the high-pressure A supercritical reheat Rankine cycle has three stages of reheat. The steam state entering turbine is 30.5 MPa and 555°C. The steam expands to 5 MPa and is reheated to 455°C, reenters and expands to 1520 kPa, and is reheated to 410°C. It reenters the turbine and exhausts at 7.5 kPa. Draw T-S diagram. Determine (a) the quality or degrees of superheat of the stean entering the condenser; (b) the net work; (c) the cycle thermal efficiency.

the high-pressure A supercritical reheat Rankine cycle has three stages of reheat. The steam state entering turbine is 30.5 MPa and 555°C. The steam expands to 5 MPa and is reheated to 455°C, reenters and expands to 1520 kPa, and is reheated to 410°C. It reenters the turbine and exhausts at 7.5 kPa. Draw T-S diagram. Determine (a) the quality or degrees of superheat of the stean entering the condenser; (b) the net work; (c) the cycle thermal efficiency.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A regenerative steam power cycle with an open regenerator is used to produce a net power of 330 MW. The steam enters the first expansion stage at 12 MPa, 560°C and expands to 1 MPa, where part of the steam is extracted for regeneration. The rest of the steam continues to expand to 6 kPa. The feed water leaves the regenerator as a saturated liquid at 1 MPa. If the turbines and pumps are isentropic, calculate the following: (a) The thermal efficiency of the cycle. (b) The mass flow through the first stage of the turbine.
A gas turbine power plant operates on a simple thermodynamic cycle. The ambient conditionsare 100 kPa and 24 °C. The air at this condition enters the engine at 150 m/s whose diameteris 0.5 m. The pressure ratio across the compressor is 18 k and the temperature at the turbineinlet is 1400 K. Assuming ideal operation for all components and specific heats for air andproducts separately. In addition, neglect the mass of fuel burned. Do the followings:a. Choose the suitable thermodynamic cycleb.Draw pv and Ts diagram and label itCalculate the power required by the compressordDetermine the pressure and the temperature at the turbine exit,Compute the power produced by the turbinef.Available specific workg.The thermal efficiency
Consider a Rankine cycle with reheat in which steam enters the high-rate turbine at 500 psi and 1000 F from which it expands to 120 psi; the latter reheats to 1000 F expanding to 2 psi in the low- rate turbine. Calculate the thermal efficiency of the cycle 500 psia, 1000 F 120 psia 1000 F 2 psia
2. Consider a 210 MW steam power plant operating on an ideal Rankine cycle. Steam enters the turbine at 10 pressure of 10 kPa. Show the cycle on a T-s diagram MPa and 500°C and is cooled in the conder with respect to saturation lines, and determ Saved successfully im at the turbine exit, (b) the thermal efficiency of the cycle and (c) the mass flow rate of the steam. I ne isentropic efficiencies of both turbines are 80% and 85% respectively. pumps and
A reheat steam cycle has 13,580 kPa of throttle pressure at the turbine inlet and a 37.50308414 atm reheat pressure, the throttle and reheat temperature of the steam is 1302 R, condenser pressure is 4.3 kPa. If the efficiency at high – pressure and low – pressure turbine is 76% and 75%, determine the cycle efficiency, in percent.
High-P Low-P turbine turbine Reheater (4) Boiler P = Ps = Preheat Pump Condenser The following data was given for a steam power plant operating on the ideal reheat Rankine cycle. 3-4: Inlet steam at 17.5 MPa and 600 C 6-1: inlet steam at a pressure of 11.16 kPa at a wetness fraction of 01. At state 1, the specific volume is 0.00101 m/kg Find the specific entropy in kJ/kg at state 2 to 3 decimal places. Activate Windows
turbine turbine Reheater (4 Boiler P4= P5 = Prcheat Pump Condenser The following data was given for a steam power plant operating on the ideal reheat Rankine cycle. 3-4: Inlet steam at 17.5 MPa and 600 °C 6-1: inlet steam at a pressure of 11.16 kPa at a wetness fraction of 0 1 At state 1, the specific volume is 0.00101 m/kg Find the pressure in bar at state 6 to 3 decimal places
A steam powerplant runs using the Rankine cycle. The boiler operates at 5000 kPa and 500 °C. The turbine exhaust is saturated steam at 30 kPa and the pump efficiency is 0.75. Based on this information, select all the correct statements below. a. If the powerplant is operated isentropically, the turbine output will be wet steam with 0.78 quality. O b. If the powerplant is operated following the Carnot cycle, the thermal efficiency will increase by 118% C. If the condenser pressure is decreased, the overall thermal efficiency will also decrease. O d. If the powerplant is operated isentropically, the energy output of the turbine will be 1179 kJ/kg O e. The efficiency of the turbine is 0.75 Of. The overall thermal efficiency of the power plant is 0.255
A 150 MW gas turbine power plant running on Ideal Brayton cycle has the following initial conditions; air at 22°C & 95 kPa. The compression ratio is 7 and the temperature at the turbine is 910°C. Draw the P-V and T-S diagrams and determine the following: d. Thermal Efficiency e. Mass flow rate, kg/min
2. Steam enters the turbine of an ideal Rankine cycle at 8 MPa and expands adiabatically to 10 kPa. If the moisture content of the steam at the turbine exit is not to exceed 0.1, calculate the thermal efficiency of the cycle.
650 kg/min of superheated steam at 13 Mpa, 582 deg. C enters the turbine and initially expands isentropically to the pressure of 9.2 Mpa. After partial expansion, the steam was reheated with the same pressure at 9.2 Mpa and leaves the first reheater at 520 deg. C. It is once again expanded for the second partial expansion to a pressure of 5.4 Mpa where extraction of steam occurs. The remaining steam was reheated to a pressure of 4.9 Mpa and regained a temperature of 470 deg. C after the addition of heat in the second reheater. The final and complete isentropic expansion was executed until it reached an exhaust pressure of 0.04 Mpa. Draw the corresponding schematic diagram and its T-S diagram. Solve the following -total heat in MW -quality of steam before the condenser. -enthalpy entering the second reheater in KJ/Kg. -rejected heat by the condenser in MW. -net cycle work for the system in kJ/kg. -total reheating for the system in KW -net efficiency for the cycle. -turbine-generated…