Answered: the internal torque diagram. Find the…

the internal torque diagram. Find the maximum shearing stress on a section 3 m from left end of the shaft. The rotation of a section 2 m from left end of the

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A long shaft of diameter d is subjected to twisting moment T at its ends. The maximum shear stress acting is equal to A zero B с D 16T d³ 32T +d³ 64T +³
3
Figure Q2 shows a statically determinate plane truss subjected to a horizontal concentrated load at B. The truss is made using steel with Young’s modulus of 205 GPa, and the cross section area for all members are constant. If the horizontal displacement at B is limited to 10 mm, determine the minimum cross section area required for the truss. The solution can be based on Method of Conservation Energy or Method of Virtual Work.
A compound shaft ABC (composed of two parts AB and BC) is subjected to a torque-load shown in the Figure. Support A allows angular-twist not to exceed 0.5 degree, while support C is rigid. Given that part AB has solid circular section (r= 15 cm), while part BC has tubular circular section (r= 15 cm; t = 2 cm), and for given geometry: a) Determine the maximum shear stress in the shaft. b) Determine the angle of twist on. c) Determine the relative angle of twist o G-70 GPa # * 2m 450 kN.m B
A force of 521 kN is applied at joint B to a system of two-pinned joined bars shown in the figure. Determine the required cross-sectional area of the bar BC if the allowable stresses are 175 MPa in tension and 74 MPa in compression. 521 kN B 1.5 mt 1.5 m 3.0 m 3.0 m
A cross-section is subjected to a maximum shear of V=160 kN (see figure): Determine the centroid of the cross-section. Calculate the moment of inertia (I) of the cross-section. Determine the shear stress at point A in the cross-section.
The sleeve bearings at A and B only support vertical forces. Determine the absolute maximum bending stress in the 1.2 in diameter shaft which is subjected to the concentrated forces
A circular shaft which has a diameter of 100 mm is subjected to torque of 5 kN-m. The shear stress in N/mm2, induced in the shaft would be A B D 160 TT 120 π 125 π 80 E TT
A torque of magnitude T = 1000 N-m is applied at D as shown. Shaft AB and CD have an elliptical cross-section. The major and minor diameters of shaft AB are 56 mm and 50 mm respectively, while the major and minor diameters of shaft CD are 42 mm and 38 mm respectively. Find the maximum shearing stress in shaft CD. Answer must be in MPa
Determine the variation in the width w as a function of x for the cantilevered beam that supports a concentrated force P at its end so that it has a maximum bending stress sallow throughout its length. The beam has aconstant thickness t.
A pipe with a weight of 3.7 kg/m is attached to a wall such that all degrees of freedom are restraint. At the free end of the pipe a vertical load P=100 N pointing downwards is introduced with an excentricity of 100mm from the axis. The pipe has an length of 1m and is made of steel with the Young's modulus of 210 GPa and the Poisson ratio of 0.3125. The moment of inertia is l=19.7 cm“ whereas the polar moment of inertia J = 2 I. First, as part of the mechanical properties determine the Shear Modulus. Then determine the total vertical deflection at the point where the vertical load is being introduced. Note: Use the principal of superposition. ANSWERS: Shear Modulus %3D [MPa] Vertical deflection due to weight only [mm] Vertical deflection due to End-Load (excentricity NOT considered) [mm] Vertical deflection due to excentricity of the End-Load only [mm] Total vertical deflection [mm]
The pole is supported by a pin at B and A-36 steel guy wire AC. If the wire has a diameter of 0.2. Modulus of Elasticity of Steel = 200GPA or 29x103 ksi Poisson's ratio of steel=0.321 3 ft 30 D 2.5 kip 4 ft B 1. At what angle is the principal stresses on pole BC? Use Mohr's Circle. 2. What is the principal stress in pol BC? Use Mohr's Circle 3. Draw the stresses on a unit element acting on 35-degree clockwise direction of pole BC. Use Mohr's Circle. 4. What are the principal stresses in point D? Use Mohr's Circle. (answer in ksi) 5. At what angle is the principal stresses acting on point D? Use Mohr 's Circle. 6. Draw the stresses on a unit element acting on 35degree-clockwise direction of point D. Use Mohr's Circle. (answer in ksi)