The inner radius of the pressurized cylindrical tank is 1.25 m and the wall thickness is 15 mm. It is made of steel plates welded along the seam açılı θ = 60 angles. If the pressure vessel is subjected to an internal pressure of P = 10 MPa, find the normal and shear stress components along this seam. Also, calculate the principal stresses for the given loading condition

Q: 2000 1 45001 3100 N

A: given; force in x-direction(Fx)=-2000N (compressive)force in y-direction(Fy)=-4500N…

Q: Oy Txy

A: given; normal stress in x direction =σxnormal stress in y direction =σyshear stress in xy…

Q: A steel tube of 200 mm external diameter is to be shrunk onto another steel tube of 60 mm internal…

A: For inner tube: Write the expressions for A and B for thick cylinder. At r=0.030,…

Q: The major and minor principal stresses are 3 MPa and -3MPA respectively. The maximum shear stress at…

A: Given data : Major principal stress=3 MPaMinor principal stress=-3 MPa

Q: The stresses shown on the left below act on horizontal and vertical planes through a point on the…

A: Principal stress is defined as the maximum or minimum value of normal stresses and they act on that…

Q: Determine the maximum and minimum hoop stresses across thesection of a pipe of 400mm internal…

A: Givendi=400mmt=100mmP=8 N/mm2=8MPa

Q: A typical stainless steel cylindrical vessel is shown. The inside diameter of the tank is 48.0 in.…

A:

Q: Use Mohr’s circle to determine the principal stresses at the point. Also, find the corresponding…

A:

Q: Determine the equivalent state of stress on an element at the same point oriented 60° clockwise with…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: 2. Consider the Flamant solution - a line load on the edge of a half space. The valid stress…

A: according to a given question

Q: if the maximum and minimum principal stresses at a point are (27 Mpa) and (5 Mpa) respectively. The…

A: Maximum shear stress is equal to difference of maximum principal stress and minimum principal stress…

Q: A closed cylindrical tank containing a pressurized fluid has an inside diameter of 320 mm and a wall…

A:

Q: Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal…

A: Step 1: Step 2: Step 3: Step 4: solution is given above

Q: The steel water pipe has an inner diameter of 12 in. and wall thickness 0.25 in. If the valve A is…

A: (a) Longitudinal Stress = 0 ksi (b) Hoop Stress = 7.2 ksi

Q: 1. Find the flexural stress at point A 2.5 kN/m 2.25 m 3.5 m

A:

Q: 3. For the state of stress shown below, calculate the principal stresses and maximum shear stress.

A: σx = 90 Mpa σy = -60 Mpa Txy = 20 Mpa

Q: The cylindrical pressure vessel has an inner diameter of 750 mm and a wall thickness of 9 mm. The…

A:

Q: Determine the equivalent state of stresses in an element at the point representing (a) the principal…

A:

Q: In a simulation carried out by a team engineers a state of plane stress in a machine base of a…

A: To find - 1. The principal stresses and the maximum in- plane shear stress acting at the point.…

Q: Determine the equivalent state of stress on an element at the same point which represents (a) the…

A: Givensig1=σy=-17MPasig2=σx=5MPash=τ=12MPa

Q: 80 MPa 60 MPa

A: Consider the given plane figure on x-y plane. From the figure, Stress in x direction = σx = 0 MPa…

Q: b) For the thin walled pressure vessel subjected to an internal pressure of 150 psi and as shown…

A: Permissible stress is stress which produces due to pressure or forces which does not exceed the…

Q: For the thin-walled pressure vessel subjected to an internal pressure of 150 psi and as shown below,…

A: The stress that acts in parallel direction with the longitudinal axis is called longitudinal stress…

Q: Q2 / The 60° strain rosette are mounted on articular cartilage element. Figure Q2 shows the readings…

A: Consider the diagram shown below for the strain rosette. The general equation for the strain in a…

Q: For the shown element, what are the principal stresses and their orientations (ew, cew), draw the…

A: (a) To find: The principle stress and the orientation of principle stress Given: The stress in…

Q: The state of stress at a point under plane stress — 40 MPа, Суу condition is Oxx 3D 100 MPа and Txy…

A: Given, Stress in x-direction = σx = 40 MPa Stress in y-direction = σy = 100 MPa Shear stress in x-y…

Q: The stresses on an element are o, = -300 psi and o „=-600 psi. Find the maximum shear stresses on…

A:

Q: The billboard shown is supported by structural tube that has a 380 mm outer diameter and 38 mm wall…

A: Given: The outer diameter of pipe, D = 380 mm = 0.38 m The thickness of pipe, t = 38 mm = 0.038 m…

Q: A 28mm diameter round steel bar is 0.4m long. It is placed concentrically within a brass tube which…

A:

Q: 4. The steel water pipe has an inner diameter of 100 mm and wall thickness 5 mm. If the flow of…

A:

Q: In order to increase the strength of the pressure vessel, filament winding of the same material is…

A: The pretension condition- The width is same for the wall and filament w, and the thickness of the…

Q: The ring, with dimensions shown, is placed over a flexible membrane which is pumped up with a…

A: (a) To find: The axial force F in the ring in terms of p, w and r; Calculation: Consider a FBD by…

Q: nd hemispherical shells, The bol and the 25 mm diameter bo able normal stress of 150 M

A: given data  tank thickness = 50 mm no of bolt/ length = 40  dia of bolt =25 mm allowable stress for…

Q: Determine the equivalent state of stress on an element if it is oriented 30° clockwise from the…

A:

Q: The 1 inch diameter rod is subjected to the loads shown below. Determine the state of stress at…

A:

Q: T P y=-38 MPa Try = 33 MPa q=52 MPa x

A: Consider following plane stress element:here,Find:The principal stresses andThe maximum in-plane…

Q: t a point in a strained material the principal stresses are 200 N/mm2 (tensile) and 120 N/mm2…

A: For the solution refer below images.

Q: Calculate the normal stresses (in Pa) at point Bof the bracket caused by the 25139 N force. - 540 mm…

A:

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.