The I-beam supports the 1110-lb force and the 1430-lb-ft couple, applied to the 1.5-ft strut welded to the end of the beam. Draw the shear and moment diagrams for the horizontal beam. Then answer the questions. The distance x is measured from the left end of the beam to the right. 1430 lb-ft 1110 lb 9 1.5' A B 5 -2.0' -2.0' 2.0'

The I-beam supports the 1110-lb force and the 1430-lb-ft couple, applied to the 1.5-ft strut welded to the end of the beam. Draw the shear and moment diagrams for the horizontal beam. Then answer the questions. The distance x is measured from the left end of the beam to the right. 1430 lb-ft 1110 lb 9 1.5' A B 5 -2.0' -2.0' 2.0'

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let o-1.5m.b=3.5 m.w=50 kN/m and P = 45 kN. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. C Calculate the reaction forces A, and D, acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since A, -0, it has been omitted from the free-body diagram.) Answers: A, b KN, D, KN.
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=4.0 m, b=2.5 m, PB = 4 kN, PC = 4 kN, and MB = 60 kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise.Calculate the reaction forces Ay and MA acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Determine the bending moment acting at each of the following locations:(a) x = 0+ m (i.e., just to the right of fixed support A)(b) x = 4.0– m (i.e., just to the left of B)(c) x = 4.0+ m (i.e., just to the right of B)(d) x = 6.5 mWhen entering your answers, use the bending moment sign convention.Answers:(a) M = kN-m.(b) M = kN-m.(c) M = kN-m.(d) M = kN-m.
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=4.0 m, b=2.5 m, PB = 4 kN, PC = 4 kN, and MB = 60 kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise.Calculate the reaction forces Ay and MA acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.)Answers: Ay = kN, MA = kN-m.
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=4.0 m, b=2.5 m, PB = 4 kN, PC = 4 kN, and MB = 60 kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise.Calculate the reaction forces Ay and MA acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.)Answers: Ay = kN, MA = kN-m. Determine the shear force acting at each of the following locations:(a) x = 0+ m (i.e., just to the right of fixed support A)(b) x = 4.0– m (i.e., just to the left of B)(c) x = 4.0+ m (i.e., just to the right of B)(d) x = 6.5– m (i.e., just to the left of C)When entering your answers, use the shear force sign convention.Answer:(a) V = kN.(b) V = kN.(c) V = kN.(d) V = kN.
SHEAR AND MOMENT DIAGRAM PROBLEM 2 Use the AREA method to construct the shear-force and bending-moment diagrams for the beam shown. Let a = 6.9 ft, b = 10.4 ft, c = 5.8 ft, and w = 9.5 kips/ft. Label all significant points on each diagram and identify the maximum moments (both positive and negative) along with their respective locations. Clearly differentiate straight-line and curved portions of the diagrams. Determine the maximum shear force and bending moment in the beam. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. The roller at point D indicates that motion is restricted both up and down, and the beam will not lift off the roller. a B W b O D X
SHEAR AND MOMENT DIAGRAM PROBLEM 2 Use the AREA method to construct the shear-force and bending-moment diagrams for the beam shown. Let a = 6.9 ft, b = 10.4 ft, c = 5.8 ft, and w = 9.5 kips/ft. Label all significant points on each diagram and identify the maximum moments (both positive and negative) along with their respective locations. Clearly differentiate straight-line and curved portions of the diagrams. Determine the maximum shear force and bending moment in the beam. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. The roller at point D indicates that motion is restricted both up and down, and the beam will not lift off the roller. a B W b C D X
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=3.5 m, b=5.0 m, MB = 110 kN-m and MC = 145 kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise.Calculate the reaction forces Ay and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.)Determine the bending moment acting at each of the following locations:(a) x = 3.5– m (i.e., just to the left of B)(b) x = 3.5+ m (i.e., just to the right of B)(c) x = 8.5– m (i.e., just to the left of C)(d) x = 8.5+ m (i.e., just to the right of C)When entering your answers, use the bending moment sign convention.Answers:(a) M = kN-m.(b) M = kN-m.(c) M = kN-m.(d) M = kN-m.
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=3.5 m, b=5.0 m, MB = 110 kN-m and MC = 145 kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise.Calculate the reaction forces Ay and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.)Determine the shear force acting at each of the following locations:(a) x = 0+ m (i.e., just to the right of point A)(b) x = 3.5– m (i.e., just to the left of B)(c) x = 3.5+ m (i.e., just to the right of B)(d) x = 12.0– m (i.e., just to the left of D)When entering your answers, use the shear force sign convention.Answers:(a) V = kN.(b) V = kN.(c) V = kN.(d) V = kN.
Use the graphical method to construct the bending-moment diagram and identify the magnitude of the largest moment (consider both positive and negative). The ground reactions are provided. MB = 143 kN-m Mc = 51 kN-m Ay = 16.17 kN (down) Dy = 16.17 kN (up) 1997 4 m 5 m O 80.9 kN-m O 74.1 kN-m O 94.5 kN-m O 50.4 kN-m O 60.6 kN-m 3 m D X
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a = 2.2 m, b = 4.4 m, c = 3 m, P = 16 kN, w = 34 kN/m, and Q = 26 kN. Label all significant points on each diagram and identify the maximum shear force and bending moment along with their respective locations. Additionally:(a) Determine V and M in the beam at a point located 0.65 m to the right of B.(b) Determine V and M in the beam at a point located 1.40 m to the left of C.Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Label all significant points on each diagram and identify the maximum moments (both positive and negative) along with their respective locations. Clearly differentiate straight-line and curved portions of the diagrams. 2,400 lb 6,000 lb-ft A 3 ft 3 ft 600 lb/ft 9 ft 3 ft
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a = 5 m, b = 3 m, PB = 55 kN, Pc = 75 kN, and PE = 25 kN. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. a PB Answer: Ay = i BO PB a B Pc a Calculate the reaction forces Ay and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) D Pc D a D₂ PE a PE E kN, Dy= i -x E X kN.