0.75m 1.57 m^3/s 2.06 m^3/s 4.785 m^3/s 2.45 m^3/s 20m
4. Determine the discharge of the weir having a head of 1.5 m (in L/s). C = 0.61 A) If V-notch were used, 0 = 75° B) If a trapezoidal weir with sides inclined 10° with the vertical and a length of crest is 3 m C) If a rectangular weir 2 m long is used
Determine the discharge (L/s) at the weir having a head of 0.813 m. if it is a trapezoidal weir with sides inclined 14.94 degrees with the vertical and a length of crust of 5.38 in. Use Cd = 0.661 and Cd = 0.641
Determine the vertex angle (in deg.) of a V-notch weir for a discharge of 29,762 L/s and a head of 4.49 m. Use Cd = 0.942. Round off to two decimal places.
The flow rate of water in a 3-m-wide horizontal open channel is being measured with a 0.25-m-high sharp-crested rectangular weir of equal width. If the water depth upstream is 0.9 m, the flow rate of water is(a) 1.75 m3/s (b) 2.22 m3/s (c) 2.84 m3/s(d) 3.86 m3/s (e) 5.02 m3/s
குUடும் UTM Water is flowing in a 250 cm w cm width rectangular channel with a unit discharge of 2.4 1/1000 and 0.012 s/m¹/³, The channel bed slope and respectively. If broad Manning's n are a b crested weir is constructed in the channel, determine the height of weir which will create backwater and the flow depth at just upstream of the weir should not exceed 5% of the normal depth. I flow depths above, upstream UTM & UTM 00m³/s.m. Calculate and downstream of the constructed weir. Sketch the flow profiles in the channel and the e the expecte UTM specific energy curve which describes this problem. UTMUTSC &UTM & UTM &UTM
In 28.5 secs, 35,579 L of water is collected. The length of the rectangular weir is 2.15 m, the crest is 450 mm high from the channel bed and it should maintain a constant head of 275 mm. Determine the velocity of approach. Assume there is head loss.