The intake in Fig. 3.1 has cross-sectional area of 0.74 m2 and water flow at 0.40 m/s. At the outlet, distance D = 180 m below the intake, the cross-sectional area is smaller than at the intake and the water flows out at 9.5 m/s into equipment. What is the pressure difference between inlet and outlet?

Q: Q. 2 Find the flow rate of water in each pipe and the pressure at point 3. Neglect the minor losses.…

A: Many combinations of pipes are connected in series, parallel, or complex networks. So by writing the…

Q: : A horizontal pipe I ft in diameter, taperv gradually Maw Q to 8 in. in dio meter, If the fIow I…

A:

Q: Figure Q4 shows there are two sections of pipes in the system, which are 38m long of 5 cm diameter…

A: Given, L1 = 38 m  L2 = 45 m D1 = 5 cm or 0.05 m D2 = 15 cm or 0.15 m \ Q = 0.005 m3/s

Q: H.w.: As shown in figure below, determine the pressure at point. A- Hg Ans.: 12.164 KPa Va cuum…

A:

Q: The flowrate of water through the bend pipe (90o) is 0.21 m3/s. The pipe diameter at the inlet is…

A:

Q: absolute roughness is 0.03mm (for both sections), Determine the height H. Neglect local losses. Tip:…

A:

Q: A circular door having a diam. of 3m closes a horizontal duct from a small diam. as shown. The…

A: given data:- diameter of gate=3 m specific gravity of liquid=0.95

Q: Problem #12 Water 118 -diameter nozzle Determine the discharge in the pipe (in cfs) and the pressure…

A: Pipe arrangement is given in the figure as shown above and it has been asked in the question to…

Q: At A, water (rho=1000kg/m* 3 and mu=1cp) at a pressure of 400 kPa and a velocity of 3 m/ s, flows…

A:

Q: Prob. # 3 (a): A 90° horizontal reducing elbow carries a flow of 12 cfs (i.e., cubic feet per…

A:

Q: Problem #2 Water 11 M diameter sin -diameter nozzle Determine the discharge in the pipe (in cfs) and…

A: Given : Determine the discharge in the pipe and pressure at point B ?

Q: An orifice is attached to a vertical side of a cylindrical tank having a diameter of 4m. The weight…

A: Given:- Diameter of tank=4 mDiameter of orifice=90 mmWeight of water discharged=22563 N in time of 1…

Q: The pressure gauges are inserted at A and B in a vertical pipe converging water.  The diameters at A…

A:

Q: A fire protection system is supplied from a water tower and standpipe 80ft tall. The longest pipe in…

A: Given that :

Q: Problem 1. A 75-mm diameter orifice discharges 0.023 m3/s of liquid under a head of 2.90 m. The…

A: Given data,  Diameter of orifice = 75 mm Discharge = 0.023 m³/s Head = 2.9 m Diameter at vena…

Q: The water is flowing through a P, 39.24 N/cm D, 20 cm Problem 6.4 pipe having diameters 20 cm and 10…

A: Given :

Q: A fluid of specific gravity 0.8 and dynamic viscosity 15 x 10-Pa s is flowing in a 15mm diameter…

A: Given that specific gravity of fluid is 0.8 Dynamic viscosity of fluid is 15×10-4Pa.s Diameter of…

Q: What are the highway culvert design criteria and sizing principles, what risks they are exposed to…

A: Brief concept introduction- Highway culvert- A highway culvert is a drainage system that allows…

Q: Pb # 2: Water at 60 °C flows in a straight 24-mm-diameter pipe (e = 0.060 mm) between points A and B…

A: Given data Registration number = 5350 Temperature of water= 60° C  Dia of pipe= 24 mm  Length of…

Q: The water is flowing through a P, 39.24 N/cm D, 20 cm Problem 6.4 pipe having diameters 20 cm and 10…

A:

Q: taining air and water is shown. At the closed end of the manometer the air pressure is 16…

A:

Q: 4) Water flows through a contraction section as shown. A pressure gage connected between the…

A:

Q: A (300mm) diameter of pipe, if the discharge (90 L/sec), nozzle diameter (75mm) and pipe length from…

A: Due to unavailability of Math type software, providing Hand written solution

Q: The water is flowing through a P, 39.24 N/cm D, 20 cm Problem 6.4 pipe having diameters 20 cm and 10…

A:

Q: compute the force acting on the flange.

A:

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?