The inputs to a digital circuit are having the signals of A, B and C has +5V power supply (logic 1) and the ground (logic 0) are available. The output of the circuit is X=A'B+A'B'C' a) Write down the output function(X) in its canonical SOP and POS forms (b) Implement the circuit of output function(X) using only two 2:1 multiplexers.

The inputs to a digital circuit are having the signals of A, B and C has +5V power supply (logic 1) and the ground (logic 0) are available. The output of the circuit is X=A'B+A'B'C' a) Write down the output function(X) in its canonical SOP and POS forms (b) Implement the circuit of output function(X) using only two 2:1 multiplexers.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider the signal x[n] shown in the figure x[n] IIIIIII -2-1012345 Which one of the following signal is an EVEN signal? x[n] is already an even signal b. x-n) is an even signal x[n] + x[-n] None of the other answers x[n] - x[-n] d.
1) If the given waveforms are the inputs of AND gate draw the output waveform. a 1 C 2) The above given waveforms are the inputs of OR gate draw the output waveform. 3) Waveform a is the input of a NOT gate draw the output waveform.
Determine teh output of teh DAC in Figure (a) if teh waveforms representing a sequence of 4-bit numbers in Figure (b) are applied to teh inputs. Input DO is teh least significant bit (LSB). 200 kN Doo W R 0 12 3 4 5 6 7 8 9 1011 12131415 100 kN +5 V Do +5 V DI +5 V D2 +5 V iiii D3 D 10 kN 50 kfl D2 0 W- 25 kN D3 0- (a) (b)
An analog signal varying between 1V and 3V will be converted to digital and the signal voltage value will be displayed on the LCD screen. The signal to be measured will be between 1V and 3V. 3 analog signals will be read using the AN5, AN6 and AN7 pins. Values in these signals will be displayed one by one on the LCD screen as digital and voltage values. Draw the circuit diagram and write the PIC C codes.
A 3-bit ADC with a reference of 10V is used to sample a DC signal. What is the outpout D2.DO for an analog input Vin= 3.349 V Select one: O a. D2.D0 = 100 O b. D2.DO - 101 Oc. D2.D0= 011 O d. D2.D0 = 111 Oe. None of the mentioned.
H1. a sampling technique was used in digitally encoding analog data and 2048 distinct voltage levels were recorded. What size code is needed Explain with details and show step by step explanation
Q1/B/ Determine the analog voltage output for the Figure shown below if the waveforms representing a sequence of 4-bit numbers in the Figure below are applied to the inputs. Input Do is the least significant bit (LSB), where Input Digital Signal are (Do = 0001), (D1 = 0010), (D2 = 0100) and (D3 1000). While Digital Voltage is 5v. %3D %3D 80 kn De o R 40 kn 20 kn 20 kn Dz O 10 kn Vout(Da) Vout(D) = - Vout(o) -. Voutcb)
Question 8 160 Which of the po160100555- 870479447 In the DAC unit, the analog level at the A 1601005559870479447 g160100555 B 0870479447 There may be applications that require digital-to-analog conversion but do not need analog-to-digital conversion. 9870479447 1601008 9441 Basically, the process is the reverse of the conversion) changed and in this 160 0555 - 987 9441 The signal produced by this conversion process can basically be 555-987 s respect it is similar то 916 It would not be possible to produce a realistic sine signal with a 4-bit DAC unit. 087047944 to the PWM unit. 1601008 160100555 measured with a DC multimeter. 2555-987047944 g160100555 - 7944 9168
Hi i am trying to convert a pwm signal to a ramp signal, i have an output that currently generates around 26mA but I want a ramp current signal that will range between 0 -100mA depending on the duty cycle of the PWM . so this means that the circuit should include an amplificator to get the current to 100mA. can you please draw the circuit thank you
If the four input lines of a multiplexer are DO, D1, D2 and D3, and the two select lines are given inputs as 11, then the output of the multiplexer is O a. D2 O b. D3 O c. D1 O d. DO
Consider a PV Module with 4 solar PV cells with the Size of each 10cm x 10cm are connected in Parallel. If we connect a lamp load of 2W across this module, choose the correct statement for the above PV Module. (Assume necessary data) a. The output voltage is 0.5V, the output current is 2A b. The output voltage is 0.5V, the output current is 4A c. The output voltage is 2V, the output current is 2A d. The output voltage is 2V, the output current is 4A
Realized a 4X1 multiplexer in the block diagram shown below. What is the output equation of the given multiplexer? Also draw the circuit diagram. N.B: Follow the instruction given in the figure to choose the input and output names. "First Letter of your Name"| 10 I1 | "Third Letter of your Name" 4X1 "Second Letter of your Name MUX 12 13 B