Answered: The homogeneous 860-kg bar AB is…

The homogeneous 860-kg bar AB is supported by a ball-and-socket joint at A and two cables attached to B. Find the tension in cable CB.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: D 4 3

Q: Determine the support reactions at point A and the force in the cable BC when the force at F is…

A: Given :

Q: 11. The cable supports = 10 kN/m. Determine the tension in the cable at each pport A and B. the…

A: The tension is generally the cable that leads to the forces pulling on the cable from either end. It…

Q: Three loads are suspended as shown from the cable ABCDE. Knowing that dC = 3 m, determine the…

Q: will G. The 50N block C rests on uniform bar AB having a weight of 20N. The cable connecting C to B…

Q: the cable reel is in contact with the ground at A and wall B with a weight of 100 kg. If the static…

A: f= friction force on ground A=μW=0.3×1009.81=3.06 ND' alemberd principal for…

Q: The walkway ABC of the footbridge is stiffened by adding the cable ADC and the short post of length…

Q: A cable is attached to the 20-kg plate B, passes over a fixed peg at C, and is attached to the block…

A: When force is acting on the system or any structural element the two types of reaction are…

Q: cable 1 Element 1, 2 and 3 are truss elements. The system is supported by a cable. A force (P) is…

A: Given,k=3L=1M=1N=9P=1+M KNa=1+L mb=1+N α=10+5K degreesubstituting all values, we geta=2 mb=10 mα=25…

Q: The uniform 15-m pole has a mass of 130 kg and is supported by its smooth ends against the vertical…

Q: 1.2m B W N/m 1340 N 3.6 m

Q: SITUATION. The tension in the supporting cable BC is 600lbs 6' 2' B 7' 1.5' 2.5 2.5'

A: Given Tension force BC = 600 lbs

Q: Determine the tension in cable AB and the horizontal and vertical reaction components pin C exert on…

Q: Determine the tension in the cable at B, given that the uniform cylinder weighs 350 lb. Neglect…

A: For the weight to be held in equilibrium, the tension force must equal the force of gravity on the…

Q: 2.4. Two cables are tied together at C and loaded as shown. Knowing that P= 360N, Determine the…

Q: Determine the forces in cable AC and AB needed to hold the 20-kg ball D in equilibrium. Take F =…

Q: Rod AB is secured with a cable at point B and a smooth, up and down movable collar from point A.…

Q: 6.63 The cable of the suspension bridge spans L - 140 m with a sag H - 20 m. The cable supports a…

A: L=140m H=20m

Q: The rectangular beam ABC, 175 mm wide by 411 mm deep, is supported by a pin at A and the cable CD.…

Q: Cable AC exerts on beam AB a force P directed along line AC. Knowing that P must have a 350-lb…

A: Given; Vertical component of force P,Py=350lb

Q: 1.14 The uniform 300-lb bar AB carries a 500-lb vertical force at A. The bar is supported by a pin…

A: According to given data 300 lb bar AB carries a 500 lb The bar is supported by a pin at B and…

Q: The rectangular beam ABC, 175 mm wide by 411 mm deep, is supported by a pin at A and the cable CD.…

Q: Problem 3.3.10. The uniform rod in the fig weighs 600lb and has its center of gravity at G.…

Q: Determine the tension in cable AB and the force developed in smuchre AC.

Q: Calculate the reaction at support A and the value of tension in the cable BC. Take F = 80 N and M =…

A: Following is the free body diagram of the given frame:

Q: he bar supported by a pin at A and a cable at Bcarries a load of 260 N at C. Neglecting the weight…

A: T cosθ=100kn T=100cosθ=100cos60=10012=200kn…

Q: 3. A parabolic cable supports a girder having a weight of 12 KN/m. a) Determine the tension of the…

Q: Pole AB is 12 m long and its weight, W = 35 kN. It is being lifted using cables BC and BD. When the…

A: Solution Given Data Length of AB= 12 m W= 35 kN Angle= 600

Q: The sphere of weight, W = 49.05 N, is suspended by a cable with length, a = 3 m as shown. If it…

Q: Situation 6: The walkway ABC of the footbridge is stiffened by adding the cable ADC and the short…

Q: The uniform (18 kg) bar OA is held in the position the %3D 1.5 m Shown by pin at o" 60 and the cable…

A: To find tension in cable and reaction at point O

Q: 6. Determine the horizontal and vertical components of force which the pins at B, and C exert on…

Q: A 5 x 8-ft sign of uniform density weighs 270 lb and is supported by a ball-and-socket joint at A…

Q: Cable ABC has a length of 5 m. Determine theposition x and the tension developed in ABC required…

Q: Determine the tension in cable BE .and the reactions at A and D

Q: Frame OAB is supported by a ball and sockets at O and B in addition to the cable CD. The frame is…

A: The given figure is shown below:

Q: 4m 4m 2m 1 P.

