"the Influence lines and Complete the Table E is 4m away from point A Point A в C D A 8m + 4m, 4m Reaction influence lines shear force at C) Bending - By Ay Dy Sc Mc x(m) 24EBCA

Q: 8 ft 6 ft· 20 k D↓ -6 ft B 20 k -6 ft- E 15 k -6 ft- Case #1: Find ABy and ACx EA = constant E =…

A: Find: Vertical deflection at B and horizontal deflection at C

Q: Write shear and bending moment equations and draw it for beam shown in figure below

A:

Q: Input the Bearing value shown below in the answer box: -Please be sure to use the ddd.mmss format in…

A: Given Data- Given bearing S 23o 02' 11"W It is needed to convert this bearing as per the given…

Q: FIND THE GENERAL SOLUTION (Do+2D² -15D)y=D0

A:

Q: water flow by an angle 0 = 45° from the flow direction while accelerating it. The elbow the inlet…

A: To Determine What is the magnitude of the resultant force in the x direction FRx  What is the value…

Q: Define dilatometer test.

A: Dilatometer test is an in situ test method used to assess the strength and deformation of…

Q: why set of standard weight used in calibration platform balance?

A: Calibration is the process of putting the scale through its paces to ensure it has the precision you…

Q: Shall reversible moisture movement be taken into account in estimating movementfor movement joints?

A: Brief concept- Moisture- Water content in form of vapours or droplets is termed as moisture and its…

Q: Find end moment slope de fiction use 100kN

A: We have 5 members in this figure. 4 fixed support. The load is acting on a mid span of AC This is a…

Q: verity of seismic forces.

A: The sudden release of energy from the Earth's crust leading to production of waves which cause…

Q: Determine the centroid coordinates (x̄ , ȳ) for the solid and homogeneous beam section shown in…

A: Determine the centroid coordinates (x̄ , ȳ) for the solid and homogeneous beam section shown in…

Q: When does measurement error occur

A:

Q: Determine maxium principal plane

A: We have to determine the maximum principal plane.

Q: Write the formula for the effective length factor?

A: The effective length factors of columns  plays major role in the design of compression members.…

Q: List and tabulate all the cases of Super position

A: According to superposition method , " At any point along the beam, the slope or deflection is equal…

Q: What is base flow separation?

A: It is required to answer about what is base flow separation?

Q: The information shown in this attached document. This has been extracted from the Expert Panel…

A: The order of construction in civil projects can vary depending on the specific project and its…

Q: O Determine the centroid coordinates (.gy for the solid and homogeneous beam section shown in Figure…

A:

Q: Problem 4. Determine the location of the centroid of the shape measured from the given axes. -3 in.-…

A:

Q: In certain building operation, it was necessary to remove a portion of B hall which was…

A: Calculate the volume of the above solid with the help of the prismatoid formula: where; V is the…

Q: Matching Type: Match the real beam to the corresponding conjugate beam 1. 2. 3. 5. & 6. 7. 8. a. b.…

A: Objective: To match the given beams to the given conjugate beams.   The transformation of supports…

Q: What does it mean if a beam is “non-compact

A: Beam is defined as a structural horizontal element which is used for resisting loads which are…

Q: What is a Isohyetal method? What is a Thiessen Polygon?

A:

Q: 2) An 8m steel tape was purchased and advertised as follows: Standard temperature Standard Pull Таре…

A:

Q: What is ASD method

A: Allowable Stress Design (ASD) It is also known as the service load design or working stress design…

Q: railroad curve has De = 5°00', I = 28°00', and I station e requested values. 37+45.00 ft. Use the…

A: Degree of the curve, Dc = 5oDeflection angle, I = 28oPI station = 37+45 ft

Q: How do I find the horizontal analysis

A: Horizontal Analysis of financial statements is an analysis method that represents the changes that…

Q: Describe the TRD method.

A: TRD stands for Trench Re-mixing and Deep wall. It is a one-phase process for excavation and in situ…

Q: What are stability and normality tests?

A: Normality: It is defined as the state of the data distribution that will occur as a normal…

Q: Define influence line diagram. Give a brief answer about uses of influence line diagram,

A: The given Question is Related to Influence line Diagrams.  Our aim is to Define what is mean by…

Q: An Engineer measured the distance between two locations on a plan having a scale of 1 cm = 50 m as…

A:

Q: Give me right answer Draw a flowchart on how to analyze a flexural member with rolled W-shape bent…

A: The flow chart for analysis of flexure member with rolled W-shape bent is shown below: (The flow…

Q: Show step by step solution

A: FINAL ANSWER:-       Therefore,the minimum coefficient of friction is 0.2167.Explanation:

Q: Calculate Shear and mement chpph beluw. Shuchure has diagram for to One Inlarnal tinge. 5KIFF Loft…

A:

Q: Given the following: b=380mm d=530mm fc'=30MPA fy=320MPa Mu=650KN-m Determine As A. USE NSCP 2015,…

A: Given,

Q: Define Earth pressure loads

A: Pressure is defined as force acting per unit area of the body.

Q: a) top most, lef tmost FIND: b) botton-most, right-most 3cm S.ם r= 1.25 y 125 } 05 Vb cm 1.5 3 I 1,5…

A:

Q: For the given structural steel sections below, determine the following: a. The location of the…

A:

Q: Define Load versus deflection plot and also show it diagrammatically.

A: Load:- The applied force, distortion, or velocity to structural components is referred to as a…