The internal pressure of a cylindrical tank is given as 1150 KPa. If the allowable strength at the longitudinal joint is 500 KN/m while the allowable strength at the girth joint is 240 KN/m, determine the maximum diameter of the cylinder tank.

The internal pressure of a cylindrical tank is given as 1150 KPa. If the allowable strength at the longitudinal joint is 500 KN/m while the allowable strength at the girth joint is 240 KN/m, determine the maximum diameter of the cylinder tank.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Answer the question quecly please Fluid
Water backs up behind a concrete dam as shown in figure Leakage under the foundation gives a pressure distribution under the darri as indicate If the water depth, h, is too great, the dam will sopple over about its toe (Point A) For the dimensions given, determine the factor of safety agarest overtuming moment if L-120 fh and h - 50 n. Base your analysis on a unit length of the dam The specific weight of the concrete is 150 ib/tt3 Water
Oil (kinematic viscosity = .0003 ft^2/s and specific weight = 53.7 lb/ft^3) flows from A (zA = 225.5 ft ) to B (zB = 235.84 ft) at a rate of 290 gpm. The pipe material is commerical steel and the pipe length from A to B is 7320 ft. The required minimum pressures at A and B are PA = 55 psi and PB = 13 psi. Determine the minimum pipe size to satisfy the pressure requirements through iteration with the Moddy Diagram. Round up the diameter to the nearest 1 inch.
UD Vein 40 40 Vein 60 S A
3. A tank open at the top, is made of sheet iron 1” thick. The internal dimensions of the tank are 4’8” long, 3’6” wide and 4’4” deep. Find the weight of the tank if empty and find the weight when full of salt water. (salt water weighs 64lb/cu.ft. and iron is 72 times as heavy as salt water). 4. A dam 100 ft. long has a cross section which is a trapezoid whose altitude is 16 ft. and upper base is 5 ft. If the lower base angles of the cross section are 50o and 65o, find the volume of material the dam contains. ?
The angular velocity wac = 5.6° per second. Determine the angular velocity of the hydraulic actuator BC in deg/s. L = 1.38 m 2L2 = 1.15 m 2L2 - Li --- L2 -
Not sure how to do this one. Would really appreciate a full solution. Thank you!
The radii of the press plunger and the pump plunger are in the ratio 30:4. If an effort of 32kgf acts on the pump plunger. Find the maximum effort the press plunger can overcome. (in kgf)
A Pump The oil tanks have a diameter of D = 12m. The initial depth of the oil in tank A is 20m, and in tank B the depth is 1 m. The pump delivers a constant head of 60 m. The connecting pipe has a diameter of b = 0.2m, and the head loss due to friction in the pipe is hyL = 8- Find the time required to fill tank B to 14m depth. (neglect minor losses)
A cylindrical tank with its axis horizontal has a length of 6 m and the ends of the tank are vertical planes, as shown in Figure Q2 (a). The vertical pipe of 0.2 m in diameter is connected to the top of the tank. The tank and the pipe are filled with ethyl alcohol to a level of 1.5 m above the top of the tank. The diameter of the tank isa (a) 2.0 m Open surface 1.5 m 0.2 m OF Bottom surface of the 2.XX т cylindrical tank FR 6 m Figure Q2 (a)
SITUATION #2 Determine the maximum diameter of the cylinder tank if the internal pressure is 127 kPa. Given the allowable stresses for longitudinal 140 MPa and tangential 100 MPa. L = 10 m