Q: 3. The cable BC carries a tension of 800 N. Write this tension as a force T acting on point B in…

Q: A load W is to be lifted using the crane which is hinged at B as shown in the figure. The value of…

Q: Determine the tension in cable AB and the force developed in strut AC. (At the start, ASSUME AB and…

Q: *3-36. Cable ABC has a length of 5 m. Determine the positi on x and the tension developed in…

Q: Determine the mass (kg) of the heaviest cylinder that can be supported without exceeding a stress of…

Q: Situation 6. A 5 x 8–ft sign of uniform density weighs 270 lb and is supported by a ball-and-socket…

Q: A 5 x 8-ft sign of uniform density weighs 270 lb and is supported by a ball-and-socket joint at A…

Q: Situation 6. A 5 x 8-ft sign of uniform density weighs 270 lb and is supported by a ball-and-socket…

A: Given,

Q: 7.) (2 Points) Neglecting friction and the radius of the pulley. Determine the following: a.) the…

A: The diagram given in the question are as follows

Q: The rectangular beam ABC, 133 mm wide by 322 mm deep, is supported by a pin at A and the cable CD.…

Q: D 3 ft 5 ft 5 ft B The homogeneous 6000-lb bar ABC is supported by a pin at C and a cable that runs…

A: Given data in question Span member length Weight of Bar Hinge at point C Diameter of cable To find…

Concept explainers

Sizing Joists and Rafters

In civil engineering and building construction, joists and rafters are the major components including beams and columns. Almost every structural construction including buildings, skyscrapers, bridges, commercial complexes, and so on makes use of joists and rafters to provide structural integrity to the building. Joists are primarily thick long pieces of metals, concrete, or wood that are used to support the floor and ceiling. On the other hand, rafters form the major component of pitched roofs, which are a series of sloped long pieces extending from a ridged area that makes contact with the plane area of the wall. They account for the load-bearing of the building along with the beams.

Question

The homogeneous 860-kg bar AB is
supported by a ball-and-socket joint at A and
two cables attached to B. Find the tension in
cable CB.
B
4 m
3 m
4.5 m-
-
2.6 m
3 m
2.2 m
D
Figure P5.58

The homogeneous 25-kg bar AB is supported
by a ball-and-socket joint at A. End B, which
leans against a frictionless vertical wall, is
kept from sliding by the horizontal force P.
Determine Pand the force exerted by the
wall at B.
B
P
0.8 m
1.6 mj
25 kg
1.8 m
Figure P5.35

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Introduction

VIEW

Step 2 Data Given

VIEW

Step 3 Calculation of tension in cable

VIEW

Step 4 Conclusion

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Situation 2 | Beam ABCDEFG below is subjected to multiple loads as show. The total length of the beam is 10m. Analyze the beam completely. 6 kN 10 kN 3 kN/m 2 kN 5 kN-m G 3000mm. 1000mm 1000mm. 2000mm. 1000mm. 2000mm. 3. Determine the shear ation for segment B-C. ** 4. Determine the moment equation of segment C-D.**
The rigid bar BDE is welded at point B to the rolled-steel beam AC. 12kN load is applied 0.75m from A. a) Draw the V and Diagram and then calculate: b) the slope at point A, c) the deflection at point B. Use E-200 GPa. d) Maximum deflection and show its location. 12kN A BY D 20 kN/m E 60 KN -1.5 m 1.5 m-1.5 m C W410 X 85
1. Determine the resultant of the parallel force system acting on the bar AB shown. |15 knkm I5 KN/m Jo KN ** Im 6 m 2.5m 2.5m
3.81 A 500-N force is applied to a bent plate as shown. Determine (a) an equivalent force-couple system at B, (b) an equivalent system formed by a vertical force at A and a force at B. A B 125 mm Fig. P3.81 500 N 300 mm 30° $75 75 mm 175 mm
CE - PC 311 - STRUCTURAL THEORY Plate No. 10 - Analysis of Statically Indeterm in ate Beam s 1. By the moment-area m e thod c a lc u la te th e slopes of the e la stic curve at A, B and C and the vertic al de fle ctio n at C of the sim p le beam. E = 30,00 0 k/in and I = 300 in *. 2 Refer to th e fig ure b e lo w. AIl decim a ls m ust be inclu ded, do not round o ff answers. A Il figures must be in c luded and drawn straight. Curves may be done freehand. Sum marize your ans wers as shown below. Required V a lu es Answer B A X 1 X 2 X 1 X 2 kip ft ft 15.8 5 15 B.
The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. Determine the resultant internal loadings acting on the cross section at C. 600 N/m A. В D |C |-1 m--1 m-1 m ---1.5 m1.5 m 900 N
W=10kN/m 2m -1.5m. 150kN -0.5m B CROSS SECTION OF BEAM AB 30mm 30mm CALCULATE MAXIMUM BENDING AND SHEARING STRESS IN THE BEAM. 100mm 60mm 30mm 160mm 30mm
Q2: Analyze the frame and draw S.D and B.M? 10 kN/m 5 m El constant D 10 m
At-beam has a width of flange equal to 700mm and a thickness of 100mm. It has an effective depth of 450mm and the width of the web section is 350mm. It is reinforced at the bottom with a steel area of 2925sq.mm. fc'=17.24MPa, fy=413.7MPa. The depth of the compression block is _mm. A. 136.00mmB. 146.00mmC. 126.00mmD. 156.00mm
The rigid pipe BC shown is supported by a pin at C and an A- 36 guy wire AB (E = 200 GPa). The wire has a diameter of 8 mm. Determine the load P (kN) if the end B displaced 5.2 mm to the right. H = 3.5 m, 0 = 60°. A. 4.25 В. 6.30 C. 5.60 D. 3.23 H А
has a velbcnty 4- armls at A ard a Velocity Up= 15 m/s as it parses point B om the üclire. Fird frc between the block ard the plane x ='as. The bloch if s=180m aAd, aro
Before the load P was applied, a gap, ?0(2.75mm) existed between the cantilever beam AC andthe support at B. Knowing that E=200 GPa, determine the magnitude of P for which thedeflection at C is δ(5.5mm) and the reaction at B. (Hint: Use the method of superposition and beam deflections in Appendix A)